INA105KUG4 - 1MHz Unity-Gain Differential Amplifier | Texas Instruments
MPN: INA105KUG4 ✓ 啟用中INA105KUG4 概覽
A differential amplifier measures the voltage difference between two input signals while rejecting signals common to both inputs. This INA105 unity-gain device belongs to the differential-amplifier category, where it sits between precision operational amplifiers and instrumentation-amplifier signal-conditioning circuits. Its fixed unity gain makes it useful when the source already provides the required scaling and the system primarily needs accurate differential sensing.
The principal feature of the INA105KUG4 is its integrated gain-setting network. Laser trimming provides accurate nominal gain and consistent resistor tracking. Because the network is formed on the same monolithic die as the operational amplifier, it eliminates the need for a discrete precision resistor pair in applications where equal-gain differential conversion is required.
The manufacturer describes the INA105 as a monolithic Gain = 1 differential amplifier built around a precision operational amplifier and an on-chip metal-film resistor network. Laser trimming supports accurate gain and common-mode rejection, while the matched temperature coefficient of the network helps preserve performance as temperature changes. The specified 1 MHz -3 dB bandwidth provides useful speed for instrumentation and industrial signal chains.
Typical uses include bridge-sensor signal conditioning, current-sense amplifier output filtering, differential measurement interfaces, and analog front ends that compare two sensor channels. The 3 V/µs slew rate supports accurate reproduction of moderate-frequency differential waveforms, while unity gain lets engineers retain the source voltage without introducing an additional gain error.
Layout should preserve the differential nature of the device by routing input pairs as closely as practical, minimizing parasitic mismatches between the two signal paths. The 8-pin SOIC package also requires adequate decoupling and careful grounding around the reference and supply pins. Review the pin-description and typical-application diagrams in the manufacturer datasheet before assigning PCB tracks.
This product page combines the manufacturer specifications, package information, sourcing guidance, drop-in alternatives, comparison parameters, and practical design notes. It is intended to help engineers determine whether the INA105KUG4's fixed unity gain, differential architecture, bandwidth, slew rate, and integrated precision network fit a particular instrumentation or signal-conditioning design.
直接替換替代品,適用於 INA105KUG4 — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: INA105KUG4 (相同外形與佔位) — 差異在於 Mounting Type, Package.
INA105U
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
INA105KP
✅ 直接替換 ⚠️ 規格未經驗證聯絡詢價
查看資料表 →INA105UA
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
AD8271BRZ
✅ 直接替換📋 參考替代品(不在目錄中)
AD8210JRZ
✅ 直接替換📋 參考替代品(不在目錄中)
INA105KUG4 最大額定值與電氣特性
| Amplifier Type | Monolithic unity-gain differential amplifier |
| Nominal Gain | 1 V/V |
| Number of Circuits | 1 circuit |
| -3 dB Bandwidth | 1 MHz |
| Slew Rate | 3 V/µs |
| Internal Amplifier | Precision operational amplifier |
| Gain Network | On-chip metal-film resistor network |
| Network Calibration | Laser trimmed |
| 封裝 | 8-pin SOIC, 3.90 mm width |
| 安裝類型 | Surface mount |
INA105KUG4 8-pin soic, 3.90 mm width 腳位配置指南
INA105KUG4(8-pin soic, 3.90 mm width 封裝)的腳位配置。 此類比元件具有輸入、輸出與電源腳位。偏移歸零、補償與致能腳位配置請參閱製造商資料表。適用於訊號調理與放大器電路。
無詳細腳位定義資料: INA105KUG4.
請參閱 資料表 以查看完整腳位配置。
典型應用
INA105KUG4 適用於 6 應用s: Bridge-Sensor Signal Conditioning, Current-Measurement Front End, Differential Voltage Measurement, Industrial Sensor Interface, Audio and Analog Difference Sensing, Portable Instrument Signal Conditioning.
Bridge-Sensor Signal Conditioning
The INA105KUG4 is well suited to converting the small differential output of a resistive bridge into a single-ended measurement signal. Its unity-gain architecture preserves the bridge differential while its laser-trimmed metal-film network supports accurate gain and high common-mode rejection. The 1 MHz -3 dB bandwidth handles sensors whose mechanical or thermal response falls well below that limit, while the 3 V/µs slew rate permits rapid output transitions. The bridge excitation, input common-mode voltage, and allowable output swing must remain inside the device operating limits.
推薦
Current-Measurement Front End
The INA105KUG4 can form the differential input stage of a current-measurement front end when a shunt or current-sense amplifier presents two closely related voltage signals. A fixed gain of 1 V/V avoids adding another scaling stage, and the integrated precision resistor network reduces mismatch between the two input paths. With a 1 MHz bandwidth and 3 V/µs slew rate, the circuit can process moderate-bandwidth current transients. Input filtering, shunt impedance, and common-mode limits should be evaluated before operation.
推薦
Differential Voltage Measurement
The INA105KUG4 is appropriate when an instrumentation system must compare two voltages rather than measure either one against ground. The differential architecture rejects common-mode disturbance, while unity gain keeps the measured difference at its original scale for downstream conversion. Its 1 MHz -3 dB bandwidth supports signal frequencies below that level, and the 3 V/µs slew rate limits large-signal distortion for faster transitions. System designers should verify source impedances, input bias-current effects, and output headroom.
推薦
Industrial Sensor Interface
The INA105KUG4 can serve as the analog interface between a pair of industrial sensor outputs and a downstream acquisition system. Its fixed unity gain reduces calibration complexity, while the monolithic resistor network avoids the component-count and tolerance burden of a discrete difference amplifier. The 1 MHz bandwidth gives adequate speed for many process-control sensors, and common-mode rejection helps suppress shared industrial interference. Protection, isolation, and surge requirements should be handled separately from the amplifier itself.
推薦
Audio and Analog Difference Sensing
The INA105KUG4 can compare two low-level analog voltages when a balanced source requires differential extraction. The unity-gain network avoids additional gain coloration in the signal path, and the integrated trimming supports repeatable channel matching. Its 1 MHz bandwidth covers much of the audible range and extends into low-frequency measurement instrumentation, while the 3 V/µs slew rate supports normal audio-rate transients. Common-mode headroom, output swing, and noise performance should be confirmed for the specific source impedance.
推薦
Portable Instrument Signal Conditioning
The INA105KUG4 is suitable for portable instrumentation that compares two sensor channels within a compact 8-pin SOIC footprint. Its monolithic unity-gain network reduces external component count, which assists board-space and assembly goals. A 1 MHz -3 dB bandwidth is sufficient for many portable biomedical, test, and measurement signals, and the 3 V/µs slew rate provides adequate response for moderate waveform edges. Battery rails and sensor outputs must remain within the amplifier's supported common-mode and supply ranges.
推薦
推薦產品摘要
工程參考資料,適用於 INA105KUG4 — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | INA105U | INA105K | INA105UA | AD8271BRZ | AD8210JRZ |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Analog Devices | Analog Devices |
| Package | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC |
| Amplifier Function | Unity-gain differential amplifier | Unity-gain differential amplifier | Unity-gain differential amplifier | Unity-gain differential amplifier | Differential amplifier | Differential amplifier |
| Circuit Count | 1 circuit | 1 circuit | 1 circuit | 1 circuit | 1 circuit | 1 circuit |
主要差異化特點
- Integrated fixed-gain precision network (對比AD8210JRZ)
- Confirmed 1 MHz signal bandwidth (對比AD8210JRZ)
- Monolithic resistor tracking (對比AD8271BRZ)
設計說明
Route the two differential inputs as a closely matched pair and minimize asymmetry in trace length, connector geometry, and input filtering. Any difference between the two paths can create differential-input impedance mismatch that reduces common-mode rejection. Place input and bypass capacitors near their associated pins, and use a low-impedance ground plane to prevent supply return currents from sharing the input-signal return path.
Check source impedance before relying on the specified 1 MHz -3 dB bandwidth. The manufacturer headline bandwidth applies under specified test conditions, including source and load conditions that must be read in the datasheet. If either sensor has substantial output impedance, include its attenuation and phase contribution in the complete signal-path response. Differential filtering should use matched components to avoid converting common-mode noise into differential error.
Do not treat unity gain as immunity to input common-mode limits. The input common-mode voltage must remain within the operating region established in the Texas Instruments INA105 datasheet, including limits that can vary with supply voltage. Likewise, verify output swing at the required load before using the 3 V/µs slew-rate specification for a large-amplitude signal. A numerically fast amplifier can still clip if its output range is insufficient.
Place the INA105KUG4 close to the source or bridge to minimize exposed sensitive traces and susceptibility to coupled noise. Decouple each supply connection locally and provide an adequate ground return without introducing long current loops through the analog section. Because the device uses a precision integrated resistor network, mechanical stress and board contamination are generally more important to long-term accuracy than adding additional discrete gain-setting resistors.
合規資訊
The INA105 is a precision analog amplifier rather than an automotive-qualified device, so AEC-Q100 is not applicable. No explicit compliance declarations were identified in the cited manufacturer or distributor results.