LM2903PSRG4 - Dual Differential Comparator | Texas Instruments
料号: LM2903PSRG4 ✓ 量产中LM2903PSRG4 概述
A differential comparator is a semiconductor amplifier that compares two input voltages and changes its output state when the difference between them crosses a defined threshold. The LM2903 family belongs to the broader hierarchy of analog comparator ICs, analog signal-conditioning ICs, and semiconductor devices. Its two channels can be used independently, allowing one package to monitor two thresholds or control two independent signals.
The principal operating characteristics include a wide supply-voltage range, low supply-current drain independent of supply voltage, and a low input bias current of 25 nA. The open-collector output configuration allows each output to pull a logic signal low while an external pull-up resistor establishes the high state. This makes the device useful in interfaces requiring wired-AND behavior, relay-driver circuits, and systems that need a defined output voltage domain.
The LM2903PSRG4 operates from -40°C to +125°C, supporting industrial temperature environments. Its two independent comparator sections can evaluate separate signal pairs without sharing internal signal paths. Because the outputs are open collector, the maximum output voltage is determined mainly by the pull-up network and external supply rather than by a fixed internal high-level voltage. The 8-pin SOIC footprint supports compact surface-mount layouts in industrial control, instrumentation, power-supply monitoring, and interface circuits.
Typical uses include detecting overvoltage or undervoltage conditions, converting analog sensor thresholds into logic events, monitoring battery or power rails, and driving optocouplers or relay coils through suitable driver stages. The LM2903PSRG4 is particularly appropriate when the monitored signals remain within the comparator's input and supply limits and when an open-collector interface is acceptable.
When designing the circuit, choose the pull-up resistor to balance sink-current capacity, rise time, and power dissipation. Confirm the output current, input common-mode range, input offset voltage, response time, and absolute maximum ratings against the manufacturer datasheet before applying the device to a new voltage range. Account for switching transients and provide stable ground-return paths to prevent comparator chatter.
This product page organizes the LM2903PSRG4 specifications, package information, drop-in family alternatives, application guidance, and engineering design notes. It also provides a structured comparison for selecting a suitable comparator while preserving the same SOIC-8 footprint and pin arrangement.
直接替换替代料: LM2903PSRG4 ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: LM2903PSRG4 (相同外形与封装尺寸) ——差异在于 Package, Operating Temperature Range, Output Type, Number of Channels, Maximum Supply Voltage.
LM2903DR
✅ 直接替换 ⚠️ 规格未核验联系询价
查看数据手册 →LM2903DBZR
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
LM2903MX/NOPB
✅ 直接替换联系询价
查看数据手册 →LM2903QDRG4
✅ 直接替换联系询价
查看数据手册 →LM2903DRG4
✅ 直接替换 ⚠️ 规格未核验联系询价
查看数据手册 →LM2903PSRG4 最大额定值与电气特性
| Comparator Type | Dual differential comparator |
| Number of Channels | 2 channels |
| 输出类型 | Open collector |
| Maximum Supply Voltage | 36 V |
| Dual-Supply Voltage Span | 2 V to 36 V |
| 电源电流 | 0.4 mA typical per comparator |
| Input Bias Current | 25 nA |
| 工作温度 | -40°C to +125°C |
| 封装 | 8-pin SOIC, 5.30 mm width |
| 引脚数 | 8 pins |
| 安装类型 | Surface mount |
| Supply Configuration | Single supply or dual supplies |
| RoHS 状态 | Compliant |
| Logic Output | Open collector, O-COL |
| 电源电压 | 5 V |
LM2903PSRG4 8-pin soic, 5.30 mm width 引脚配置指南
LM2903PSRG4(8-pin soic, 5.30 mm width 封装)的引脚配置。 该模拟元件具有输入、输出和电源引脚。请参阅制造商数据手册以了解失调调零、补偿和使能引脚配置。适用于信号调理和放大器电路。
暂无详细引脚数据: LM2903PSRG4.
请参阅 数据手册 以查看完整引脚配置。
典型应用
LM2903PSRG4 适用于 6 应用s: Power-Supply Overvoltage Detection, Battery Voltage Monitoring, Sensor Threshold Conditioning, Industrial Control Interlocks, Relay and Optocoupler Interface, Automotive Electrical Qualification.
Power-Supply Overvoltage Detection
The LM2903PSRG4 is appropriate for monitoring a DC supply rail with two independent differential channels. Its 36 V maximum supply rating supports applications above the usual 5 V logic level, while the open-collector outputs can pull down an alert or shutdown input through an external pull-up resistor. The two channels can compare a protected rail against an upper threshold and a separate rail against a lower threshold. Before implementation, confirm that every monitored voltage remains within the comparator's input common-mode range and that the pull-up node does not exceed the allowable output voltage. The 0.4 mA typical current per comparator also helps limit the continuous supply burden of always-on protection logic.
推荐
Battery Voltage Monitoring
The LM2903PSRG4 can implement threshold-based battery monitoring by comparing a scaled battery voltage against a reference. Two independent comparator sections provide flexibility for monitoring charge and discharge limits, although the comparator outputs are open collector and therefore require pull-up resistors. The 25 nA input bias current is useful when working with high-impedance divider networks because it minimizes loading of the sensed voltage. The circuit must remain inside the device's input common-mode limits even when the battery voltage is low or the divider ratio changes. Use a resistor divider with appropriately scaled tolerance and verify stability across temperature before treating the output as a dependable battery state indicator.
推荐
Sensor Threshold Conditioning
The LM2903PSRG4 can convert a low-level analog sensor signal into a logic event by comparing the sensor output with a reference voltage. Its two channels allow separate rising and falling threshold decisions, hysteresis networks, or comparison of two sensing elements. The open-collector output can drive a digital input, optocoupler, relay-driver stage, or status LED through suitable external circuitry. Keep the sensor and reference within the common-mode input range, and connect the comparator ground directly to the signal-reference ground to minimize common-mode errors. Slow transitions near the threshold can cause repeated switching, so add controlled hysteresis where the application permits it and verify the response behavior in the final circuit.
推荐
Industrial Control Interlocks
The LM2903PSRG4 fits industrial interlock and limit-switch conditioning because it combines two independent differential inputs with low supply-current drain. It can compare a sensor contact or conditioned voltage against a system reference and provide an open-collector fault signal. The 8-pin SOIC package is suitable for compact control boards, while the -40°C to +125°C operating range supports extended industrial environments. Include galvanic isolation where required by the safety architecture, and ensure inductive loads are driven by a suitable protection stage rather than the comparator output. PCB layout should keep sensitive input traces short, provide a stable ground reference, and avoid placing high-current switching paths adjacent to the comparison nodes.
推荐
Relay and Optocoupler Interface
The LM2903PSRG4 can provide the decision output used by optocoupler or relay-interface circuits. Because each output is open collector, an external pull-up resistor establishes the inactive high state while the comparator transistor sinks current when its differential input changes state. This arrangement supports isolation-system drive currents and avoids forcing a fixed internal high voltage. Check the absolute maximum output voltage, sink-current rating, and temperature limits before selecting the pull-up network. For relay coils, use a transistor or driver with flyback protection; do not connect a coil directly to a comparator output. The 0.4 mA typical supply drain per comparator also makes the device practical for continuously monitored control systems.
推荐
Automotive Electrical Qualification
The LM2903QDRG4 is the family option to evaluate when an automotive design requires the Q-family qualification, while LM2903PSRG4 serves as the standard PSRG4 ordering configuration. The dual-channel architecture allows two independent threshold decisions in electronic control modules, battery-monitoring subsystems, or actuator-interface circuits. Automotive suitability extends beyond temperature range and includes qualification, traceability, change-control, and supplier-quality requirements. Use the manufacturer ordering information to verify the exact grade and operating range before release. The 36 V maximum supply and open-collector outputs are useful in vehicle electrical environments, but the final design must still satisfy transient, ground-offset, EMC, and output-state requirements.
推荐
推荐产品汇总
工程参考数据: LM2903PSRG4 ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | LM2903DR | LM2903DBZR | LM2903MX/NOPB | LM2903QDRG4 | LM2903DRG4 |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC |
| Comparator Configuration | Dual differential comparator | Dual differential comparator | Dual differential comparator | Dual differential comparator | Dual differential comparator | Dual differential comparator |
| Number of Channels | 2 | 2 | 2 | 2 | 2 | 2 |
| Output Type | Open collector | Open collector | Open collector | Open collector | Open collector | Open collector |
| Maximum Supply Voltage | 36 V | 36 V | 36 V | 36 V | 36 V | 36 V |
| Supply Current per Comparator | 0.4 mA typical | 0.4 mA typical | 0.4 mA typical | 0.4 mA typical | 0.4 mA typical | 0.4 mA typical |
| Input Bias Current | 25 nA | 25 nA | 25 nA | 25 nA | 25 nA | 25 nA |
| Operating Temperature | -40°C to +125°C | -40°C to +125°C | -40°C to +125°C | -40°C to +125°C | -40°C to +125°C | -40°C to +125°C |
| RoHS Status | Compliant | Compliant | Compliant | Compliant | Compliant | Compliant |
关键差异点
- Two independent threshold-monitoring channels in one compact package (对比 LM2903DR)
- Automotive-qualified family option is available for qualified designs (对比 LM2903QDRG4)
- Wide supply range supports industrial and automotive threshold circuits (对比 LM2903MX/NOPB)
设计说明
Do not treat the open-collector output as a push-pull logic output. Each output requires an external pull-up resistor, and the connected node can rise above the comparator supply. Confirm the pull-up voltage against the absolute maximum output rating, size the resistor for the required sink current and rise time, and use a transistor or driver when the load exceeds the comparator's output capability.
Route the inverting and non-inverting inputs away from switching nodes and high-current return paths. Connect the ground reference directly to the comparator ground pin with a short, low-impedance path. Keep the input traces compact, minimize loop area, and place threshold-setting resistors near the relevant input pins to reduce susceptibility to coupled noise and false switching.
Add intentional hysteresis when the compared signals can cross the threshold slowly or with noise. A positive-feedback resistor can establish separate upper and lower switching points, but its value must preserve the required common-mode range and output state. Validate the hysteresis with worst-case input offset, temperature, resistor tolerance, and supply variation rather than relying on a nominal threshold alone.
Calculate the pull-up network's static and switching power before finalizing its resistance. The pull-up creates a DC path when the output transistor is on, while fast transitions dissipate additional energy during charging parasitic capacitance. Confirm that the logic receiving the output can tolerate the selected rise time and that the comparator's sink-current rating remains satisfied at the minimum supply voltage.
合规信息
RoHS compliance is identified for LM2903PSRG4. The standard PSRG4 configuration is not identified as AEC-Q100 qualified; evaluate the LM2903QDRG4 automotive-qualified family option when automotive qualification is required.