Maxim Integrated

DG405AK - Dual High-Speed 35Ohm Analog Switch | Maxim

MPN: DG405AK ✓ فعال
35 ohm Rds(on) 16-pin CERDIP Package
حداقل سفارش: 1 |

DG405AK نمای کلی

The Maxim Integrated DG405AK is a dual, high-speed analog switch with two independently controlled SPST channels, a 2:1 circuit configuration, 35 ohm on resistance, and a 16-pin CERDIP package. It is a normally open CMOS switch designed for routing analog signals where low on resistance, controlled channel matching, and fast operation are important. The DG405 family is identified as production by the manufacturer.

An analog switch is an interface IC that connects or disconnects a signal path under digital control. The DG405AK belongs to the broader analog-switch hierarchy, which includes multiplexers, demultiplexers, and CMOS switch ICs used in data acquisition, test, communications, instrumentation, and signal-routing systems. Its normally open architecture leaves each channel disconnected until the corresponding control signal activates it.

The redesigned DG405 family provides guaranteed on-resistance matching between the two switches of 2 ohm maximum and guaranteed on-resistance flatness over the signal range of 3 ohm maximum. The manufacturer also identifies a typical on resistance of 20 ohm. These characteristics help reduce channel-dependent amplitude error and distortion when the same signal is routed through different switch paths. The distributed 35 ohm value identifies the DG405AK configuration and should be checked against the operating signal range during design.

The DG405AK uses dual SPST CMOS switching elements and high-speed control logic. Two switches provide separate routing decisions rather than multiplexing a larger number of inputs through one common terminal. This arrangement is useful when a system must select between two signal paths, isolate a source from a downstream instrument, or implement a sample-and-hold acquisition network. Exact switching-time, voltage, leakage, and channel-count details must be confirmed in the manufacturer data sheet.

Typical applications include precision signal routing in data-acquisition systems, switched-capacitor filter control, audio and communications routing, automated test equipment, and laboratory instrumentation. The matched on-resistance specification is especially valuable when comparing channels in instrumentation, while the high-speed architecture suits systems that require rapid settling between measurement or routing states. External clocking, drive levels, and control timing must remain within the device's documented operating limits.

Design the surrounding circuit so that signal amplitude, bandwidth, and transient current remain compatible with the switch. Place bypass and protection components close to the supply and signal pins, and use controlled-impedance routing when signals are sensitive to reflection or crosstalk. Account for off-state isolation, charge injection, and control-logic timing when planning precision measurements or synchronous acquisition sequences.

This page combines the manufacturer's DG405 family information, package and configuration details, and practical routing guidance with a pin-compatible comparison focused on military-qualified DG405 variants. It is intended to help engineers identify the correct switch configuration, verify package compatibility, and plan the surrounding analog signal path before releasing a PCB design.

جایگزین‌های drop-in برای DG405AK — همان پکیج، سازگار پین‌به‌پین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.

DG405AK/883B

✅ جایگزین مستقیم
📦 16-CDIP
On resistance is 30 ohm versus 35 ohm for DG405AK, a 5 ohm or 14 percent reduction; adds 5962-89961 screened or military qualification.

📋 جایگزین مرجع (خارج از کاتالوگ)

DG405AK/883

✅ جایگزین مستقیم
📦 16-CDIP
Uses the same dual normally open SPST configuration and 16-pin ceramic-DIP outline, with 150 ns maximum turn-on and 100 ns maximum turn-off timing.

📋 جایگزین مرجع (خارج از کاتالوگ)

DG405AK حداکثر مقادیر مجاز و مشخصات الکتریکی

Number of Circuits 2 circuits
Multiplexer Configuration 2:1 configuration
Switch Architecture Dual SPST channels
Signal State Normally open
On Resistance 35 ohm
Typical On Resistance 20 ohm
On-Resistance Matching Between Switches 2 ohm maximum
On-Resistance Flatness Over Signal Range 3 ohm maximum
Technology CMOS analog switch
بسته‌بندی 16-pin CERDIP
Package Pitch 0.300 inch (7.62 mm)
نوع نصب Through-hole
Qualification Variant DG405AK/883B is a 5962-89961 qualified variant
Turn-On Time 150 ns maximum for DG405AK/883
Turn-Off Time 100 ns maximum for DG405AK/883
وضعیت چرخه عمر Production

راهنمای پیکربندی پین DG405AK 0.300 inch (7.62 mm)

پیکربندی پین برای DG405AK (پکیج 0.300 inch (7.62 mm)). شماره‌گذاری پایه‌ها، عملکردها و نمودارهای اتصال در دیتاشیت سازنده تعریف شده است. برای footprint دقیق و دستورالعمل‌های لحیم‌کاری به آن مراجعه کنید.

نمودار پین‌آوت پکیج 0.300 inch (7.62 mm) برای DG405AK

داده پین‌آوت تفصیلی موجود نیست برای DG405AK.

به دیتاشیت برای پیکربندی کامل پین‌ها.

کاربردهای معمول

DG405AK مناسب است برای 6 کاربردs: Precision Data-Acquisition Routing, Switched-Capacitor Filter Control, Automated Test Equipment, Audio Signal Routing, Communications Signal Isolation, Laboratory Instrumentation.

📊

Precision Data-Acquisition Routing

The DG405AK fits precision acquisition routing because its two normally open SPST channels can isolate or connect separate analog sources while the family guarantees on-resistance matching of 2 ohm maximum. This matching helps limit channel-dependent gain errors when the same measurement path is calibrated across multiple inputs. The typical 20 ohm on resistance also supports practical acquisition front ends. Confirm signal bandwidth, charge injection, leakage, and settling behavior against the manufacturer data sheet before finalizing the front end.

⚡

Switched-Capacitor Filter Control

The DG405AK can control the switching elements in a switched-capacitor filter when the required operating frequency and settling interval fit the device's documented limits. Its dual SPST arrangement supports independent charge-transfer paths, while the DG405 family's typical 20 ohm on resistance can influence the effective settling behavior of each capacitor network. Design the control waveform to avoid overlap during charge transfer and include switch capacitance and charge injection in the filter simulation.

🧪

Automated Test Equipment

DG405AK suits automated test equipment that needs to route one of two analog conditions into a measurement chain. The guaranteed 2 ohm maximum matching between switches helps maintain repeatability when a path is switched during calibration or diagnostic sequencing. The 16-pin CERDIP package also supports legacy and rugged through-hole assemblies. Verify isolation, leakage, control levels, and qualification requirements at the system level, particularly where long test cables can introduce additional noise and capacitance.

🎧

Audio Signal Routing

The DG405AK can route low-frequency audio signals between two paths where normally open SPST behavior and controlled on resistance are important. Its 35 ohm identified on resistance and the family's 20 ohm typical value can be included in the signal-path loss budget, while the 2 ohm maximum matching helps avoid audible channel imbalance in balanced routing architectures. The designer should still check distortion, off-state isolation, ground leakage, and bandwidth against the particular preamplifier and source impedance.

🌐

Communications Signal Isolation

DG405AK is applicable to communications equipment that requires a normally open analog isolation path between a transmitter, receiver, or test network. Two independent channels provide routing flexibility without forcing a common multiplexed node, while the high-speed switch family is intended for rapid signal-path changes. Check the maximum signal voltage, supply requirements, control timing, insertion loss, and isolation at the operating frequency. Board-level EMI performance will also depend on impedance matching and grounding outside the IC.

🔬

Laboratory Instrumentation

The DG405AK can select or disconnect signals in laboratory instruments where channel consistency and ceramic-DIP construction are useful. The DG405 family's guaranteed on-resistance matching of 2 ohm maximum reduces path variation between the two switches, while on-resistance flatness of 3 ohm maximum supports predictable behavior across the specified signal range. For precision meters and source-measure systems, validate leakage, noise, charge injection, and settling time with the complete front-end network rather than relying on the on resistance alone.

خلاصه محصولات پیشنهادی

DG405AK/883B Qualified dual-switch configuration for demanding acquisition equipment استفاده‌شده در: Precision Data-Acquisition Routing, Switched-Capacitor Filter Control, Automated Test Equipment, Audio Signal Routing, Communications Signal Isolation, Laboratory Instrumentation DG405AK/883 High-speed dual-SPST configuration with documented switching timing استفاده‌شده در: Precision Data-Acquisition Routing, Switched-Capacitor Filter Control, Automated Test Equipment, Audio Signal Routing, Communications Signal Isolation, Laboratory Instrumentation
What is the DG405AK?
The DG405AK is a dual, high-speed CMOS analog switch with two normally open SPST channels, a 2:1 configuration, and a 16-pin CERDIP package. It is intended for switching analog signals rather than power rails. According to the Maxim Integrated DG405 product page, the improved family guarantees on-resistance matching between switches of 2 ohm maximum and on-resistance flatness over the signal range of 3 ohm maximum.
What are the key specifications of DG405AK that engineers should know?
The DG405AK combines two normally open SPST analog-switch channels in a 16-pin CERDIP package. Its identified on resistance is 35 ohm, while the improved DG405 family provides a typical on resistance of 20 ohm. Maxim Integrated specifies on-resistance matching between switches at 2 ohm maximum and on-resistance flatness over the signal range at 3 ohm maximum.
Where can I download the DG405AK datasheet PDF?
The official DG405AK datasheet is available through the Maxim Integrated DG405 product page at analog.com. That page links the DG405 family Data Sheet, Rev. 2, together with product-selection and documentation resources. Use the manufacturer data sheet for the authoritative DG405AK pin assignment, electrical limits, switching timing, and recommended operating conditions.
Where can I find the DG405AK pinout?
Use the pin-description table and package drawing in the Maxim Integrated DG405 Data Sheet to locate the DG405AK pinout. The part is packaged in a 16-pin CERDIP outline, and the manufacturer data sheet is the correct reference for control inputs, drain and source terminals, supply connections, and exposed package information. Confirm the ceramic-DIP numbering directly before assigning PCB tracks.
Is DG405AK suitable for high-speed signal routing?
Yes, DG405AK is designed as a high-speed dual analog switch. The related DG405AK/883 military variant is identified with a turn-on time of 150 ns maximum and turn-off time of 100 ns maximum. Actual usable bandwidth still depends on the complete analog path, including source and load impedance, switch capacitance, layout, and the frequency-dependent behavior of the on resistance.
What is the difference between DG405AK and DG405AK/883B?
The DG405AK is the commercial ordering designation shown for the 16-pin CERDIP switch, while DG405AK/883B is a screened or military-qualified designation associated with SMD number 5962-89961. The DG405AK/883B listing identifies 30 ohm on resistance versus 35 ohm for DG405AK, a difference of 5 ohm or approximately 14 percent, while both use the 16-pin CDIP/CERDIP format.
DG405AK vs DG405AK/883B - which is better for military equipment?
DG405AK/883B is the better choice when the procurement specification requires SMD number 5962-89961 or the associated screened or military qualification. DG405AK is appropriate for applications that need the standard commercial DG405AK configuration. Both retain dual SPST, normally open switching behavior and the 16-pin ceramic-DIP package, so the qualification requirement is the principal selection criterion.
When should I choose DG405AK over another dual analog switch?
Choose DG405AK when the design requires two normally open SPST channels, the DG405 family's guaranteed channel matching of 2 ohm maximum, on-resistance flatness of 3 ohm maximum, and a 16-pin CERDIP footprint. Consider a smaller surface-mount switch when board area is the priority, or another switch family when its voltage rating, bandwidth, charge injection, or logic levels better match the signal path.
Is DG405AK suitable for switched-capacitor filtering?
Yes, DG405AK can fit switched-capacitor filtering when the required settling time and signal amplitude remain within its operating limits. The DG405AK/883 variant has a stated turn-off time of 100 ns maximum and turn-on time of 150 ns maximum. Filter design should also account for switch on resistance, capacitance, charge injection, control overlap, and clock timing.
What is the best drop-in replacement for DG405AK?
DG405AK/883B is the closest documented drop-in option because it retains the dual normally open SPST configuration and 16-pin ceramic-DIP package. Its listed on resistance is 30 ohm compared with 35 ohm for DG405AK. Final substitution still requires checking the complete manufacturer data sheet for supply voltage, control levels, switching timing, leakage, and qualification requirements.
Can DG405AK/883 replace DG405AK?
DG405AK/883B can replace DG405AK when the original circuit uses the compatible 16-pin ceramic-DIP footprint and does not conflict with the military qualification or ordering requirements. Its identified 30 ohm on resistance is 5 ohm lower than the DG405AK's 35 ohm value. Verify control polarity, supply voltage, absolute maximum ratings, and timing before approving the substitution.
What can replace DG405AK?
The most direct documented replacement is DG405AK/883B because it preserves the dual SPST, normally open switch function and 16-pin ceramic-DIP package. It also reduces the listed on resistance from 35 ohm to 30 ohm. DG411 and DG412 are mentioned as potential alternatives for designs needing faster switching or lower resistance, but they should not be treated as footprint-compatible replacements without package and pin verification.
What is the Vishay equivalent for DG405AK?
The Vishay Siliconix DG405AK is the same ordering code listed for the dual 35 ohm, 2:1, 16-CERDIP analog switch. The component has historical Intersil and Maxim Integrated sourcing associations, so procurement teams should verify the current manufacturer label, screening status, date code, and traceability documentation. The DG405AK/883B remains a distinct military-qualified ordering designation.
Where to buy DG405AK online?
Use the Request a Quote form on this page to request DG405AK availability, current lead time, and minimum order quantity. The DG405AK is listed in production by Maxim Integrated, and authorized distribution records include the 16-pin CERDIP configuration. Provide the required grade and screening details in the request so the quoted part matches the intended assembly and procurement specification.
What is the price of DG405AK?
Current DG405AK pricing depends on quantity, sourcing grade, and requested delivery terms, so use the Request a Quote form on this page for a transaction-ready quotation. Quote requests should specify the standard DG405AK or the 5962-89961 DG405AK/883B designation, quantity, target date, and any required inspection or traceability documentation.
What is the lead time for DG405AK?
Submit a DG405AK request through the Request a Quote form on this page to obtain the current manufacturer lead time, available stock, and minimum order quantity. The manufacturer lists the DG405 family as production, but production status does not by itself guarantee a fixed allocation or immediate shipment for a specific grade and quantity.
Is DG405AK in stock?
DG405AK inventory changes by quantity and ordering code, so use the Request a Quote form on this page for a current stock response. Include the desired package and grade in the request: DG405AK denotes the standard ceramic-DIP part, while DG405AK/883B identifies the 5962-89961 qualified variant. The form can return the latest availability and lead-time information.

داده‌های مرجع مهندسی برای DG405AK — مقایسه، راهنمای طراحی و اطلاعات انطباق.

راهنمای انتخاب

Choose the standard DG405AK for commercial or industrial designs that require two normally open SPST channels, the DG405 family's channel-matching and flatness guarantees, and a 16-pin CERDIP footprint. Select DG405AK/883B when the assembly requires SMD number 5962-89961 or when its documented 30 ohm on resistance is preferable to the standard part's 35 ohm value. DG405AK/883 is useful when the design needs an explicitly documented 150 ns maximum turn-on and 100 ns maximum turn-off. Do not treat DG411 or DG412 as unconditional drop-in replacements: although they are identified as alternatives for faster or lower-resistance designs, package and pin compatibility must be confirmed before board substitution.

مقایسه با جایگزین‌ها

پارامتر این محصول DG405AK/883B DG405AK/883
Brand Maxim Integrated Maxim Integrated Maxim Integrated
Package 16-pin CERDIP 16-CDIP 16-CDIP
Number of Circuits 2 circuits 2 circuits 2 circuits
Switch Configuration Dual SPST Dual SPST Dual SPST
Qualification Designation Standard DG405AK 5962-89961 /883 designation
Signal State Normally open Normally open Normally open
Mounting Type Through-hole Through-hole Through-hole

تفاوت‌های کلیدی

  • Lower documented on resistance in the qualified ordering code (در مقابلDG405AK/883B)
  • Military-qualified designation for controlled procurement (در مقابلDG405AK)
  • Documented high-speed transition timing (در مقابلDG405AK)

یادداشت‌های طراحی

Model the switched path as a frequency-dependent resistance rather than using only the 35 ohm DC value. Include source and load impedance, switch capacitance, and the complete routing geometry when estimating attenuation or settling time. For fast edges, keep the route short and provide a continuous return path so switching current does not couple into sensitive analog nodes.

Assign the PCB footprint from the manufacturer package drawing rather than treating every ceramic DIP as electrically or mechanically interchangeable. Confirm row spacing, lead pitch, body dimensions, and pin-one orientation. Maintain adequate clearance around the 16-pin CERDIP and keep analog signal traces away from digital control nets to reduce switching crosstalk.

Do not infer that DG405AK, DG405AK/883, and DG405AK/883B are automatically interchangeable in every procurement environment. The /883B designation is tied to SMD number 5962-89961 and has a documented 30 ohm on resistance, while the standard DG405AK is identified at 35 ohm. Check qualification, traceability, supply voltage, logic levels, and absolute maximum ratings before substitution.

Place the required bypass capacitor close to the supply pins and follow the manufacturer layout and grounding guidance. Because a fast switch can generate transient current at the controlled edges, provide a low-impedance return and decouple nearby analog stages that share the same board area. Verify control-driver rise and fall times so switching transients are not introduced by slow or unstable control signals.

اطلاعات انطباق

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
بدون سرب
Unknown
بدون هالوژن
Unknown
مواد معدنی درگیری
Unknown

The DG405AK/883B is associated with SMD number 5962-89961, but AEC-Q100 qualification does not apply because this is an interface IC rather than an automotive device. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status require confirmation from the manufacturer or lot documentation.

جستجوهای مرتبط

DG405AK datasheet DG405AK datasheet pdf DG405AK pinout DG405AK specifications DG405AK 35 ohm analog switch DG405AK CERDIP package DG405AK equivalent DG405AK drop-in replacement DG405AK vs DG405AK/883B Maxim Integrated DG405AK DG405AK price DG405AK stock and lead time DG405AK high-speed signal routing what can replace DG405AK

قطعات و اصطلاحات مرتبط

Maxim Integrated DG405AK DG405AK/883 DG405AK/883B DG405 DG411 DG412 analog switch CMOS analog switch SPST switch normally open switch multiplexer demultiplexer interface IC on resistance on-resistance matching on-resistance flatness turn-on time turn-off time signal routing data acquisition switched-capacitor filter 5962-89961 CERDIP-16 CDIP-16
استعلام قیمت سریع RFQ
جزئیات کامل را پر کنید — تیم فروش ما ظرف 24 ساعت پاسخ خواهد داد
شماره قطعه سازنده بسته‌بندی QTY قیمت هدف قیمت کل
✓
استعلام قیمت ارسال شد!

ظرف ۲۴ ساعت به ایمیل شما پاسخ خواهیم داد

1
درخواست قیمت ارسال شد
2
استعلام دریافت شد
3
سفارش ثبت شد
4
پرداخت
5
ارسال شد
6
تحویل داده شد
مشاهده جزئیات RFQ