ATTINY26L-8MU - 8MHz AVR MCU with 2KB Flash | Microchip
MPN: ATTINY26L-8MU ✓ 啟用中ATTINY26L-8MU 概覽
An 8-bit microcontroller is a compact embedded-control device that executes firmware to monitor inputs, control outputs, and process data through timers, interrupts, serial interfaces, and analog peripherals. The ATtiny26 belongs to the TinyAVR family, combining a reduced instruction set computer core with Flash memory and mixed-signal peripherals in a small surface-mount package. This hierarchy places it within embedded processing, specifically low-cost, low-power AVR microcontrollers.
Key features include a maximum clock frequency of 8 MHz, 2 KB of Flash organized as 1K x 16, 128 bytes of EEPROM, and 128 bytes of internal SRAM. Peripherals include an ADC, I2C, SPI, an analog comparator, an 8/16-bit timer/counter with prescaler, an 8/10-bit high-speed timer/counter with PWM, a programmable watchdog timer, and pin-change interrupts on 11 pins. Low-power idle, noise-reduction, and power-down modes support battery-operated equipment.
The AVR enhanced RISC architecture supports single-clock-cycle instruction execution for many common operations, allowing the 8 MHz device to perform control tasks without a larger processor. Its small memory capacity favors compact firmware, while the exposed-pad VQFN construction supports compact PCB placement and thermal dissipation. Designers should use the pin-description table in the manufacturer datasheet when assigning tracks and connecting the exposed pad.
Typical uses include compact motor controllers, battery-powered sensors, LED lighting controls, fan controllers, simple security panels, and small industrial automation modules. The ATtiny26L's low-voltage range is particularly useful in 3.3 V systems where a 5 V-only MCU would not provide adequate operating margin.
When designing around the ATTINY26L-8MU, place the decoupling capacitor beside each applicable supply pin and preserve the exposed-pad land pattern. Confirm the regulator's startup behavior, output-voltage tolerance, and timing requirements with the firmware configuration. The 2 KB Flash limit also requires disciplined code sizing during toolchain selection and validation.
This page combines the manufacturer's ATtiny26 summary information with package details, application guidance, engineering notes, and a strict drop-in replacement assessment. It also highlights when the low-voltage ATtiny26L is preferable to a standard ATtiny26 and where firmware, qualification, or supply requirements should drive a different choice.
直接替換替代品,適用於 ATTINY26L-8MU — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
ATTINY26-8MU
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
ATTINY26L-8MU 最大額定值與電氣特性
| Architecture | 8-bit AVR enhanced RISC |
| 最大時脈頻率 | 8 MHz |
| Flash Program Memory | 2 KB (1K x 16) |
| EEPROM Memory | 128 bytes |
| Internal SRAM | 128 bytes |
| 工作電源電壓 | 2.7 V to 5.5 V |
| 工作溫度範圍 | -40 °C to +85 °C |
| 封裝 | 32-VQFN, 5 x 5 mm, exposed pad |
| 安裝類型 | Surface mount |
| ADC | Present |
| Serial Interfaces | I2C and SPI |
| Analog Comparator | Present |
| Timer/Counter 0 | 8/16-bit with prescaler |
| High-Speed Timer/Counter 1 | 8/10-bit with PWM |
| Programmable Watchdog Timer | Present with separate on-chip oscillator |
| Pin-Change Interrupts | 11 pins |
| Low-Power Modes | Idle, noise-reduction, and power-down modes |
ATTINY26L-8MU 32-vqfn, 5 x 5 mm, exposed pad 腳位配置指南
ATTINY26L-8MU(32-vqfn, 5 x 5 mm, exposed pad 封裝)的腳位配置。 此數位 IC 包含 GPIO、通訊介面(UART、SPI、I2C)與電源腳位。替代腳位功能與配置選項請參閱製造商資料表。對嵌入式系統設計與 PCB 佈局至關重要。
無詳細腳位定義資料: ATTINY26L-8MU.
請參閱 資料表 以查看完整腳位配置。
典型應用
ATTINY26L-8MU 適用於 6 應用s: Battery-Powered Sensor Nodes, Compact LED Lighting Control, Small Motor and Fan Controllers, IoT Remote Sensor Interface, Battery Charging Monitor, Compact Security and Access Panel.
Battery-Powered Sensor Nodes
The ATTINY26L-8MU fits compact battery-powered sensing because its supply range begins at 2.7 V and it supports idle, noise-reduction, and power-down modes. A 3.3 V regulated rail can power the controller without relying on the standard ATtiny26's 4.5 V minimum. Its 8 MHz AVR core is sufficient for sampling and conditioning sensor data, while I2C and SPI provide direct links to compatible sensors and transceivers. The 128-byte SRAM and 2 KB Flash require compact firmware, but they also reduce footprint and energy use. Firmware should activate a low-power mode between measurements and use the watchdog timer to recover from unexpected stalls.
推薦
Compact LED Lighting Control
The ATTINY26L-8MU is appropriate for compact LED lighting control because its high-speed timer/counter provides PWM while the I2C interface can connect to a lighting controller or digital sensor. The 8 MHz operating speed supports responsive user input and lighting effects, and the 2.7 V to 5.5 V range permits low-voltage designs. Its 128 bytes of SRAM can hold a modest animation state, while EEPROM can retain brightness or configuration settings. Because the microcontroller has limited program memory, designers should avoid large animation tables and should time the PWM output against the intended LED driver rather than driving high current directly from an MCU pin.
推薦
Small Motor and Fan Controllers
The ATTINY26L-8MU can manage small motor or fan systems where adjustable drive, current monitoring, and compact control are required. Its two timer blocks provide timing and PWM resources, while the ADC and analog comparator can support feedback or protection signals. The 8 MHz clock gives deterministic timing for commutation, stall detection, and speed updates, and the 2.7 V minimum supply suits compact 3.3 V systems. The MCU should drive a transistor or dedicated power stage rather than the motor directly. Use local current limits and verify that the external power stage remains compatible with the startup and shutdown behavior required by the load.
推薦
IoT Remote Sensor Interface
The ATTINY26L-8MU works well as a low-resource interface between sensors and a network or gateway processor. I2C and SPI allow it to communicate with digital sensors and radio modules, while the ADC supports analog front-end readings and the 8 MHz core can format measurements for transmission. Its small 32-VQFN 5 x 5 mm package supports compact IoT hardware, and the 2.7 V to 5.5 V operating range accommodates low-voltage sensor systems. Firmware architecture must account for only 2 KB of Flash and 128 bytes of SRAM, so packet buffering and protocol processing should remain on the gateway whenever possible.
推薦
Battery Charging Monitor
The ATTINY26L-8MU can supervise a small battery-backed system by measuring voltage through the ADC and coordinating status information over I2C or SPI. Its low-voltage operation is useful near the discharge end of a 3.3 V battery rail, while the watchdog timer and low-power modes support unattended operation. The 8/16-bit timer/counter can provide periodic measurement timing, and EEPROM can retain configuration or calibration values. Firmware should define valid measurement windows, fault thresholds, and recovery behavior before the controller is connected to a charging circuit, particularly if an external charger can change the rail voltage quickly.
推薦
Compact Security and Access Panel
The ATTINY26L-8MU can manage a compact access-control or alarm panel that needs local input handling and short-range communication. Pin-change interrupts on 11 pins support responsive reactions to switches, contact sensors, or tamper inputs, while the ADC and analog comparator can monitor additional analog conditions. The 2 KB Flash is adequate for focused firmware rather than a large graphical interface, and EEPROM can store limited configuration data. The 32-VQFN footprint helps reduce board area in compact industrial enclosures. Security-sensitive designs should add suitable external protection and must not treat the device's limited memory and general-purpose peripherals as a substitute for a dedicated cryptographic security element.
推薦
推薦產品摘要
工程參考資料,適用於 ATTINY26L-8MU — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | ATTINY26-8MU |
|---|---|---|
| Brand | Microchip Technology | Microchip Technology |
| Package | 32-VQFN (5x5) | 32-VQFN (5x5) |
| Maximum Clock Frequency | 8 MHz | 8 MHz |
| Operating Supply Voltage | 2.7 V to 5.5 V | 4.5 V to 5.5 V |
| Flash Memory | 2 KB (1K x 16) | 2 KB (1K x 16) |
| EEPROM | 128 bytes | 128 bytes |
| Internal SRAM | 128 bytes | 128 bytes |
| Operating Temperature Range | -40 °C to +85 °C | -40 °C to +85 °C |
| Low-Voltage Operation | Supported from 2.7 V | Not supported below 4.5 V |
| Key Peripherals | ADC, I2C, SPI, comparator, timers, PWM, watchdog | ADC, I2C, SPI, comparator, timers, PWM, watchdog |
主要差異化特點
- Lower minimum operating voltage (對比ATTINY26-8MU)
- Same 8 MHz clock capability (對比ATTINY26-8MU)
- Compact exposed-pad package (對比ATTINY26-8MU)
設計說明
Use the package drawing in the Microchip ATtiny26 Summary Datasheet to define the 32-VQFN 5 x 5 mm land pattern and exposed-pad connection. Place the device-side input and output decoupling capacitors close to their corresponding supply pins, with short return paths to the ground plane. Do not substitute a generic 32-pin QFN footprint without checking pad dimensions, exposed-pad size, pin numbering, and solder-mask clearance.
Design the supply for the ATtiny26L's full 2.7 V to 5.5 V range, including startup, transient response, and the maximum 8 MHz operating condition. Keep the regulator's permitted minimum output above 2.7 V after tolerance and voltage drop are considered. A 3.3 V rail is appropriate, but the MCU and any connected peripherals must also tolerate the selected rail. Verify brownout and power-down behavior in firmware rather than assuming a reset always preserves the intended operating state.
Keep the exposed pad and surrounding ground plane electrically continuous while respecting the manufacturer's thermal-via recommendations. Separate noisy switching-node copper from ADC, comparator, and oscillator-related routing where practical. I2C and SPI traces should be short and have compatible pull-up arrangements, and unused inputs should be tied to a defined level. Review the final layout against the package drawing and the pin table for the exact ordering suffix.
The most consequential substitution error is confusing the low-voltage ATtiny26L with the standard ATtiny26. ATTINY26L-8MU supports 2.7 V to 5.5 V, whereas the standard family device is specified from 4.5 V to 5.5 V. A second common error is changing package suffixes without redesigning the PCB. Also account for the 2 KB Flash and 128-byte SRAM limits before committing to a larger application framework or communication protocol.
合規資訊
The manufacturer product and summary-datasheet information does not establish a specific compliance declaration for the ATTINY26L-8MU ordering code. Request current RoHS, REACH, lead-free, halogen-free, conflict-minerals, and automotive qualification documentation through the Request a Quote form.