DG405AK - Dual High-Speed 35Ohm Analog Switch | Maxim
MPN: DG405AK ✓ פעילDG405AK סקירה
An analog switch is an interface IC that connects or disconnects a signal path under digital control. The DG405AK belongs to the broader analog-switch hierarchy, which includes multiplexers, demultiplexers, and CMOS switch ICs used in data acquisition, test, communications, instrumentation, and signal-routing systems. Its normally open architecture leaves each channel disconnected until the corresponding control signal activates it.
The redesigned DG405 family provides guaranteed on-resistance matching between the two switches of 2 ohm maximum and guaranteed on-resistance flatness over the signal range of 3 ohm maximum. The manufacturer also identifies a typical on resistance of 20 ohm. These characteristics help reduce channel-dependent amplitude error and distortion when the same signal is routed through different switch paths. The distributed 35 ohm value identifies the DG405AK configuration and should be checked against the operating signal range during design.
The DG405AK uses dual SPST CMOS switching elements and high-speed control logic. Two switches provide separate routing decisions rather than multiplexing a larger number of inputs through one common terminal. This arrangement is useful when a system must select between two signal paths, isolate a source from a downstream instrument, or implement a sample-and-hold acquisition network. Exact switching-time, voltage, leakage, and channel-count details must be confirmed in the manufacturer data sheet.
Typical applications include precision signal routing in data-acquisition systems, switched-capacitor filter control, audio and communications routing, automated test equipment, and laboratory instrumentation. The matched on-resistance specification is especially valuable when comparing channels in instrumentation, while the high-speed architecture suits systems that require rapid settling between measurement or routing states. External clocking, drive levels, and control timing must remain within the device's documented operating limits.
Design the surrounding circuit so that signal amplitude, bandwidth, and transient current remain compatible with the switch. Place bypass and protection components close to the supply and signal pins, and use controlled-impedance routing when signals are sensitive to reflection or crosstalk. Account for off-state isolation, charge injection, and control-logic timing when planning precision measurements or synchronous acquisition sequences.
This page combines the manufacturer's DG405 family information, package and configuration details, and practical routing guidance with a pin-compatible comparison focused on military-qualified DG405 variants. It is intended to help engineers identify the correct switch configuration, verify package compatibility, and plan the surrounding analog signal path before releasing a PCB design.
חלופות תחליף ישיר עבור DG405AK — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.
DG405AK/883B
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
DG405AK/883
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
DG405AK דירוגים מרביים ומאפיינים חשמליים
| Number of Circuits | 2 circuits |
| Multiplexer Configuration | 2:1 configuration |
| Switch Architecture | Dual SPST channels |
| Signal State | Normally open |
| On Resistance | 35 ohm |
| Typical On Resistance | 20 ohm |
| On-Resistance Matching Between Switches | 2 ohm maximum |
| On-Resistance Flatness Over Signal Range | 3 ohm maximum |
| Technology | CMOS analog switch |
| מארז | 16-pin CERDIP |
| Package Pitch | 0.300 inch (7.62 mm) |
| סוג הרכבה | Through-hole |
| Qualification Variant | DG405AK/883B is a 5962-89961 qualified variant |
| Turn-On Time | 150 ns maximum for DG405AK/883 |
| Turn-Off Time | 100 ns maximum for DG405AK/883 |
| סטטוס מחזור חיים | Production |
מדריך תצורת פינים של DG405AK 0.300 inch (7.62 mm)
תצורת פינים עבור DG405AK (מארזת 0.300 inch (7.62 mm)). מספרי פינים, פונקציות ותרשימי חיבורים מוגדרים ב-Datasheet של היצרן. יש לעיין בו לקבלת ה-footprint המדויק והנחיות הלחמה.
אין נתוני פריסת פינים מפורטים עבור DG405AK.
עיינו ב- גיליון נתונים עבור תצורת פינים מלאה.
יישומים טיפוסיים
DG405AK מתאים עבור 6 יישוםs: Precision Data-Acquisition Routing, Switched-Capacitor Filter Control, Automated Test Equipment, Audio Signal Routing, Communications Signal Isolation, Laboratory Instrumentation.
Precision Data-Acquisition Routing
The DG405AK fits precision acquisition routing because its two normally open SPST channels can isolate or connect separate analog sources while the family guarantees on-resistance matching of 2 ohm maximum. This matching helps limit channel-dependent gain errors when the same measurement path is calibrated across multiple inputs. The typical 20 ohm on resistance also supports practical acquisition front ends. Confirm signal bandwidth, charge injection, leakage, and settling behavior against the manufacturer data sheet before finalizing the front end.
מומלץ
Switched-Capacitor Filter Control
The DG405AK can control the switching elements in a switched-capacitor filter when the required operating frequency and settling interval fit the device's documented limits. Its dual SPST arrangement supports independent charge-transfer paths, while the DG405 family's typical 20 ohm on resistance can influence the effective settling behavior of each capacitor network. Design the control waveform to avoid overlap during charge transfer and include switch capacitance and charge injection in the filter simulation.
מומלץ
Automated Test Equipment
DG405AK suits automated test equipment that needs to route one of two analog conditions into a measurement chain. The guaranteed 2 ohm maximum matching between switches helps maintain repeatability when a path is switched during calibration or diagnostic sequencing. The 16-pin CERDIP package also supports legacy and rugged through-hole assemblies. Verify isolation, leakage, control levels, and qualification requirements at the system level, particularly where long test cables can introduce additional noise and capacitance.
מומלץ
Audio Signal Routing
The DG405AK can route low-frequency audio signals between two paths where normally open SPST behavior and controlled on resistance are important. Its 35 ohm identified on resistance and the family's 20 ohm typical value can be included in the signal-path loss budget, while the 2 ohm maximum matching helps avoid audible channel imbalance in balanced routing architectures. The designer should still check distortion, off-state isolation, ground leakage, and bandwidth against the particular preamplifier and source impedance.
מומלץ
Communications Signal Isolation
DG405AK is applicable to communications equipment that requires a normally open analog isolation path between a transmitter, receiver, or test network. Two independent channels provide routing flexibility without forcing a common multiplexed node, while the high-speed switch family is intended for rapid signal-path changes. Check the maximum signal voltage, supply requirements, control timing, insertion loss, and isolation at the operating frequency. Board-level EMI performance will also depend on impedance matching and grounding outside the IC.
מומלץ
Laboratory Instrumentation
The DG405AK can select or disconnect signals in laboratory instruments where channel consistency and ceramic-DIP construction are useful. The DG405 family's guaranteed on-resistance matching of 2 ohm maximum reduces path variation between the two switches, while on-resistance flatness of 3 ohm maximum supports predictable behavior across the specified signal range. For precision meters and source-measure systems, validate leakage, noise, charge injection, and settling time with the complete front-end network rather than relying on the on resistance alone.
מומלץ
סיכום מוצרים מומלצים
נתוני עזר הנדסיים עבור DG405AK — השוואה, הנחיות תכנון ומידע על תאימות.
מדריך בחירה
השוואה עם חלופות
| פרמטר | מוצר זה | DG405AK/883B | DG405AK/883 |
|---|---|---|---|
| Brand | Maxim Integrated | Maxim Integrated | Maxim Integrated |
| Package | 16-pin CERDIP | 16-CDIP | 16-CDIP |
| Number of Circuits | 2 circuits | 2 circuits | 2 circuits |
| Switch Configuration | Dual SPST | Dual SPST | Dual SPST |
| Qualification Designation | Standard DG405AK | 5962-89961 | /883 designation |
| Signal State | Normally open | Normally open | Normally open |
| Mounting Type | Through-hole | Through-hole | Through-hole |
מבדילים עיקריים
- Lower documented on resistance in the qualified ordering code (לעומתDG405AK/883B)
- Military-qualified designation for controlled procurement (לעומתDG405AK)
- Documented high-speed transition timing (לעומתDG405AK)
הערות תכנון
Model the switched path as a frequency-dependent resistance rather than using only the 35 ohm DC value. Include source and load impedance, switch capacitance, and the complete routing geometry when estimating attenuation or settling time. For fast edges, keep the route short and provide a continuous return path so switching current does not couple into sensitive analog nodes.
Assign the PCB footprint from the manufacturer package drawing rather than treating every ceramic DIP as electrically or mechanically interchangeable. Confirm row spacing, lead pitch, body dimensions, and pin-one orientation. Maintain adequate clearance around the 16-pin CERDIP and keep analog signal traces away from digital control nets to reduce switching crosstalk.
Do not infer that DG405AK, DG405AK/883, and DG405AK/883B are automatically interchangeable in every procurement environment. The /883B designation is tied to SMD number 5962-89961 and has a documented 30 ohm on resistance, while the standard DG405AK is identified at 35 ohm. Check qualification, traceability, supply voltage, logic levels, and absolute maximum ratings before substitution.
Place the required bypass capacitor close to the supply pins and follow the manufacturer layout and grounding guidance. Because a fast switch can generate transient current at the controlled edges, provide a low-impedance return and decouple nearby analog stages that share the same board area. Verify control-driver rise and fall times so switching transients are not introduced by slow or unstable control signals.
מידע על תאימות
The DG405AK/883B is associated with SMD number 5962-89961, but AEC-Q100 qualification does not apply because this is an interface IC rather than an automotive device. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status require confirmation from the manufacturer or lot documentation.