LC4064C-75T44C - 64-Macrocell 7.5ns CPLD | Lattice
MPN: LC4064C-75T44C ✗ 停產LC4064C-75T44C 概覽
A complex programmable logic device, or CPLD, belongs to the programmable-logic hierarchy that includes FPGAs. Unlike a software-programmed microcontroller, a CPLD stores a defined Boolean logic configuration in nonvolatile configuration memory. The LC4064C combines multiple logic blocks with a programmable interconnect, allowing fixed digital functions such as interface control, address decoding, state sequencing, and glue logic to operate predictably after configuration.
The 64-macrocell architecture provides a practical balance between logic capacity and routing resources for compact control systems. Its 7.5 ns speed grade is suitable for clocked control logic, data acquisition, peripheral interfacing, and general-purpose digital subsystems. In-system programmability allows a board to be configured or updated through the device's programming interface, while the 44-pin TQFP package supports conventional surface-mount assembly.
The device is associated with the Lattice ispMACH 4000C family and supports multiple supply-voltage configurations identified for the LC4064C family. Unlike a microcontroller with a processor core and executable software, this CPLD uses configurable logic blocks and fixed interconnect resources. This architecture can provide deterministic hardware behavior after configuration and can consolidate several discrete gates and counters into one programmable component.
Typical applications include industrial control interfaces, test and measurement equipment, communications link control, embedded data-acquisition systems, power-system sequencing, and compact peripheral adapters. A design can implement parallel data capture, pulse-width generation, protocol framing, and status logic in one device when the required architecture fits the available macrocells and I/O resources.
Design planning should begin with a complete pin assignment and timing review using the Lattice Semiconductor datasheet and the selected design toolchain. The PCB should preserve the device's required programming, configuration, clock, ground, and supply connections, while decoupling and layout should follow the package-specific recommendations. Programming files, pin constraints, timing constraints, and unused-pin treatment must be reviewed before fabrication.
This page organizes the verified device identity, package, programming characteristics, speed grade, and practical design considerations while identifying family-based drop-in alternatives. It also distinguishes the LC4064C from the LC4064V, highlights speed-grade and temperature-suffix trade-offs, and provides comparison points that help engineers determine PCB, timing, and qualification impacts before approving a substitution.
直接替換替代品,適用於 LC4064C-75T44C — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: LC4064C-75T44C (相同外形與佔位) — 差異在於 Architecture, Speed Grade, Device Type, Configuration Memory, Product Family.
LC4064C-75T44I
✅ 直接替換聯絡詢價
查看資料表 →LC4064C-75TN44C
✅ 直接替換📋 參考替代品(不在目錄中)
LC4064C-25T44C
✅ 直接替換聯絡詢價
查看資料表 →LC4064C-10T44C
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
LC4064V-75T44C
✅ 直接替換聯絡詢價
查看資料表 →LC4064C-75T44C 最大額定值與電氣特性
| Device Type | Complex Programmable Logic Device (CPLD) |
| Product Family | ispMACH 4000C |
| Macrocell Count | 64 macrocells |
| Logic Block Count | 4 logic blocks |
| Maximum Propagation Delay | 7.5 ns |
| 封裝 | 44-pin TQFP |
| 安裝類型 | Surface mount |
| Programmability | In-system programmable |
| Supported Supply Configurations | 3.3 V, 2.5 V, and 1.8 V |
| Internal Supply Voltage Range | 1.65 V to 1.95 V |
| Speed Grade | 75 speed grade, 7.5 ns maximum propagation delay |
| Device Technology | SuperFAST high-density PLD |
| Configuration Memory | Nonvolatile programmable logic configuration |
LC4064C-75T44C 44-pin tqfp 腳位配置指南
LC4064C-75T44C(44-pin tqfp 封裝)的腳位配置。 此數位 IC 包含 GPIO、通訊介面(UART、SPI、I2C)與電源腳位。替代腳位功能與配置選項請參閱製造商資料表。對嵌入式系統設計與 PCB 佈局至關重要。
無詳細腳位定義資料: LC4064C-75T44C.
請參閱 資料表 以查看完整腳位配置。
典型應用
LC4064C-75T44C 適用於 6 應用s: Industrial Control Interface Logic, Data Acquisition and Signal Conditioning, Communications Link Control, Test and Measurement Equipment, Power Sequencing and Monitoring, Embedded Peripheral Adapter.
Industrial Control Interface Logic
The LC4064C-75T44C is suitable for consolidating fixed industrial control functions into one programmable device. Its 64 macrocells across four logic blocks can implement state machines, interlocks, command decoding, alarm handling, and discrete I/O buffering without a microcontroller software loop. The 7.5 ns maximum propagation delay supports higher-clock control logic when external setup and hold requirements are met. In-system programming permits board-level configuration during production or field update. For industrial deployment, choose the suffix whose specified temperature range matches the enclosure and verify supply tolerances, input thresholds, and output timing against the Lattice Semiconductor datasheet.
推薦
Data Acquisition and Signal Conditioning
The LC4064C can coordinate parallel data acquisition in a compact instrument by generating sample-control signals, multiplexing strobes, counting events, and transferring captured data to a host interface. Four logic blocks and 64 macrocells provide meaningful capacity for finite-state control logic while its 7.5 ns grade can support tightly timed digital paths. The 44-pin TQFP also offers a manageable surface-mount footprint for acquisition boards. Designers should allocate pins for the chosen bus width, verify input timing against the data source, and use the manufacturer pin-description and timing tables to prevent hold-time violations.
推薦
Communications Link Control
LC4064C-75T44C implementations can place framing, byte alignment, timeout detection, and transmitter-enable logic beside a communications transceiver. The device's programmable architecture permits protocol-specific constants to be implemented in hardware while its 64 macrocells support moderately complex control sequences. With a maximum propagation delay of 7.5 ns, the CPLD can support deterministic digital coordination between parallel transceiver logic and external controllers. The system designer must confirm that the selected I/O standard, voltage configuration, clocking method, and timing budget match the transceiver interface before schematic capture.
推薦
Test and Measurement Equipment
In test and measurement equipment, the LC4064C-75T44C can consolidate sequencing, trigger routing, status decoding, and instrument-bus control into a single programmable logic device. Its nonvolatile configuration supports repeatable operation after power-up, and in-system programming simplifies fixture updates when control sequences change. The four-block, 64-macrocell structure is suitable for coordinating measurement sequencing and peripheral registers without loading a general-purpose processor with every low-level transition. Designers should reserve pins for calibration, trigger, and service interfaces and validate worst-case timing over the required operating temperature.
推薦
Power Sequencing and Monitoring
The LC4064C-75T44C can implement a deterministic power-sequence controller that monitors enable inputs, inserts delays between rail transitions, records fault conditions, and issues control signals to regulators or load switches. Its in-system programmability allows sequencing rules to be adapted without changing fixed hardware, while the 7.5 ns grade supports fast decisions around clocked supervisory logic. The 44-pin TQFP provides access to multiple discrete and latch inputs in a compact package. For safety-related or high-availability systems, review watchdog behavior, fail-safe pin states, and single-fault considerations rather than relying on CPLD timing alone.
推薦
Embedded Peripheral Adapter
A compact adapter can use the LC4064C-75T44C to translate between legacy parallel ports, addressable peripherals, and modern serial controllers. Its 64 macrocells can hold address decoding, latch logic, interrupt masking, and data-width conversion, eliminating several discrete logic packages. The 7.5 ns speed class supports demanding clocked interfaces, while the 44-pin TQFP keeps the assembly manageable for embedded controller boards. Designers must verify every signal's voltage level, direction, termination requirement, and timing relationship in the datasheet and then constrain unused pins explicitly in the programming project.
推薦
推薦產品摘要
工程參考資料,適用於 LC4064C-75T44C — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | LC4064C-75T44I | LC4064C-75TN44C | LC4064C-25T44C | LC4064C-10T44C | LC4064V-75T44C |
|---|---|---|---|---|---|---|
| Brand | Lattice Semiconductor Corporation | Lattice Semiconductor Corporation | Lattice Semiconductor Corporation | Lattice Semiconductor Corporation | Lattice Semiconductor Corporation | Lattice Semiconductor Corporation |
| Package | TQFP-44 | TQFP-44 - same | TQFP-44 - same | TQFP-44 - same | TQFP-44 - same | TQFP-44 - same |
| Device Type | CPLD | CPLD | CPLD | CPLD | CPLD | CPLD |
| Maximum Propagation Delay | 7.5 ns | 7.5 ns | 7.5 ns | 25 ns | 10 ns | 7.5 ns |
| Speed Grade | 75 speed grade | 75 speed grade | 75 speed grade | 25 speed grade | 10 speed grade | 75 speed grade |
| In-System Programming | Supported | Supported | Supported | Supported | Supported | Supported |
主要差異化特點
- Balances logic capacity with a compact 44-pin package (對比LC4064V-75T44C)
- Same timing grade as the closest LC4064C industrial suffix (對比LC4064C-75T44I)
- Lower propagation delay than slower speed-grade alternatives (對比LC4064C-25T44C)
- Faster timing than the 10 ns family option (對比LC4064C-10T44C)
設計說明
Do not approve a suffix-only replacement without checking the complete order code. For LC4064C-75T44C, the speed grade, package, temperature suffix, and lead or ordering attributes can change across otherwise similar MPNs. Compare the datasheet ordering table, pin table, voltage limits, timing limits, and temperature grade. After substitution, rerun the complete CPLD design compile and timing analysis because changes in grade or family can alter timing constraints even when the physical package remains the same.
Route programming signals, configuration control, clock inputs, supply pins, and ground pins according to the Lattice Semiconductor package and reference-design guidance. Place input and output decoupling capacitors close to their associated supply and ground pins, provide adequate return paths for switching currents, and keep sensitive timing or analog-adjacent signals away from noisy programming or power-conversion nodes. Treat every TQFP pad and exposed thermal requirement shown in the package drawing as a physical design constraint.
Establish input and output timing constraints from the actual external devices rather than relying only on the CPLD's 7.5 ns propagation-delay value. Account for clock skew, setup time, hold time, output loading, and board-level delay. For a replacement using the 10 ns or 25 ns grade, recalculate the complete path and preserve adequate margin. For new PCB designs, assign unused pins in the design project and configure them according to the manufacturer's recommendations.
Design the supply network for the exact voltage mode and current required by the selected operating configuration. Decoupling requirements and current consumption can vary with device family, speed grade, and I/O activity, so use the relevant datasheet tables rather than transferring a generic CPLD power layout. Verify power-up ordering if multiple rails control the design, and confirm that the CPLD's programming interface remains valid throughout the system's reset and initialization sequence.
合規資訊
The available product pages do not provide a definitive extract for the target's RoHS, REACH, lead-free, halogen-free, or conflict-minerals status. AEC-Q100 is not applicable because this is a general-purpose CPLD rather than an automotive-qualified device.