ATSAML11D14A-YF - 32MHz Cortex-M23 Secure MCU | Microchip
MPN: ATSAML11D14A-YF ✓ 啟用中ATSAML11D14A-YF 概覽
An Arm Cortex-M23 microcontroller is a 32-bit embedded processor within the microcontroller and semiconductor hierarchy. It executes interrupt-driven firmware for control, measurement, communications, and security functions while adding the efficiency expected from an embedded processor. The ATSAML11D14A-YF also integrates SERCOM peripherals, ADC, DAC, op amp, and other analog resources, reducing the need for discrete support components in connected low-power equipment.
The device operates at up to 32 MHz and includes 16 KB of flash, 8 KB of SRAM, and 2 KB of EEPROM. According to the Microchip product page, active-mode consumption is less than 25 uA/MHz and sleep-mode consumption is less than 100 nA. These figures make the microcontroller appropriate for duty-cycled systems that spend most of their operating time between brief processing intervals.
Security is implemented at the chip level rather than relying only on software controls. Arm TrustZone-M separates secure and non-secure software, while secure key storage, crypto accelerators, and tamper-resistance features protect credentials and sensitive operations. These capabilities are particularly relevant to connected devices that update firmware, store authentication material, or communicate across trust boundaries.
Typical uses include secure IoT endpoints, industrial sensing modules, low-power condition-monitoring equipment, compact security controllers, and connected measurement products. The integrated ADC and DAC support analog signal acquisition and output, while SERCOM interfaces support compact serial communications. The 24-SSOP package is appropriate for designs requiring more conventional through-hole-style lead access than fine-pitch QFN alternatives without using a large board area.
PCB planning should preserve access to all 24 package leads and provide the decoupling and signal-integrity layout specified by the manufacturer datasheet. Pay particular attention to exposed supply, ground, reset, and programming pins when routing the board. For firmware development, confirm the supported ATSAML11 family toolchain, debugger, boot configuration, and peripheral pin-mux requirements before committing the PCB layout.
This page combines the key electrical characteristics, verified ordering information, secure-I/O feature set, and practical replacement guidance for engineers evaluating the ATSAML11D14A-YF as a compact low-power Cortex-M23 design platform.
直接替換替代品,適用於 ATSAML11D14A-YF — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: ATSAML11D14A-YF (相同外形與佔位) — 差異在於 Package, Core Architecture, Active Mode Current, Operating Temperature Range, RoHS Status.
ATSAML11D14A-YU
✅ 直接替換聯絡詢價
查看資料表 →ATSAML11D14A-YFT
✅ 直接替換聯絡詢價
查看資料表 →ATSAML11D15A-YF
✅ 直接替換聯絡詢價
查看資料表 →ATSAML11D14A-YF 最大額定值與電氣特性
| Product Type | 32-bit ARM Cortex-M23 Microcontroller |
| Architecture | Single-core ARM Cortex-M23 |
| 最大時脈頻率 | 32 MHz |
| Flash Memory | 16 KB (16K x 8) |
| SRAM | 8 KB |
| EEPROM | 2 KB |
| Security | ARM TrustZone-M, secure key storage, crypto, and tamper resistance |
| Peripheral Interfaces | SERCOM, ADC, DAC, OPAMP, and AC |
| Active Mode Current | <25 uA/MHz |
| Sleep Mode Current | <100 nA |
| 封裝 | 24-SSOP |
| Package Dimensions | 0.209 in x 5.30 mm |
| 安裝類型 | Surface Mount |
ATSAML11D14A-YF 0.209 in x 5.30 mm 腳位配置指南
ATSAML11D14A-YF(0.209 in x 5.30 mm 封裝)的腳位配置。 此數位 IC 包含 GPIO、通訊介面(UART、SPI、I2C)與電源腳位。替代腳位功能與配置選項請參閱製造商資料表。對嵌入式系統設計與 PCB 佈局至關重要。
無詳細腳位定義資料: ATSAML11D14A-YF.
請參閱 資料表 以查看完整腳位配置。
典型應用
ATSAML11D14A-YF 適用於 6 應用s: Secure IoT Sensor Endpoint, Industrial Condition Monitoring, Low-Power Environmental Sensor, Secure Authentication Controller, Compact Control and Signal Generator, Battery-Powered Remote Monitoring.
Secure IoT Sensor Endpoint
The ATSAML11D14A-YF fits secure IoT sensor endpoints that require authenticated connectivity and low standby consumption. Its 32 MHz Arm Cortex-M23 core handles protocol tasks and sensor control, while TrustZone-M, secure key storage, crypto hardware, and tamper resistance protect credentials and firmware boundaries. The 16 KB flash and 8 KB SRAM suit compact constrained firmware rather than complex edge-AI workloads. Active current below 25 uA/MHz and sleep current below 100 nA support duty-cycled operation. Use the integrated ADC for analog sensing and SERCOM for serial sensor or communications links. Before schematic capture, confirm the selected radio interface, pin multiplexing, device-unique key workflow, and low-power wake behavior against the manufacturer documentation.
推薦
Industrial Condition Monitoring
The ATSAML11D14A-YF is appropriate for industrial condition-monitoring modules that sample sensors, evaluate thresholds, and report events without a large host processor. The 32-bit Cortex-M23 architecture supports deterministic interrupt handling, while the integrated 12-bit ADC, DAC, op amp, and analog comparator reduce the analog front-end footprint. Firmware can wake from sleep for periodic measurements, exploit less than 100 nA sleep consumption, and use less than 25 uA/MHz during processing. SERCOM provides a flexible path to digital sensors or field-bus transceivers. Design the analog front end around the manufacturer’s ADC reference and input recommendations, provide filtering appropriate to the sensor bandwidth, and isolate high-energy motor or relay nodes to prevent conducted noise from corrupting measurements.
推薦
Low-Power Environmental Sensor
The ATSAML11D14A-YF supports compact environmental sensors that combine analog measurement, local thresholding, and secure data handling. Its integrated ADC accepts sensor outputs, while the DAC and op amp can support excitation, compensation, or local test functions. The Cortex-M23 core can execute filtering and calibration without a separate processor, and the 16 KB flash provides room for application firmware and configuration data. For battery-powered operation, keep the MCU in sleep between measurements and use a peripheral event to trigger conversions; the manufacturer reports sleep current below 100 nA and active current below 25 uA/MHz. Select external passive components and reference circuitry for the required accuracy, and verify ADC noise, input impedance, and sampling time before final calibration.
推薦
Secure Authentication Controller
The ATSAML11D14A-YF can serve as a compact authentication controller for connected accessories, equipment nodes, and access-control products. TrustZone-M separates trusted security code from application code, while secure key storage, crypto hardware, and tamper resistance improve protection of credentials compared with a software-only implementation. The 32 MHz Cortex-M23 core is sufficient for challenge-response protocols, key derivation, policy checks, and serial command handling, and 2 KB EEPROM can retain configuration parameters. Keep the firmware update path authenticated and validate the device’s tamper-detection behavior in the final enclosure. The 24-SSOP footprint also supports designs that prefer accessible leads, although the security boundary ultimately depends on correct key provisioning, startup configuration, and physical package handling.
推薦
Compact Control and Signal Generator
The ATSAML11D14A-YF is suitable for compact control and signal-generation products where an MCU, ADC, DAC, op amp, and comparator can share one package. A product can acquire a control or sensor signal through the ADC, calculate an adjustment in the Cortex-M23 core, and drive a reference waveform through the DAC. The 32 MHz processing rate supports responsive control loops, while TrustZone-M can isolate safety- or security-sensitive routines from ordinary application code. SERCOM channels permit connection to display, communications, or storage devices without consuming separate serial-interface controllers. Verify DAC output range, ADC reference behavior, comparator thresholds, and pin-mux alternatives in the manufacturer documentation. Keep analog routing away from fast digital edges and provide local decoupling at every supply pin.
推薦
Battery-Powered Remote Monitoring
The ATSAML11D14A-YF fits battery-powered remote-monitoring devices that periodically acquire information and transmit it through a low-power serial link. Its Cortex-M23 core handles scheduling and data preparation, and the SERCOM peripherals support integration with a communications module without requiring a dedicated protocol controller. Low sleep current below 100 nA is valuable when the radio remains the dominant load, while active current below 25 uA/MHz helps control the processing portion of each wake cycle. The integrated ADC can directly monitor a sensor or battery-divider signal, but its voltage range and accuracy must match the application. Use a regulator with suitable quiescent current, add decoupling close to the supply pins, and validate battery-life estimates with the actual radio duty cycle rather than microcontroller current alone.
推薦
推薦產品摘要
工程參考資料,適用於 ATSAML11D14A-YF — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | ATSAML11D14A-YU | ATSAML11D14A-YFT | ATSAML11D15A-YF |
|---|---|---|---|---|
| Package | 24-SSOP | 24-SSOP | 24-SSOP | 24-SSOP |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Processor Core | ARM Cortex-M23 | ARM Cortex-M23 | ARM Cortex-M23 | ARM Cortex-M23 |
| Maximum Clock Frequency | 32 MHz | 32 MHz | 32 MHz | 32 MHz |
| Flash Memory | 16 KB | 16 KB | 16 KB | 24 KB (+50%) |
| SRAM | 8 KB | 8 KB | 8 KB | 8 KB |
主要差異化特點
- Combines Cortex-M23 processing with chip-level security (對比ATSAML11D14A-YU)
- Low-power operation for duty-cycled embedded designs (對比ATSAML11D15A-YF)
- Integration reduces discrete analog support (對比ATSAML11D14A-YFT)
設計說明
Assign the ATSAML11D14A-YF footprint from the 24-SSOP package drawing in the Microchip manufacturer datasheet, including lead pitch, row span, solder-mask clearance, and paste-land dimensions. Confirm that every power, ground, reset, programming, and peripheral signal lead remains accessible. Do not reuse a generic 24-SSOP footprint without checking the exact package width and lead geometry.
Place the required bypass capacitors directly between the appropriate supply and ground pins, using the shortest possible traces. Follow the manufacturer’s recommended capacitance, voltage rating, and dielectric requirements. For battery-powered systems, calculate the regulator’s quiescent current together with active and sleep consumption; the MCU’s below-25-uA/MHz active figure and below-100-nA sleep figure do not include external regulator or radio losses.
Separate analog inputs associated with the ADC from fast SERCOM, switching-regulator, and digital clock routes. Use a continuous ground reference, avoid routing sensitive inputs beneath digital or power-regulator nodes, and place analog filtering close to the source. The integrated op amp and comparator require layout that minimizes parasitic capacitance and keeps high-current returns from sharing sensitive return paths.
Do not select an ATSAML11 replacement from the base device name alone. Verify the package, temperature grade, flash capacity, pin multiplexing, security features, and firmware configuration for every order code. ATSAML11D14A-YU and ATSAML11D14A-YFT appear closely matched, but their temperature specifications must be confirmed. ATSAML11D15A-YF adds 8 KB of flash and should be treated as a different memory configuration until compatibility is established.
合規資訊
The ATSAML11D14A-YF product and distributor records do not state the requested compliance classifications. Confirm RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals status with the manufacturer before qualification.