LM2903PSRG4 - Dual Differential Comparator | Texas Instruments
MPN: LM2903PSRG4 ✓ 啟用中LM2903PSRG4 概覽
A differential comparator is a semiconductor amplifier that compares two input voltages and changes its output state when the difference between them crosses a defined threshold. The LM2903 family belongs to the broader hierarchy of analog comparator ICs, analog signal-conditioning ICs, and semiconductor devices. Its two channels can be used independently, allowing one package to monitor two thresholds or control two independent signals.
The principal operating characteristics include a wide supply-voltage range, low supply-current drain independent of supply voltage, and a low input bias current of 25 nA. The open-collector output configuration allows each output to pull a logic signal low while an external pull-up resistor establishes the high state. This makes the device useful in interfaces requiring wired-AND behavior, relay-driver circuits, and systems that need a defined output voltage domain.
The LM2903PSRG4 operates from -40°C to +125°C, supporting industrial temperature environments. Its two independent comparator sections can evaluate separate signal pairs without sharing internal signal paths. Because the outputs are open collector, the maximum output voltage is determined mainly by the pull-up network and external supply rather than by a fixed internal high-level voltage. The 8-pin SOIC footprint supports compact surface-mount layouts in industrial control, instrumentation, power-supply monitoring, and interface circuits.
Typical uses include detecting overvoltage or undervoltage conditions, converting analog sensor thresholds into logic events, monitoring battery or power rails, and driving optocouplers or relay coils through suitable driver stages. The LM2903PSRG4 is particularly appropriate when the monitored signals remain within the comparator's input and supply limits and when an open-collector interface is acceptable.
When designing the circuit, choose the pull-up resistor to balance sink-current capacity, rise time, and power dissipation. Confirm the output current, input common-mode range, input offset voltage, response time, and absolute maximum ratings against the manufacturer datasheet before applying the device to a new voltage range. Account for switching transients and provide stable ground-return paths to prevent comparator chatter.
This product page organizes the LM2903PSRG4 specifications, package information, drop-in family alternatives, application guidance, and engineering design notes. It also provides a structured comparison for selecting a suitable comparator while preserving the same SOIC-8 footprint and pin arrangement.
直接替換替代品,適用於 LM2903PSRG4 — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: LM2903PSRG4 (相同外形與佔位) — 差異在於 Package, Operating Temperature Range, Output Type, Number of Channels, Maximum Supply Voltage.
LM2903DR
✅ 直接替換 ⚠️ 規格未經驗證聯絡詢價
查看資料表 →LM2903DBZR
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
LM2903MX/NOPB
✅ 直接替換聯絡詢價
查看資料表 →LM2903QDRG4
✅ 直接替換聯絡詢價
查看資料表 →LM2903DRG4
✅ 直接替換 ⚠️ 規格未經驗證聯絡詢價
查看資料表 →LM2903PSRG4 最大額定值與電氣特性
| Comparator Type | Dual differential comparator |
| Number of Channels | 2 channels |
| 輸出類型 | Open collector |
| Maximum Supply Voltage | 36 V |
| Dual-Supply Voltage Span | 2 V to 36 V |
| 供應電流 | 0.4 mA typical per comparator |
| Input Bias Current | 25 nA |
| 工作溫度 | -40°C to +125°C |
| 封裝 | 8-pin SOIC, 5.30 mm width |
| 腳位數 | 8 pins |
| 安裝類型 | Surface mount |
| Supply Configuration | Single supply or dual supplies |
| RoHS 狀態 | Compliant |
| Logic Output | Open collector, O-COL |
| 供應電壓 | 5 V |
LM2903PSRG4 8-pin soic, 5.30 mm width 腳位配置指南
LM2903PSRG4(8-pin soic, 5.30 mm width 封裝)的腳位配置。 此類比元件具有輸入、輸出與電源腳位。偏移歸零、補償與致能腳位配置請參閱製造商資料表。適用於訊號調理與放大器電路。
無詳細腳位定義資料: LM2903PSRG4.
請參閱 資料表 以查看完整腳位配置。
典型應用
LM2903PSRG4 適用於 6 應用s: Power-Supply Overvoltage Detection, Battery Voltage Monitoring, Sensor Threshold Conditioning, Industrial Control Interlocks, Relay and Optocoupler Interface, Automotive Electrical Qualification.
Power-Supply Overvoltage Detection
The LM2903PSRG4 is appropriate for monitoring a DC supply rail with two independent differential channels. Its 36 V maximum supply rating supports applications above the usual 5 V logic level, while the open-collector outputs can pull down an alert or shutdown input through an external pull-up resistor. The two channels can compare a protected rail against an upper threshold and a separate rail against a lower threshold. Before implementation, confirm that every monitored voltage remains within the comparator's input common-mode range and that the pull-up node does not exceed the allowable output voltage. The 0.4 mA typical current per comparator also helps limit the continuous supply burden of always-on protection logic.
推薦
Battery Voltage Monitoring
The LM2903PSRG4 can implement threshold-based battery monitoring by comparing a scaled battery voltage against a reference. Two independent comparator sections provide flexibility for monitoring charge and discharge limits, although the comparator outputs are open collector and therefore require pull-up resistors. The 25 nA input bias current is useful when working with high-impedance divider networks because it minimizes loading of the sensed voltage. The circuit must remain inside the device's input common-mode limits even when the battery voltage is low or the divider ratio changes. Use a resistor divider with appropriately scaled tolerance and verify stability across temperature before treating the output as a dependable battery state indicator.
推薦
Sensor Threshold Conditioning
The LM2903PSRG4 can convert a low-level analog sensor signal into a logic event by comparing the sensor output with a reference voltage. Its two channels allow separate rising and falling threshold decisions, hysteresis networks, or comparison of two sensing elements. The open-collector output can drive a digital input, optocoupler, relay-driver stage, or status LED through suitable external circuitry. Keep the sensor and reference within the common-mode input range, and connect the comparator ground directly to the signal-reference ground to minimize common-mode errors. Slow transitions near the threshold can cause repeated switching, so add controlled hysteresis where the application permits it and verify the response behavior in the final circuit.
推薦
Industrial Control Interlocks
The LM2903PSRG4 fits industrial interlock and limit-switch conditioning because it combines two independent differential inputs with low supply-current drain. It can compare a sensor contact or conditioned voltage against a system reference and provide an open-collector fault signal. The 8-pin SOIC package is suitable for compact control boards, while the -40°C to +125°C operating range supports extended industrial environments. Include galvanic isolation where required by the safety architecture, and ensure inductive loads are driven by a suitable protection stage rather than the comparator output. PCB layout should keep sensitive input traces short, provide a stable ground reference, and avoid placing high-current switching paths adjacent to the comparison nodes.
推薦
Relay and Optocoupler Interface
The LM2903PSRG4 can provide the decision output used by optocoupler or relay-interface circuits. Because each output is open collector, an external pull-up resistor establishes the inactive high state while the comparator transistor sinks current when its differential input changes state. This arrangement supports isolation-system drive currents and avoids forcing a fixed internal high voltage. Check the absolute maximum output voltage, sink-current rating, and temperature limits before selecting the pull-up network. For relay coils, use a transistor or driver with flyback protection; do not connect a coil directly to a comparator output. The 0.4 mA typical supply drain per comparator also makes the device practical for continuously monitored control systems.
推薦
Automotive Electrical Qualification
The LM2903QDRG4 is the family option to evaluate when an automotive design requires the Q-family qualification, while LM2903PSRG4 serves as the standard PSRG4 ordering configuration. The dual-channel architecture allows two independent threshold decisions in electronic control modules, battery-monitoring subsystems, or actuator-interface circuits. Automotive suitability extends beyond temperature range and includes qualification, traceability, change-control, and supplier-quality requirements. Use the manufacturer ordering information to verify the exact grade and operating range before release. The 36 V maximum supply and open-collector outputs are useful in vehicle electrical environments, but the final design must still satisfy transient, ground-offset, EMC, and output-state requirements.
推薦
推薦產品摘要
工程參考資料,適用於 LM2903PSRG4 — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | LM2903DR | LM2903DBZR | LM2903MX/NOPB | LM2903QDRG4 | LM2903DRG4 |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC |
| Comparator Configuration | Dual differential comparator | Dual differential comparator | Dual differential comparator | Dual differential comparator | Dual differential comparator | Dual differential comparator |
| Number of Channels | 2 | 2 | 2 | 2 | 2 | 2 |
| Output Type | Open collector | Open collector | Open collector | Open collector | Open collector | Open collector |
| Maximum Supply Voltage | 36 V | 36 V | 36 V | 36 V | 36 V | 36 V |
| Supply Current per Comparator | 0.4 mA typical | 0.4 mA typical | 0.4 mA typical | 0.4 mA typical | 0.4 mA typical | 0.4 mA typical |
| Input Bias Current | 25 nA | 25 nA | 25 nA | 25 nA | 25 nA | 25 nA |
| Operating Temperature | -40°C to +125°C | -40°C to +125°C | -40°C to +125°C | -40°C to +125°C | -40°C to +125°C | -40°C to +125°C |
| RoHS Status | Compliant | Compliant | Compliant | Compliant | Compliant | Compliant |
主要差異化特點
- Two independent threshold-monitoring channels in one compact package (對比LM2903DR)
- Automotive-qualified family option is available for qualified designs (對比LM2903QDRG4)
- Wide supply range supports industrial and automotive threshold circuits (對比LM2903MX/NOPB)
設計說明
Do not treat the open-collector output as a push-pull logic output. Each output requires an external pull-up resistor, and the connected node can rise above the comparator supply. Confirm the pull-up voltage against the absolute maximum output rating, size the resistor for the required sink current and rise time, and use a transistor or driver when the load exceeds the comparator's output capability.
Route the inverting and non-inverting inputs away from switching nodes and high-current return paths. Connect the ground reference directly to the comparator ground pin with a short, low-impedance path. Keep the input traces compact, minimize loop area, and place threshold-setting resistors near the relevant input pins to reduce susceptibility to coupled noise and false switching.
Add intentional hysteresis when the compared signals can cross the threshold slowly or with noise. A positive-feedback resistor can establish separate upper and lower switching points, but its value must preserve the required common-mode range and output state. Validate the hysteresis with worst-case input offset, temperature, resistor tolerance, and supply variation rather than relying on a nominal threshold alone.
Calculate the pull-up network's static and switching power before finalizing its resistance. The pull-up creates a DC path when the output transistor is on, while fast transitions dissipate additional energy during charging parasitic capacitance. Confirm that the logic receiving the output can tolerate the selected rise time and that the comparator's sink-current rating remains satisfied at the minimum supply voltage.
合規資訊
RoHS compliance is identified for LM2903PSRG4. The standard PSRG4 configuration is not identified as AEC-Q100 qualified; evaluate the LM2903QDRG4 automotive-qualified family option when automotive qualification is required.