ICS574MI - 160 MHz PLL Zero-Delay Fanout Buffer | Renesas
MPN: ICS574MI ✓ 啟用中ICS574MI 概覽
A zero-delay buffer is a clock-and-timing integrated circuit that uses phase-locked-loop technology to reproduce an input clock at its outputs with nearly zero net propagation delay. It belongs to the fanout-buffer hierarchy within clock and timing ICs, where PLL-based devices trade additional internal complexity for improved edge alignment and predictable output skew. This makes the ICS574MI suitable for systems in which several circuits must receive a related clock without accumulating cumulative trace-delay differences.
According to the Renesas 574 Datasheet, the ICS574 is based on proprietary low-jitter PLL techniques. The documented operating point includes speeds up to 160 MHz at 3.3 V, with four low-skew outputs. When one output is returned directly to the FBIN input, the rising edge of each output can be aligned with the rising edge of the feedback signal, allowing the feedback path to compensate for clock distribution delay around the board.
Typical uses include processor and FPGA clock distribution, memory-interface clock fanout, backplane clock replication, communications equipment, and test-and-measurement systems. The 1:4 ratio reduces the number of separate clock-driver channels required when four destinations need a common timing reference. Because a fanout buffer does not regenerate data content, its outputs are intended for clock or low-fanout control signals rather than high-speed data traffic.
The key design consideration is output loading and board topology. Short, matched traces, terminated clock networks, and appropriate supply decoupling help preserve edge quality and limit skew. When cascading multiple fanout devices, engineers should verify cumulative jitter, output-to-output skew, duty-cycle distortion, and loading with the complete clock distribution network rather than relying on individual device specifications.
直接替換替代品,適用於 ICS574MI — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
574MILF
✅ 直接替換📋 參考替代品(不在目錄中)
ICS574MI 規格
| Device Type | Fanout Buffer (Distribution), Zero Delay Buffer |
| Architecture | PLL-based zero-delay buffer |
| Maximum Frequency | 160 MHz |
| Number of Circuits | 1 |
| 輸出數量 | 4 |
| Input to Output Ratio | 1:4 |
| Input Logic Level | CMOS |
| Output Logic Level | CMOS |
| Documented Supply Voltage | 3.3 V |
| Propagation Delay | Zero delay (PLL compensated) |
| Output Skew | Low skew |
| Jitter | Low jitter |
| Feedback Compensation | FBIN feedback input for output-edge alignment |
| 封裝 | 8-SOIC, 0.154 inch body width, 3.90 mm width |
| 安裝類型 | Surface mount |
ICS574MI 8-soic, 0.154 inch body width, 3.90 mm width 腳位配置指南
ICS574MI(8-soic, 0.154 inch body width, 3.90 mm width 封裝)的腳位配置。 腳位編號、功能與連接圖定義於製造商資料手冊中。請參閱該手冊以取得確切的封裝尺寸與焊接指引。
無詳細腳位定義資料: ICS574MI.
請參閱 資料表 以查看完整腳位配置。
典型應用
ICS574MI 適用於 6 應用s: FPGA Clock Fanout, Processor and SoC Clock Distribution, Memory-Interface Clock Fanout, Backplane and Communications Clock Replication, Test and Measurement Clock Fanout, Synchronous Data Acquisition Systems.
FPGA Clock Fanout
The ICS574MI fits FPGA clock-distribution trees because its PLL-based zero-delay function can align four output edges to a feedback reference rather than allowing trace delay to accumulate independently on each branch. Operating up to 160 MHz at 3.3 V, it is suitable for feeding several FPGA clock resources from one source clock. Route a controlled-impedance clock network, connect one output to FBIN, and keep matched branches electrically similar. The main benefit is reduced timing uncertainty at the receiving devices; the trade-off is that PLL loop behavior, input jitter, and output loading must be verified with the complete board rather than treated as ideal clock copies.
推薦
Processor and SoC Clock Distribution
The ICS574MI can distribute a common reference clock to a processor, SoC, memory controller, and peripheral blocks when four destinations must launch from a tightly related edge. Its 1:4 fanout ratio avoids placing four separate drivers near the source, and the FBIN path allows the PLL to compensate for board propagation delay. Use it only where the clock rate remains within the documented 160 MHz limit at 3.3 V. Keep the source slew rate clean, isolate the feedback route from noisy loads, and verify duty-cycle distortion at each receiver. This arrangement improves edge alignment but adds a PLL-based device and feedback loop that must be validated during timing sign-off.
推薦
Memory-Interface Clock Fanout
The ICS574MI is appropriate for clock distribution to memory-interface logic when a single source must reach several receivers with controlled relative timing. Its four low-skew CMOS outputs can feed address, command, or data-path clock domains that require a common launch relationship. The PLL feedback topology helps compensate for unequal clock-trace delays that would otherwise shift setup and hold margins between endpoints. Place the device near the clock source, use series damping where needed, and keep the FBIN trace short and shielded from switching-current paths. Because memory interfaces are sensitive to duty-cycle distortion and jitter, validate the design with realistic loading and the highest specified operating frequency.
推薦
Backplane and Communications Clock Replication
In communications equipment, the ICS574MI can replicate one reference clock into four outputs for protocol engines, transceivers, and interface controllers distributed across a chassis or backplane. The 160 MHz capability accommodates many legacy parallel-bus and fabric-clock applications, while FBIN feedback addresses the skew accumulated through connectors and board routing. Keep each output on a separate, impedance-controlled branch, and place termination at the appropriate endpoint. The device is best suited to clock signals rather than high-speed data, and its benefits depend on disciplined board topology. Compare end-to-end skew and jitter at the connector rather than relying only on the chip's nominal output timing.
推薦
Test and Measurement Clock Fanout
The ICS574MI can fan a laboratory or instrument clock into four synchronized channels, giving multiple acquisition, conversion, or processing sections a common timing reference. Its PLL-based alignment helps keep channel-to-channel skew predictable across a multi-board instrument, which is valuable for time-domain measurements and synchronous sampling. Use short output routes, matched input/output loading, and a single-point reference concept to minimize connector-induced delay differences. The trade-off is that a PLL can add jitter and the zero-delay function does not eliminate all trace skew by itself. Characterize the complete distribution path with the intended instrument settings and verify that the 160 MHz operating limit covers the fastest clock mode required.
推薦
Synchronous Data Acquisition Systems
The ICS574MI is useful when several converters or digital processors must sample from a common clock edge in a synchronous acquisition system. Four low-skew outputs provide clock copies without replicating the source driver at every load, and the feedback path lets the PLL align output edges with the distributed network. Keep the clock network free of aggressive capacitive stubs and confirm that each output drives a stable, well-terminated load. The device improves relative edge placement but cannot compensate for random jitter already present on the source clock. Use a low-jitter reference upstream, provide local supply bypassing, and measure skew across the complete acquisition chain before treating the timing margin as fixed.
推薦
推薦產品摘要
工程參考資料,適用於 ICS574MI — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | 574MILF |
|---|---|---|
| Package | 8-SOIC, 0.154 inch body width, 3.90 mm width | 8-SOIC |
| Brand | Renesas Electronics | Renesas Electronics |
| Device Type | Fanout Buffer (Distribution), Zero Delay Buffer | 574-family zero-delay fanout buffer |
主要差異化特點
- Feedback-aligned four-output clock distribution (對比574MILF)
- Single-package 1:4 fanout (對比574MILF)
- Low-skew and low-jitter PLL architecture (對比574MILF)
設計說明
Treat the ICS574MI outputs as a controlled clock network rather than ordinary logic traces. Use short, matched routes with continuous reference planes, avoid long stubs, and place the FBIN connection as a dedicated feedback path. Connect one output back to FBIN following the manufacturer topology so the PLL can compensate for propagation delay in the distributed clock network. Confirm the physical dimensions and pin assignments against the Renesas 574 Datasheet before releasing the PCB layout.
Keep output loading within the device's recommended range and measure edge rate, duty-cycle distortion, and skew at the far end of the longest clock branch. Series damping or source termination may be required when traces are long or receivers have high capacitance. Validate the complete network with realistic loading because PLL compensation can correct systematic propagation delay but cannot remove random jitter, crosstalk, or reflections caused by poor routing.
Place the supply-decoupling capacitor close to the device and provide a low-impedance return path for each clock output. Follow the capacitor values and layout recommended in the Renesas 574 Datasheet when they are specified. Do not assume that the 3.3 V operating point permits any supply tolerance; confirm the full input-voltage range and maximum operating frequency from the manufacturer timing and electrical tables before release.
A common implementation error is treating a zero-delay buffer like an ideal logic inverter with no feedback alignment. Another is routing the clock outputs as long, unterminated traces that amplify noise and distortion. Use a clean source clock, verify the PLL feedback topology, keep the device within its documented 160 MHz limit, and test skew across all four destinations rather than measuring only at the device pins.
合規資訊
The Renesas 574 Datasheet and distributor listings do not establish RoHS, REACH, AEC-Q100, halogen-free, or conflict-minerals status for this order code. Confirm current declarations with the manufacturer before making a compliance claim.