DG405AK - Dual High-Speed 35Ohm Analog Switch | Maxim
MPN: DG405AK ✓ 啟用中DG405AK 概覽
An analog switch is an interface IC that connects or disconnects a signal path under digital control. The DG405AK belongs to the broader analog-switch hierarchy, which includes multiplexers, demultiplexers, and CMOS switch ICs used in data acquisition, test, communications, instrumentation, and signal-routing systems. Its normally open architecture leaves each channel disconnected until the corresponding control signal activates it.
The redesigned DG405 family provides guaranteed on-resistance matching between the two switches of 2 ohm maximum and guaranteed on-resistance flatness over the signal range of 3 ohm maximum. The manufacturer also identifies a typical on resistance of 20 ohm. These characteristics help reduce channel-dependent amplitude error and distortion when the same signal is routed through different switch paths. The distributed 35 ohm value identifies the DG405AK configuration and should be checked against the operating signal range during design.
The DG405AK uses dual SPST CMOS switching elements and high-speed control logic. Two switches provide separate routing decisions rather than multiplexing a larger number of inputs through one common terminal. This arrangement is useful when a system must select between two signal paths, isolate a source from a downstream instrument, or implement a sample-and-hold acquisition network. Exact switching-time, voltage, leakage, and channel-count details must be confirmed in the manufacturer data sheet.
Typical applications include precision signal routing in data-acquisition systems, switched-capacitor filter control, audio and communications routing, automated test equipment, and laboratory instrumentation. The matched on-resistance specification is especially valuable when comparing channels in instrumentation, while the high-speed architecture suits systems that require rapid settling between measurement or routing states. External clocking, drive levels, and control timing must remain within the device's documented operating limits.
Design the surrounding circuit so that signal amplitude, bandwidth, and transient current remain compatible with the switch. Place bypass and protection components close to the supply and signal pins, and use controlled-impedance routing when signals are sensitive to reflection or crosstalk. Account for off-state isolation, charge injection, and control-logic timing when planning precision measurements or synchronous acquisition sequences.
This page combines the manufacturer's DG405 family information, package and configuration details, and practical routing guidance with a pin-compatible comparison focused on military-qualified DG405 variants. It is intended to help engineers identify the correct switch configuration, verify package compatibility, and plan the surrounding analog signal path before releasing a PCB design.
直接替換替代品,適用於 DG405AK — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
DG405AK/883B
✅ 直接替換📋 參考替代品(不在目錄中)
DG405AK/883
✅ 直接替換📋 參考替代品(不在目錄中)
DG405AK 最大額定值與電氣特性
| Number of Circuits | 2 circuits |
| Multiplexer Configuration | 2:1 configuration |
| Switch Architecture | Dual SPST channels |
| Signal State | Normally open |
| On Resistance | 35 ohm |
| Typical On Resistance | 20 ohm |
| On-Resistance Matching Between Switches | 2 ohm maximum |
| On-Resistance Flatness Over Signal Range | 3 ohm maximum |
| Technology | CMOS analog switch |
| 封裝 | 16-pin CERDIP |
| Package Pitch | 0.300 inch (7.62 mm) |
| 安裝類型 | Through-hole |
| Qualification Variant | DG405AK/883B is a 5962-89961 qualified variant |
| Turn-On Time | 150 ns maximum for DG405AK/883 |
| Turn-Off Time | 100 ns maximum for DG405AK/883 |
| 生命週期狀態 | Production |
DG405AK 0.300 inch (7.62 mm) 腳位配置指南
DG405AK(0.300 inch (7.62 mm) 封裝)的腳位配置。 腳位編號、功能與連接圖定義於製造商資料手冊中。請參閱該手冊以取得確切的封裝尺寸與焊接指引。
無詳細腳位定義資料: DG405AK.
請參閱 資料表 以查看完整腳位配置。
典型應用
DG405AK 適用於 6 應用s: Precision Data-Acquisition Routing, Switched-Capacitor Filter Control, Automated Test Equipment, Audio Signal Routing, Communications Signal Isolation, Laboratory Instrumentation.
Precision Data-Acquisition Routing
The DG405AK fits precision acquisition routing because its two normally open SPST channels can isolate or connect separate analog sources while the family guarantees on-resistance matching of 2 ohm maximum. This matching helps limit channel-dependent gain errors when the same measurement path is calibrated across multiple inputs. The typical 20 ohm on resistance also supports practical acquisition front ends. Confirm signal bandwidth, charge injection, leakage, and settling behavior against the manufacturer data sheet before finalizing the front end.
推薦
Switched-Capacitor Filter Control
The DG405AK can control the switching elements in a switched-capacitor filter when the required operating frequency and settling interval fit the device's documented limits. Its dual SPST arrangement supports independent charge-transfer paths, while the DG405 family's typical 20 ohm on resistance can influence the effective settling behavior of each capacitor network. Design the control waveform to avoid overlap during charge transfer and include switch capacitance and charge injection in the filter simulation.
推薦
Automated Test Equipment
DG405AK suits automated test equipment that needs to route one of two analog conditions into a measurement chain. The guaranteed 2 ohm maximum matching between switches helps maintain repeatability when a path is switched during calibration or diagnostic sequencing. The 16-pin CERDIP package also supports legacy and rugged through-hole assemblies. Verify isolation, leakage, control levels, and qualification requirements at the system level, particularly where long test cables can introduce additional noise and capacitance.
推薦
Audio Signal Routing
The DG405AK can route low-frequency audio signals between two paths where normally open SPST behavior and controlled on resistance are important. Its 35 ohm identified on resistance and the family's 20 ohm typical value can be included in the signal-path loss budget, while the 2 ohm maximum matching helps avoid audible channel imbalance in balanced routing architectures. The designer should still check distortion, off-state isolation, ground leakage, and bandwidth against the particular preamplifier and source impedance.
推薦
Communications Signal Isolation
DG405AK is applicable to communications equipment that requires a normally open analog isolation path between a transmitter, receiver, or test network. Two independent channels provide routing flexibility without forcing a common multiplexed node, while the high-speed switch family is intended for rapid signal-path changes. Check the maximum signal voltage, supply requirements, control timing, insertion loss, and isolation at the operating frequency. Board-level EMI performance will also depend on impedance matching and grounding outside the IC.
推薦
Laboratory Instrumentation
The DG405AK can select or disconnect signals in laboratory instruments where channel consistency and ceramic-DIP construction are useful. The DG405 family's guaranteed on-resistance matching of 2 ohm maximum reduces path variation between the two switches, while on-resistance flatness of 3 ohm maximum supports predictable behavior across the specified signal range. For precision meters and source-measure systems, validate leakage, noise, charge injection, and settling time with the complete front-end network rather than relying on the on resistance alone.
推薦
推薦產品摘要
工程參考資料,適用於 DG405AK — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | DG405AK/883B | DG405AK/883 |
|---|---|---|---|
| Brand | Maxim Integrated | Maxim Integrated | Maxim Integrated |
| Package | 16-pin CERDIP | 16-CDIP | 16-CDIP |
| Number of Circuits | 2 circuits | 2 circuits | 2 circuits |
| Switch Configuration | Dual SPST | Dual SPST | Dual SPST |
| Qualification Designation | Standard DG405AK | 5962-89961 | /883 designation |
| Signal State | Normally open | Normally open | Normally open |
| Mounting Type | Through-hole | Through-hole | Through-hole |
主要差異化特點
- Lower documented on resistance in the qualified ordering code (對比DG405AK/883B)
- Military-qualified designation for controlled procurement (對比DG405AK)
- Documented high-speed transition timing (對比DG405AK)
設計說明
Model the switched path as a frequency-dependent resistance rather than using only the 35 ohm DC value. Include source and load impedance, switch capacitance, and the complete routing geometry when estimating attenuation or settling time. For fast edges, keep the route short and provide a continuous return path so switching current does not couple into sensitive analog nodes.
Assign the PCB footprint from the manufacturer package drawing rather than treating every ceramic DIP as electrically or mechanically interchangeable. Confirm row spacing, lead pitch, body dimensions, and pin-one orientation. Maintain adequate clearance around the 16-pin CERDIP and keep analog signal traces away from digital control nets to reduce switching crosstalk.
Do not infer that DG405AK, DG405AK/883, and DG405AK/883B are automatically interchangeable in every procurement environment. The /883B designation is tied to SMD number 5962-89961 and has a documented 30 ohm on resistance, while the standard DG405AK is identified at 35 ohm. Check qualification, traceability, supply voltage, logic levels, and absolute maximum ratings before substitution.
Place the required bypass capacitor close to the supply pins and follow the manufacturer layout and grounding guidance. Because a fast switch can generate transient current at the controlled edges, provide a low-impedance return and decouple nearby analog stages that share the same board area. Verify control-driver rise and fall times so switching transients are not introduced by slow or unstable control signals.
合規資訊
The DG405AK/883B is associated with SMD number 5962-89961, but AEC-Q100 qualification does not apply because this is an interface IC rather than an automotive device. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status require confirmation from the manufacturer or lot documentation.