ISL8323IB-T - Dual 60Ω SPST Analog Switch | Renesas
料号: ISL8323IB-T ✓ 量产中ISL8323IB-T 概述
An analog switch is an integrated interface IC that routes signals between terminals with controlled impedance. A single-pole, single-throw, or SPST, switch has one conducting path when enabled and an open circuit when disabled. The ISL8323 uses two such paths in one package, making it useful when a design needs to isolate, disconnect, or select two analog signals without using mechanical relays.
The primary electrical characteristics include two switch circuits, 60 ohm on-resistance, and normally open contacts. The manufacturer datasheet information identifies maximum charge injection of 5 pC, off-state channel capacitance of 9 pF, maximum off-state leakage current of 100 pA, and crosstalk of -85 dB at 1 MHz. These parameters determine how much switching transients and signal coupling can affect sensitive downstream circuits.
The ISL8323 family supports single-supply operation, with the documented supply range extending to 12 V. Its low-voltage architecture is appropriate for battery-powered instruments, portable measurement equipment, automated test systems, and low-voltage control systems. Two separate switches can route independent control or sensor signals while sharing a common supply and ground reference.
Use the ISL8323IB-T when normally open behavior is required. The related ISL8324 provides normally closed switches, while the ISL8325 combines one normally open and one normally closed switch for SPDT-style routing. Because contact state changes the logic behavior, these family members are not automatic drop-in substitutes for an existing normally open design.
Layout should minimize trace length around the switched nodes, maintain a continuous ground reference, and keep sensitive signal paths away from noisy supply and control routes. Confirm the control levels, input voltage range, break-before-make behavior, and application leakage budget against the manufacturer datasheet before production release.
This product page combines the switch configuration, electrical limits, package information, family distinctions, and application guidance needed to evaluate the ISL8323IB-T and identify a valid replacement without relying on packaging suffix changes alone.
直接替换替代料: ISL8323IB-T ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: ISL8323IB-T (相同外形与封装尺寸) ——差异在于 Package, Switch Configuration.
ISL8323IB
✅ 直接替换联系询价
查看数据手册 →ISL8323IBZ-T
✅ 直接替换📋 参考替代料(不在目录中)
ISL8323IB-T 最大额定值与电气特性
| Number of Switch Circuits | 2 circuits |
| Switch Configuration | 2 independent normally open SPST switches |
| On-Resistance | 60 ohm |
| Maximum Charge Injection | 5 pC |
| Off-State Channel Capacitance | 9 pF |
| Maximum Off-State Leakage Current | 100 pA |
| Crosstalk | -85 dB at 1 MHz |
| Maximum Supply Voltage | 12 V |
| 工作温度 | -40°C to +85°C |
| 封装 | 8-SOIC, 3.90 mm width |
| 安装类型 | Surface mount |
| Supply Type | Single supply |
| Switch Type | SPST, 1:1 |
| Contact State | Normally open |
| Product Family | ISL8323 low-voltage analog switch series |
ISL8323IB-T 8-soic, 3.90 mm width 引脚配置指南
ISL8323IB-T(8-soic, 3.90 mm width 封装)的引脚配置。 引脚编号、功能和连接图在制造商数据手册中定义。请参阅该手册以了解确切的封装尺寸和焊接指南。
暂无详细引脚数据: ISL8323IB-T.
请参阅 数据手册 以查看完整引脚配置。
典型应用
ISL8323IB-T 适用于 6 应用s: Portable Measurement Instrumentation, Battery-Powered Sensor Interfaces, Automated Test Equipment Signal Routing, Low-Voltage Control Signal Multiplexing, Precision Analog Signal Isolation, Industrial Data Acquisition.
Portable Measurement Instrumentation
The ISL8323IB-T fits portable measurement equipment that must route or disconnect two low-level analog signals while operating from a single supply. Its two normally open SPST paths provide independent isolation, and the 60 ohm on-resistance keeps insertion loss manageable for many sensor-conditioning stages. The 5 pC maximum charge injection is especially relevant when the switch drives a high-impedance amplifier input. Place the device close to the protected sensor node, use short traces, and verify that switching transients remain below the measurement uncertainty.
推荐
Battery-Powered Sensor Interfaces
The ISL8323IB-T can isolate two sensor signals in battery-operated equipment where a single low-voltage supply is required. Its normally open contacts remain disconnected until enabled, helping prevent unwanted loading or signal coupling between channels. The maximum off-state leakage of 100 pA is useful for high-source-impedance sensing, while the 9 pF off-state capacitance contributes to input loading. Engineers should account for both values when setting source impedance, settling time, and the available power budget.
推荐
Automated Test Equipment Signal Routing
The ISL8323IB-T supports two independently switched analog paths in automated test systems where a fixture must connect, isolate, or route DUT signals. A 60 ohm on-resistance is practical for many low-frequency and moderate-impedance test paths. For high-impedance nodes, however, the 5 pC charge-injection limit requires careful timing around switch commands. The 8-SOIC package also allows routing away from a connector-heavy edge region while preserving a conventional surface-mount assembly process.
推荐
Low-Voltage Control Signal Multiplexing
The two normally open switches in the ISL8323IB-T can select or disconnect separate control signals in a low-voltage embedded control subsystem. With a documented operating range extending to 12 V, the device suits systems using a single supply rather than split positive and negative rails. Its -85 dB crosstalk at 1 MHz indicates strong isolation between channels at that test frequency. Verify actual signal bandwidth and logic thresholds because those application conditions are not fully characterized by the crosstalk point alone.
推荐
Precision Analog Signal Isolation
The ISL8323IB-T is appropriate for isolating one analog signal while routing another in precision front ends. Its normally open behavior provides a defined disconnected state, and the 100 pA maximum off-state leakage limits leakage from high-impedance sources. The 5 pC charge injection must still be included in the settling-time analysis after each control transition. Use a nearby reference return path and avoid long, parallel switched-node traces to minimize capacitive pickup and maintain isolation performance.
推荐
Industrial Data Acquisition
The ISL8323IB-T can route two inputs in compact industrial data-acquisition equipment where the analog front end must support channel selection or galvanic-style functional isolation within a single-supply architecture. Its -40°C to +85°C operating-temperature range supports industrial environments when the complete assembly meets its own thermal requirements. The 60 ohm on-resistance should be included in the input-buffer design, and the 9 pF off-state capacitance should be checked against required settling time and bandwidth.
推荐
推荐产品汇总
工程参考数据: ISL8323IB-T ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | ISL8323IB | ISL8323IBZ-T |
|---|---|---|---|
| Brand | Renesas Electronics | Renesas Electronics | Renesas Electronics |
| Package | 8-SOIC | 8-SOIC | 8-SOIC |
| Switch Circuits | 2 circuits | 2 circuits | 2 circuits |
| Switch Configuration | 1:1 SPST, normally open | 1:1 SPST, normally open | 1:1 SPST, normally open |
| On-Resistance | 60 ohm | 60 ohm | 60 ohm |
| Maximum Charge Injection | 5 pC | 5 pC | 5 pC |
| Off-State Channel Capacitance | 9 pF | 9 pF | 9 pF |
| Maximum Off-State Leakage Current | 100 pA | 100 pA | 100 pA |
| Crosstalk | -85 dB at 1 MHz | -85 dB at 1 MHz | -85 dB at 1 MHz |
| Operating Temperature | -40°C to +85°C | -40°C to +85°C | -40°C to +85°C |
关键差异点
- Two independent normally open analog paths in one package (对比 ISL8323IB)
- Low charge injection for precision signal isolation (对比 ISL8323IBZ-T)
- Documented channel isolation (对比 ISL8323IB)
设计说明
Treat the switched nodes as sensitive analog signals. The documented 9 pF off-state capacitance can create settling transients, while 5 pC maximum charge injection can disturb a high-impedance receiver when a control input changes. Keep input and output impedance values realistic, allow adequate settling time after switching, and verify the complete source-switch-load network with an oscilloscope before fixing acquisition timing.
Place the ISL8323IB-T close to the two switched signal paths and use the manufacturer 8-SOIC footprint. Keep input and output traces short and avoid routing them beneath noisy digital or switching-supply traces. Connect the device ground to the quiet analog ground reference with a low-impedance path, and keep the enable or control traces away from high-impedance switched nodes to reduce coupled transitions.
Do not treat the ISL8324 or ISL8325 as automatic replacements: their normally closed or mixed contact states change the circuit logic. Also verify that the on-resistance of 60 ohm is acceptable for the source and load, and that the 100 pA off-state leakage is below the measurement error budget. Confirm the exact ordering suffix, grade, package marking, and control polarity before production procurement.
合规信息
The target MPN is a general-purpose analog switch rather than an automotive-qualified device. Specific RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations are not stated for this exact orderable MPN.