ISL8323IB-T - Dual 60Ω SPST Analog Switch | Renesas
MPN: ISL8323IB-T ✓ 啟用中ISL8323IB-T 概覽
An analog switch is an integrated interface IC that routes signals between terminals with controlled impedance. A single-pole, single-throw, or SPST, switch has one conducting path when enabled and an open circuit when disabled. The ISL8323 uses two such paths in one package, making it useful when a design needs to isolate, disconnect, or select two analog signals without using mechanical relays.
The primary electrical characteristics include two switch circuits, 60 ohm on-resistance, and normally open contacts. The manufacturer datasheet information identifies maximum charge injection of 5 pC, off-state channel capacitance of 9 pF, maximum off-state leakage current of 100 pA, and crosstalk of -85 dB at 1 MHz. These parameters determine how much switching transients and signal coupling can affect sensitive downstream circuits.
The ISL8323 family supports single-supply operation, with the documented supply range extending to 12 V. Its low-voltage architecture is appropriate for battery-powered instruments, portable measurement equipment, automated test systems, and low-voltage control systems. Two separate switches can route independent control or sensor signals while sharing a common supply and ground reference.
Use the ISL8323IB-T when normally open behavior is required. The related ISL8324 provides normally closed switches, while the ISL8325 combines one normally open and one normally closed switch for SPDT-style routing. Because contact state changes the logic behavior, these family members are not automatic drop-in substitutes for an existing normally open design.
Layout should minimize trace length around the switched nodes, maintain a continuous ground reference, and keep sensitive signal paths away from noisy supply and control routes. Confirm the control levels, input voltage range, break-before-make behavior, and application leakage budget against the manufacturer datasheet before production release.
This product page combines the switch configuration, electrical limits, package information, family distinctions, and application guidance needed to evaluate the ISL8323IB-T and identify a valid replacement without relying on packaging suffix changes alone.
直接替換替代品,適用於 ISL8323IB-T — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: ISL8323IB-T (相同外形與佔位) — 差異在於 Package, Switch Configuration.
ISL8323IB
✅ 直接替換聯絡詢價
查看資料表 →ISL8323IBZ-T
✅ 直接替換📋 參考替代品(不在目錄中)
ISL8323IB-T 最大額定值與電氣特性
| Number of Switch Circuits | 2 circuits |
| Switch Configuration | 2 independent normally open SPST switches |
| On-Resistance | 60 ohm |
| Maximum Charge Injection | 5 pC |
| Off-State Channel Capacitance | 9 pF |
| Maximum Off-State Leakage Current | 100 pA |
| Crosstalk | -85 dB at 1 MHz |
| Maximum Supply Voltage | 12 V |
| 工作溫度 | -40°C to +85°C |
| 封裝 | 8-SOIC, 3.90 mm width |
| 安裝類型 | Surface mount |
| Supply Type | Single supply |
| Switch Type | SPST, 1:1 |
| Contact State | Normally open |
| Product Family | ISL8323 low-voltage analog switch series |
ISL8323IB-T 8-soic, 3.90 mm width 腳位配置指南
ISL8323IB-T(8-soic, 3.90 mm width 封裝)的腳位配置。 腳位編號、功能與連接圖定義於製造商資料手冊中。請參閱該手冊以取得確切的封裝尺寸與焊接指引。
無詳細腳位定義資料: ISL8323IB-T.
請參閱 資料表 以查看完整腳位配置。
典型應用
ISL8323IB-T 適用於 6 應用s: Portable Measurement Instrumentation, Battery-Powered Sensor Interfaces, Automated Test Equipment Signal Routing, Low-Voltage Control Signal Multiplexing, Precision Analog Signal Isolation, Industrial Data Acquisition.
Portable Measurement Instrumentation
The ISL8323IB-T fits portable measurement equipment that must route or disconnect two low-level analog signals while operating from a single supply. Its two normally open SPST paths provide independent isolation, and the 60 ohm on-resistance keeps insertion loss manageable for many sensor-conditioning stages. The 5 pC maximum charge injection is especially relevant when the switch drives a high-impedance amplifier input. Place the device close to the protected sensor node, use short traces, and verify that switching transients remain below the measurement uncertainty.
推薦
Battery-Powered Sensor Interfaces
The ISL8323IB-T can isolate two sensor signals in battery-operated equipment where a single low-voltage supply is required. Its normally open contacts remain disconnected until enabled, helping prevent unwanted loading or signal coupling between channels. The maximum off-state leakage of 100 pA is useful for high-source-impedance sensing, while the 9 pF off-state capacitance contributes to input loading. Engineers should account for both values when setting source impedance, settling time, and the available power budget.
推薦
Automated Test Equipment Signal Routing
The ISL8323IB-T supports two independently switched analog paths in automated test systems where a fixture must connect, isolate, or route DUT signals. A 60 ohm on-resistance is practical for many low-frequency and moderate-impedance test paths. For high-impedance nodes, however, the 5 pC charge-injection limit requires careful timing around switch commands. The 8-SOIC package also allows routing away from a connector-heavy edge region while preserving a conventional surface-mount assembly process.
推薦
Low-Voltage Control Signal Multiplexing
The two normally open switches in the ISL8323IB-T can select or disconnect separate control signals in a low-voltage embedded control subsystem. With a documented operating range extending to 12 V, the device suits systems using a single supply rather than split positive and negative rails. Its -85 dB crosstalk at 1 MHz indicates strong isolation between channels at that test frequency. Verify actual signal bandwidth and logic thresholds because those application conditions are not fully characterized by the crosstalk point alone.
推薦
Precision Analog Signal Isolation
The ISL8323IB-T is appropriate for isolating one analog signal while routing another in precision front ends. Its normally open behavior provides a defined disconnected state, and the 100 pA maximum off-state leakage limits leakage from high-impedance sources. The 5 pC charge injection must still be included in the settling-time analysis after each control transition. Use a nearby reference return path and avoid long, parallel switched-node traces to minimize capacitive pickup and maintain isolation performance.
推薦
Industrial Data Acquisition
The ISL8323IB-T can route two inputs in compact industrial data-acquisition equipment where the analog front end must support channel selection or galvanic-style functional isolation within a single-supply architecture. Its -40°C to +85°C operating-temperature range supports industrial environments when the complete assembly meets its own thermal requirements. The 60 ohm on-resistance should be included in the input-buffer design, and the 9 pF off-state capacitance should be checked against required settling time and bandwidth.
推薦
推薦產品摘要
工程參考資料,適用於 ISL8323IB-T — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | ISL8323IB | ISL8323IBZ-T |
|---|---|---|---|
| Brand | Renesas Electronics | Renesas Electronics | Renesas Electronics |
| Package | 8-SOIC | 8-SOIC | 8-SOIC |
| Switch Circuits | 2 circuits | 2 circuits | 2 circuits |
| Switch Configuration | 1:1 SPST, normally open | 1:1 SPST, normally open | 1:1 SPST, normally open |
| On-Resistance | 60 ohm | 60 ohm | 60 ohm |
| Maximum Charge Injection | 5 pC | 5 pC | 5 pC |
| Off-State Channel Capacitance | 9 pF | 9 pF | 9 pF |
| Maximum Off-State Leakage Current | 100 pA | 100 pA | 100 pA |
| Crosstalk | -85 dB at 1 MHz | -85 dB at 1 MHz | -85 dB at 1 MHz |
| Operating Temperature | -40°C to +85°C | -40°C to +85°C | -40°C to +85°C |
主要差異化特點
- Two independent normally open analog paths in one package (對比ISL8323IB)
- Low charge injection for precision signal isolation (對比ISL8323IBZ-T)
- Documented channel isolation (對比ISL8323IB)
設計說明
Treat the switched nodes as sensitive analog signals. The documented 9 pF off-state capacitance can create settling transients, while 5 pC maximum charge injection can disturb a high-impedance receiver when a control input changes. Keep input and output impedance values realistic, allow adequate settling time after switching, and verify the complete source-switch-load network with an oscilloscope before fixing acquisition timing.
Place the ISL8323IB-T close to the two switched signal paths and use the manufacturer 8-SOIC footprint. Keep input and output traces short and avoid routing them beneath noisy digital or switching-supply traces. Connect the device ground to the quiet analog ground reference with a low-impedance path, and keep the enable or control traces away from high-impedance switched nodes to reduce coupled transitions.
Do not treat the ISL8324 or ISL8325 as automatic replacements: their normally closed or mixed contact states change the circuit logic. Also verify that the on-resistance of 60 ohm is acceptable for the source and load, and that the 100 pA off-state leakage is below the measurement error budget. Confirm the exact ordering suffix, grade, package marking, and control polarity before production procurement.
合規資訊
The target MPN is a general-purpose analog switch rather than an automotive-qualified device. Specific RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations are not stated for this exact orderable MPN.