LM2904VQDRQ1 - Dual 30V 700kHz Op Amp | Texas Instruments
MPN: LM2904VQDRQ1 ✓ 啟用中LM2904VQDRQ1 概覽
An operational amplifier is an analog integrated circuit that uses high open-loop gain and negative feedback to amplify the difference between two input voltages. The LM2904 family belongs to the operational-amplifier hierarchy within analog and mixed-signal semiconductors. Its dual-channel architecture makes it useful for general-purpose signal conditioning, buffering, feedback amplification, voltage comparison, and instrumentation functions where a wide supply-voltage range and elevated-temperature capability are valuable.
The principal performance characteristics include two amplifier channels, a 700 kHz gain-bandwidth product, and a maximum total supply voltage of 30 V. The manufacturer identifies the LM2904VQDRQ1 as an automotive AEC-Q100-qualified dual operational amplifier in an 8-SOIC package. It also has a high-gain configuration suitable for closed-loop amplifier stages and comparator-like functions. These characteristics position it between precision low-noise amplifiers and high-speed wideband amplifiers: it provides more bandwidth than a basic general-purpose amplifier while retaining a simple, industry-standard package.
The LM2904V product family uses conventional internal compensation and is intended for general-purpose operation rather than rail-to-rail input or output designs. Its supply-voltage tolerance permits operation from automotive and industrial battery-derived rails, although each application must remain within the device's absolute maximum and recommended operating limits. Because both amplifiers share the same package, their power rails are common, while the signal inputs and outputs remain independent.
Typical automotive uses include low-frequency sensor conditioning, actuator signal interfaces, active filtering, and general control-system analog channels. The same device can support industrial instrumentation, audio and communications interfaces, and voltage-feedback amplifier stages. For dual-rail designs, the two channels can process related or unrelated signals, allowing a more compact implementation than two separate single-channel amplifiers.
Designers should verify input and output common-mode ranges, output swing, stability with the selected feedback network, and noise performance against their signal bandwidth. The SOIC outline also requires attention to exposed copper and thermal dissipation when operating continuously near the upper temperature limit. Bypass capacitors should be placed close to the supply pins, and sensitive input traces should remain short and away from switching nodes.
This product page combines the exact ordering information, operating limits, package details, automotive qualification, pin assignment, qualification alternatives, and application-oriented design guidance for LM2904VQDRQ1. It is intended to help engineers determine whether this dual, 30 V, 700 kHz operational amplifier fits a new design or can be introduced through a controlled board-level replacement process.
直接替換替代品,適用於 LM2904VQDRQ1 — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: LM2904VQDRQ1 (相同外形與佔位) — 差異在於 Gain-Bandwidth Product, Maximum Supply Voltage, Package, Number of Channels, Automotive Qualification.
LM2904VQDR
✅ 直接替換聯絡詢價
查看資料表 →LM2904QDRQ1
✅ 直接替換✗ 缺貨
$0.22 / 單位
查看資料表 →LM2904LVQDRQ1
✅ 直接替換聯絡詢價
查看資料表 →LM2904VQDRQ1 最大額定值與電氣特性
| Product Type | Dual general-purpose operational amplifier |
| Number of Channels | 2 channels |
| Maximum Total Supply Voltage | 30 V |
| Maximum Supply Voltage | 32 V |
| Gain-Bandwidth Product | 700 kHz |
| 工作溫度範圍 | -40°C to +125°C |
| 封裝 | 8-pin SOIC, 3.90 mm width |
| 安裝類型 | Surface mount |
| Automotive Qualification | AEC-Q100 qualified |
| 生命週期狀態 | Active |
LM2904VQDRQ1 腳位配置
| 腳位 1 | OUT A — Output of amplifier A |
| 腳位 2 | IN A- — Inverting input of amplifier A |
| 腳位 3 | IN A+ — Non-inverting input of amplifier A |
| 腳位 4 | V- — Negative supply connection |
| 腳位 5 | IN B+ — Non-inverting input of amplifier B |
| 腳位 6 | IN B- — Inverting input of amplifier B |
| 腳位 7 | OUT B — Output of amplifier B |
| 腳位 8 | V+ — Positive supply connection |
典型應用
LM2904VQDRQ1 適用於 6 應用s: Automotive Sensor Signal Conditioning, Industrial Instrumentation Amplification, Active Audio and Communication Filtering, Voltage Feedback Control Loops, Battery and Power-Supply Monitoring, Data Acquisition and Sensor Interfaces.
Automotive Sensor Signal Conditioning
The LM2904VQDRQ1 fits low-frequency automotive sensor conditioning because it combines two amplifier channels, a 700 kHz gain-bandwidth product, and operation across -40°C to 125°C in an AEC-Q100-qualified 8-pin SOIC package. Place one channel in a non-inverting or differential amplifier stage around a resistive sensor and use the second channel for an active filter, reference buffer, or output-conditioning stage. The dual layout can reduce the number of separate amplifier packages on a control board. Because this is a general-purpose rather than rail-to-rail amplifier, verify the sensor’s common-mode range and the required output swing across the automotive supply range. Input protection, ground-return routing, and filter stability should be evaluated before production release.
推薦
Industrial Instrumentation Amplification
The LM2904VQDRQ1 is suitable for general industrial instrumentation where two analog channels must be amplified within a 30 V maximum total supply environment. Its 700 kHz gain-bandwidth product supports low-to-moderate-bandwidth sensor and process-control signals, while the 8-pin SOIC package supports compact, surface-mounted control assemblies. A typical implementation uses one channel for a low-level sensor stage and the other for a buffer or active anti-alias filter. The integrated circuit is not rail-to-rail, so the common-mode and output ranges must be checked against the transducer interface. Place the power bypass capacitor near pin 8 and connect pin 4 to the ground reference through a low-impedance return path to minimize channel interaction.
推薦
Active Audio and Communication Filtering
The LM2904VQDRQ1 can implement first- and second-order active filters or signal-conditioning stages for communications and audio interfaces because each channel provides independent gain and filtering functions. The 700 kHz gain-bandwidth product is appropriate for low-frequency tasks such as microphone preamplification, anti-alias filtering, and line-level buffering when the closed-loop gain is chosen with adequate stability margin. Its 30 V maximum total supply rating also accommodates higher-amplitude analog stages within the specified operating limits. Avoid using the device as a rail-to-rail line driver because that is not an identified capability. Validate output swing, distortion, noise, and channel-to-channel behavior in the completed network, especially when the input or output approaches a supply rail.
推薦
Voltage Feedback Control Loops
The LM2904VQDRQ1 is appropriate for conventional voltage-feedback control and feedback-amplifier circuits requiring a gain-bandwidth product of 700 kHz. One channel can implement the forward error amplifier while the other provides feedback monitoring or a secondary compensation function. The 8-pin SOIC arrangement simplifies routing in multi-loop industrial or automotive electronics, and the -40°C to 125°C range supports harsh-temperature operation. Designers should select resistor and capacitor values that preserve phase margin across the intended gain, load, and supply range. Keep feedback traces short, isolate the output from sensitive input routing, and check the loop response rather than relying only on the device’s gain-bandwidth figure. The manufacturer datasheet should govern all recommended operating and stability conditions.
推薦
Battery and Power-Supply Monitoring
The LM2904VQDRQ1 can supervise or amplify voltage-monitoring signals in industrial power systems because it accepts a wide supply-voltage environment and operates from -40°C to 125°C. One channel may amplify a divided battery or bus-voltage signal, while the second channel conditions a current-sense or temperature reference for comparison with a threshold. The 700 kHz bandwidth is more than sufficient for many slow monitoring paths, although the final filter should reject switching noise. Place the amplifier near the sensed divider to reduce pickup, use a quiet ground reference, and maintain separation from high-current switch nodes. Verify that the monitored signal stays inside the amplifier’s input common-mode range and that the output remains within the required logic or ADC input range.
推薦
Data Acquisition and Sensor Interfaces
The LM2904VQDRQ1 supports compact data-acquisition front ends that require two conditioned channels and a moderate closed-loop bandwidth. Typical uses include transducer amplification, differential-to-single-ended conversion, anti-alias filtering, and buffering of higher-impedance sources. The 700 kHz gain-bandwidth product allows useful bandwidth at lower closed-loop gains, while the 8-pin SOIC package keeps the implementation compact for multichannel analog boards. Because input bias current and offset can affect high-impedance sources, compare the detailed electrical characteristics with the sensor impedance and required accuracy. Use short, guarded input traces and a solid ground plane, and check the ADC acquisition window after adding the output filter to prevent settling errors from degrading conversion accuracy.
推薦
推薦產品摘要
工程參考資料,適用於 LM2904VQDRQ1 — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | LM2904VQDR | LM2904QDRQ1 | LM2904LVQDRQ1 |
|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 8-SOIC | 8-SOIC - same | 8-SOIC - same | 8-SOIC - same |
| Number of Channels | 2 | 2 | 2 | 2 |
| Gain-Bandwidth Product | 700 kHz | 700 kHz | 700 kHz | 700 kHz |
| Slew Rate | 0.3 V/us | 0.3 V/us | 0.3 V/us | 0.3 V/us |
| Maximum Input Offset Voltage at 25°C | 7 mV | 7 mV | 2 mV | 3 mV ultra-low offset |
| Primary Functional Difference | Standard V offset grade | Standard V offset grade without Q1 suffix | Lower 2 mV maximum offset grade | Ultra-low 3 mV offset grade |
主要差異化特點
- Provides the standard V offset grade with automotive Q1 qualification (對比LM2904VQDR)
- Lower documented offset limit than the non-V standard grade (對比LM2904QDRQ1)
- Standard V-grade electrical positioning rather than ultra-low-offset positioning (對比LM2904LVQDRQ1)
設計說明
Connect the supply bypass capacitor directly between pins 8 and 4, with the ground end returned to a low-impedance ground plane. Keep the 8-pin SOIC footprint and decoupling layout identical when evaluating LM2904QDRQ1 or LM2904LVQDRQ1 as replacements. Route the two channels independently to avoid shared high-impedance feedback traces, and maintain separation from power-switching nodes and motor-drive return currents.
Treat pins 2, 3, 5, and 6 as sensitive high-impedance inputs. Use short traces, avoid routing beneath noisy power stages, and keep the feedback components close to the relevant channel. When the source impedance is high, compare the complete input-bias-current error budget from the manufacturer datasheet with the sensor impedance; the 700 kHz gain-bandwidth value alone does not establish DC accuracy.
Do not assume rail-to-rail input or output behavior, and verify the common-mode input range and output swing against the actual supply arrangement. The -40°C to 125°C operating range does not permit every operating parameter to remain constant over that interval. Use the manufacturer recommended operating conditions and absolute maximum ratings, and confirm output stability with the selected gain, load capacitance, and feedback network.
The 8-pin SOIC package is compact, and continuous automotive or industrial operation near 125°C requires adequate board copper and attention to nearby heat sources. Estimate dissipation from the actual supply voltage, output voltage, load current, and quiescent current, then compare the resulting junction temperature with the device limit. Keep heat-generating regulators and power stages apart from precision analog channels to reduce temperature gradients and offset drift.
合規資訊
The LM2904VQDRQ1 ordering information identifies AEC-Q100 automotive qualification. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status were not explicitly established for this exact ordering configuration.