ADS800E/1K - 12-Bit 40 MSPS ADC | Texas Instruments
MPN: ADS800E/1K ✗ 停產ADS800E/1K 概覽
An ADC is a data-acquisition semiconductor that converts an analog voltage into a numeric code for processing by a microcontroller, DSP, FPGA, or computer. The ADS800 belongs to the parallel-output ADC family within the broader ADC and data-converter hierarchy. Its 12-bit resolution provides 4,096 quantization levels, while its 40 MSPS conversion rate supports acquisition of substantially more samples than a conventional low-speed instrumentation ADC.
Key characteristics include 12-bit resolution, a maximum sampling rate of 40 MSPS, one analog input, parallel data output, a 28-pin SSOP package, and an industrial operating-temperature range of -40 °C to 85 °C. The parallel interface simplifies connection to suitably buffered digital logic and avoids the serial-link overhead associated with lower-rate converters. Its nominal 5 V supply also facilitates use in conventional industrial analog systems.
The ADS800E uses a pipelined conversion architecture, combining an internal reference with multiple functional stages to perform analog-to-digital conversion at 40 MSPS. A single-channel architecture makes it appropriate when the system does not require simultaneous sampling of multiple inputs. External multiplexing can extend the channel count, although settling time and acquisition-circuit requirements must then be evaluated for each multiplexed input.
Typical applications include communications-channel digitizers, industrial process monitoring, laboratory measurement systems, ultrasound and medical instrumentation interfaces, and digital feedback control loops. In each case, the 40 MSPS rate suits rapidly changing signals, while the 12-bit result supports thresholding, waveform analysis, envelope measurement, and supervisory control.
PCB design should provide a low-impedance analog input path, stable reference and supply bypassing, and careful routing of the 12-bit parallel bus. Use the manufacturer pin-description table when assigning tracks, and verify board-level timing against the clock and data-valid requirements in the datasheet. Because this converter is listed as obsolete, new designs should confirm lifecycle status and obtain an appropriate sourcing plan before committing the part to a production BOM.
This page consolidates the core electrical characteristics, lifecycle position, package information, cross-family upgrade paths, and engineering guidance for engineers evaluating the ADS800E/1K. It also distinguishes true pin-compatible options from merely similar converters so replacement decisions are based on resolution, throughput, interface, and thermal requirements.
直接替換替代品,適用於 ADS800E/1K — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
ADS800/1K
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
ADS800U/1K
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
ADS801/1K
✅ 直接替換📋 參考替代品(不在目錄中)
ADS802/1K
✅ 直接替換📋 參考替代品(不在目錄中)
ADS807E/1K
✅ 直接替換📋 參考替代品(不在目錄中)
ADS800E/1K 最大額定值與電氣特性
| 解析度 | 12 bit |
| 取樣率 | 40 MSPS |
| Number of Analog Inputs | 1 input |
| Number of A/D Converters | 1 converter |
| Data Interface | Parallel |
| Conversion Architecture | Pipelined |
| 供應電壓 | 5 V nominal |
| 工作溫度 | -40 °C to 85 °C |
| 封裝 | 28-pin SSOP |
| Package Width | 5.3 mm |
| 安裝類型 | Surface mount |
| Terminal Count | 28 terminals |
| Lead Form | Gull wing |
| Temperature Grade | Industrial |
| RoHS 狀態 | Compliant |
ADS800E/1K 5.3 mm 腳位配置指南
ADS800E/1K(5.3 mm 封裝)的腳位配置。 此類比元件具有輸入、輸出與電源腳位。偏移歸零、補償與致能腳位配置請參閱製造商資料表。適用於訊號調理與放大器電路。
無詳細腳位定義資料: ADS800E/1K.
請參閱 資料表 以查看完整腳位配置。
典型應用
ADS800E/1K 適用於 6 應用s: Communications Receiver Digitization, Industrial Process Measurement, Digital Feedback Control, Laboratory Data Acquisition, Medical and Diagnostic Instrumentation, Waveform Monitoring and Analysis.
Communications Receiver Digitization
The ADS800E/1K fits receiver and demodulation stages that need 12-bit quantization at up to 40 MSPS. Its parallel output supports direct capture by an FPGA, DSP, or logic device without a low-speed serial link. The single input is appropriate when one modulated or intermediate-frequency channel is sampled at a time. Designers should place the converter behind a gain-controlled, band-limiting front end and verify that clock jitter, analog bandwidth, and output timing preserve signal integrity at the intended operating rate.
推薦
Industrial Process Measurement
The ADS800E/1K can digitize rapidly varying sensor signals in industrial monitoring and control systems. Its 12-bit result provides 4,096 quantization levels, while the 40 MSPS rate captures more detail than a conventional slow ADC. The -40 °C to 85 °C industrial range supports equipment deployed across moderate industrial environments. A practical implementation uses a buffered sensor input, an anti-alias filter, and grounded digital return paths so switching circuitry does not corrupt the measurement.
推薦
Digital Feedback Control
The ADS800E/1K is appropriate for control loops requiring faster feedback than a general-purpose low-speed ADC provides. At 40 MSPS, it can sample a control or transducer signal and present a 12-bit parallel result to a DSP or FPGA. The pipeline architecture supports sustained conversion, while the one-input arrangement keeps the analog front end manageable. Loop design must account for propagation delay, output latency, filtering, and actuator limits so higher sample throughput does not inadvertently destabilize the control system.
推薦
Laboratory Data Acquisition
The ADS800E/1K supports laboratory and test systems that sample a single analog channel at up to 40 MSPS. Its 12-bit parallel output can feed capture logic, a counter, or a processing FPGA, allowing sample-by-sample inspection of transient behavior. Instrumentation designs should use shielded analog routing, separate analog and return-current paths, and a clean clock source. Calibration records should capture gain and offset behavior because these characteristics influence accuracy more than resolution alone.
推薦
Medical and Diagnostic Instrumentation
The ADS800E/1K can serve as the conversion stage in diagnostic equipment that captures a rapidly changing physiological or sensor-derived waveform. The 40 MSPS rate provides dense temporal samples, and the 12-bit parallel output can be processed by an FPGA. Because medical systems impose strict safety, isolation, and signal-integrity requirements, the converter must remain inside the appropriately isolated analog front end. Input protection, leakage, calibration, and patient-safety boundaries must be validated independently of the ADC datasheet.
推薦
Waveform Monitoring and Analysis
The ADS800E/1K is useful for monitoring pulsed, transient, or repeating waveforms when a higher temporal resolution is required. Its single-channel pipelined ADC samples at 40 MSPS and provides a parallel code for thresholding, peak detection, spectral analysis, or time-domain processing. The analog front end should limit bandwidth according to the highest signal component of interest and provide the converter with a stable common-mode range. Clocking and capture timing should be derived from a low-jitter source to preserve amplitude accuracy.
推薦
推薦產品摘要
工程參考資料,適用於 ADS800E/1K — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | ADS800/1K | ADS800U/1K | ADS801/1K | ADS802/1K | ADS807E/1K |
|---|---|---|---|---|---|---|
| Package | 28-pin SSOP | 28-pin SSOP | 28-pin SSOP | 28-pin SSOP | 28-pin SSOP | 28-pin SSOP |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Resolution | 12 bit | 12 bit | 12 bit | 12 bit | 13 bit | 12 bit |
| Sampling Rate | 40 MSPS | 40 MSPS | 40 MSPS | 80 MSPS | 40 MSPS | 53 MSPS |
| Data Interface | Parallel | Parallel | Parallel | Parallel | Parallel | Parallel |
| Supply Voltage | 5 V nominal | 5 V nominal | 5 V nominal | 5 V nominal | 5 V nominal | 5 V nominal |
主要差異化特點
- Lower conversion rate preserves a straightforward 40 MSPS acquisition point (對比ADS807E/1K)
- 12-bit output matches the original parallel data architecture (對比ADS802/1K)
- 40 MSPS throughput is half that of the higher-rate family member (對比ADS801/1K)
設計說明
Route the analog input as a short, controlled-impedance path directly from the front end to the converter. Keep the input node physically small, use a continuous ground reference beneath the analog section, and separate the 12-bit output bus from the analog input. The manufacturer datasheet's recommended application circuit should be the starting point for component placement and grounding.
Provide the converter with a stable 5 V nominal supply and place the manufacturer-recommended bypass capacitors close to the supply and ground pins. Avoid sharing narrow supply traces with clocking or high-current digital circuitry. Because the 40 MSPS conversion rate can increase dynamic power demand, verify supply droop and decoupling under the intended digital load rather than evaluating only static current.
Use a low-jitter clock and match output timing to the receiving FPGA, DSP, or capture logic. The 12-bit parallel bus creates numerous simultaneous switching edges, so account for trace length, return paths, and the receiving device's setup and hold requirements. For replacement with ADS801/1K, ADS802/1K, or ADS807E/1K, repeat the timing validation because sampling rate, resolution, or latency can differ.
Do not assume that an equal package guarantees identical system behavior. Confirm the analog input range, reference arrangement, clock polarity, output timing, conversion latency, and operating-temperature grade against the manufacturer datasheet. A 13-bit replacement also requires downstream handling to recognize the additional code bit, while faster replacements may exceed the capture capability of the original board.
合規資訊
RoHS compliance is identified by the product listing. No verified automotive qualification, REACH declaration, halogen-free declaration, lead-free statement, or conflict-minerals declaration was identified.