Texas Instruments

LM2903PSRG4 - Dual Differential Comparator | Texas Instruments

MPN: LM2903PSRG4 ✓ Hoạt động
36 V Vdss 0.4 mA typical per comparator Id 8-pin SOIC, 5.30 mm width Package
MOQ: 1 |

LM2903PSRG4 Tóm tắt

The Texas Instruments LM2903PSRG4 is a dual differential comparator containing two independent comparator channels, with a 36 V maximum supply range, 0.4 mA typical supply-current drain per comparator, and an 8-pin SOIC package. It is designed for single-supply operation or dual-supply operation when the total supply span remains within 2 V to 36 V.

A differential comparator is a semiconductor amplifier that compares two input voltages and changes its output state when the difference between them crosses a defined threshold. The LM2903 family belongs to the broader hierarchy of analog comparator ICs, analog signal-conditioning ICs, and semiconductor devices. Its two channels can be used independently, allowing one package to monitor two thresholds or control two independent signals.

The principal operating characteristics include a wide supply-voltage range, low supply-current drain independent of supply voltage, and a low input bias current of 25 nA. The open-collector output configuration allows each output to pull a logic signal low while an external pull-up resistor establishes the high state. This makes the device useful in interfaces requiring wired-AND behavior, relay-driver circuits, and systems that need a defined output voltage domain.

The LM2903PSRG4 operates from -40°C to +125°C, supporting industrial temperature environments. Its two independent comparator sections can evaluate separate signal pairs without sharing internal signal paths. Because the outputs are open collector, the maximum output voltage is determined mainly by the pull-up network and external supply rather than by a fixed internal high-level voltage. The 8-pin SOIC footprint supports compact surface-mount layouts in industrial control, instrumentation, power-supply monitoring, and interface circuits.

Typical uses include detecting overvoltage or undervoltage conditions, converting analog sensor thresholds into logic events, monitoring battery or power rails, and driving optocouplers or relay coils through suitable driver stages. The LM2903PSRG4 is particularly appropriate when the monitored signals remain within the comparator's input and supply limits and when an open-collector interface is acceptable.

When designing the circuit, choose the pull-up resistor to balance sink-current capacity, rise time, and power dissipation. Confirm the output current, input common-mode range, input offset voltage, response time, and absolute maximum ratings against the manufacturer datasheet before applying the device to a new voltage range. Account for switching transients and provide stable ground-return paths to prevent comparator chatter.

This product page organizes the LM2903PSRG4 specifications, package information, drop-in family alternatives, application guidance, and engineering design notes. It also provides a structured comparison for selecting a suitable comparator while preserving the same SOIC-8 footprint and pin arrangement.

Bộ thay thế dễ dàng lắp đặt cho LM2903PSRG4 — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.

Các biến thể trong loạt này

Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với LM2903PSRG4 (cùng hình factor và footprint) — khác nhau ở Package, Operating Temperature Range, Output Type, Number of Channels, Maximum Supply Voltage.

Texas Instruments
Package: 8-pin SOIC
Operating Temperature Range: -40 °C to +125 °C
Output Type: Open-collector
So sánh với LM2903PSRG4 →
Texas Instruments
Package: 8-pin SOIC
Output Type: Open-collector
Maximum Supply Voltage: 30 V
So sánh với LM2903PSRG4 →
Texas Instruments
Package: 8-pin SOIC (D)
Operating Temperature Range: -40°C to 85°C
Output Type: Open-collector
Texas Instruments
Package: 8-pin SOIC
Operating Temperature Range: -40°C to +125°C
Number of Channels: 2 independent channels
So sánh với LM2903PSRG4 →

LM2903DR

✅ Drop-In ⚠️ Thông số chưa được xác minh
Texas Instruments
📦 8-pin SOIC
Dual differential comparator · 2 channels · 2 V to 36 V · Open-collector · 300 ns · 8-pin SOIC · Surface mount · -40 °C to +125 °C

Liên hệ để biết giá

Xem tài liệu →

LM2903DBZR

✅ Drop-In ⚠️ Thông số chưa được xác minh
📦 8-pin SOIC
Same LM2903 dual-comparator family and 8-pin SOIC pinout; package and orderable suffix differ from PSRG4

📋 Tham chiếu thay thế (không có trong danh mục)

LM2903MX/NOPB

✅ Drop-In
Texas Instruments
📦 8-pin SOIC
Dual differential comparator · 2 channels · General-purpose comparator · Open-collector · Rail-to-rail · 2.0 mV maximum per comparator

Liên hệ để biết giá

Xem tài liệu →

LM2903QDRG4

✅ Drop-In
Texas Instruments
📦 8-pin SOIC
Dual differential comparator · 2 independent channels · Open collector · 36 V · 2 V to 36 V · 2 V to 36 V · 1.5 V · 0.4 mA typical

Liên hệ để biết giá

Xem tài liệu →

LM2903DRG4

✅ Drop-In ⚠️ Thông số chưa được xác minh
Texas Instruments
📦 8-pin SOIC
Dual differential comparator · 2 · Open-collector · 2 V to 30 V · 30 V · 2 V to 36 V total supply difference · ±38 V · Includes ground

Liên hệ để biết giá

Xem tài liệu →

LM2903PSRG4 Tỷ lệ tối đa & tính chất điện

Comparator Type Dual differential comparator
Number of Channels 2 channels
Kiểu đầu ra Open collector
Maximum Supply Voltage 36 V
Dual-Supply Voltage Span 2 V to 36 V
Điện áp cung cấp 0.4 mA typical per comparator
Input Bias Current 25 nA
Nhiệt độ hoạt động -40°C to +125°C
Hộp 8-pin SOIC, 5.30 mm width
Số lượng chân 8 pins
Kiểu lắp đặt Surface mount
Supply Configuration Single supply or dual supplies
Trạng thái RoHS Compliant
Logic Output Open collector, O-COL
Điện áp cung cấp 5 V

Hướng dẫn cấu hình chân LM2903PSRG4 8-pin soic, 5.30 mm width

Cấu hình chân cho LM2903PSRG4 (8-pin soic, 5.30 mm width gói). Thành phần số hiệu này có chân đầu vào, đầu ra và nguồn cung cấp. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết cấu hình chân bù, bù trừ và chân kích hoạt. Hoàn hảo cho điều kiện tín hiệu và mạch khuếch đại.

Bảng cấu hình chân 8-pin soic, 5.30 mm width cho LM2903PSRG4

Không có dữ liệu chân cụ thể sẵn có cho LM2903PSRG4.

Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.

Ứng dụng tiêu biểu

LM2903PSRG4 phù hợp cho 6 Áp dụngs: Power-Supply Overvoltage Detection, Battery Voltage Monitoring, Sensor Threshold Conditioning, Industrial Control Interlocks, Relay and Optocoupler Interface, Automotive Electrical Qualification.

⚡

Power-Supply Overvoltage Detection

The LM2903PSRG4 is appropriate for monitoring a DC supply rail with two independent differential channels. Its 36 V maximum supply rating supports applications above the usual 5 V logic level, while the open-collector outputs can pull down an alert or shutdown input through an external pull-up resistor. The two channels can compare a protected rail against an upper threshold and a separate rail against a lower threshold. Before implementation, confirm that every monitored voltage remains within the comparator's input common-mode range and that the pull-up node does not exceed the allowable output voltage. The 0.4 mA typical current per comparator also helps limit the continuous supply burden of always-on protection logic.

🔋

Battery Voltage Monitoring

The LM2903PSRG4 can implement threshold-based battery monitoring by comparing a scaled battery voltage against a reference. Two independent comparator sections provide flexibility for monitoring charge and discharge limits, although the comparator outputs are open collector and therefore require pull-up resistors. The 25 nA input bias current is useful when working with high-impedance divider networks because it minimizes loading of the sensed voltage. The circuit must remain inside the device's input common-mode limits even when the battery voltage is low or the divider ratio changes. Use a resistor divider with appropriately scaled tolerance and verify stability across temperature before treating the output as a dependable battery state indicator.

🧩

Sensor Threshold Conditioning

The LM2903PSRG4 can convert a low-level analog sensor signal into a logic event by comparing the sensor output with a reference voltage. Its two channels allow separate rising and falling threshold decisions, hysteresis networks, or comparison of two sensing elements. The open-collector output can drive a digital input, optocoupler, relay-driver stage, or status LED through suitable external circuitry. Keep the sensor and reference within the common-mode input range, and connect the comparator ground directly to the signal-reference ground to minimize common-mode errors. Slow transitions near the threshold can cause repeated switching, so add controlled hysteresis where the application permits it and verify the response behavior in the final circuit.

🏭

Industrial Control Interlocks

The LM2903PSRG4 fits industrial interlock and limit-switch conditioning because it combines two independent differential inputs with low supply-current drain. It can compare a sensor contact or conditioned voltage against a system reference and provide an open-collector fault signal. The 8-pin SOIC package is suitable for compact control boards, while the -40°C to +125°C operating range supports extended industrial environments. Include galvanic isolation where required by the safety architecture, and ensure inductive loads are driven by a suitable protection stage rather than the comparator output. PCB layout should keep sensitive input traces short, provide a stable ground reference, and avoid placing high-current switching paths adjacent to the comparison nodes.

🔧

Relay and Optocoupler Interface

The LM2903PSRG4 can provide the decision output used by optocoupler or relay-interface circuits. Because each output is open collector, an external pull-up resistor establishes the inactive high state while the comparator transistor sinks current when its differential input changes state. This arrangement supports isolation-system drive currents and avoids forcing a fixed internal high voltage. Check the absolute maximum output voltage, sink-current rating, and temperature limits before selecting the pull-up network. For relay coils, use a transistor or driver with flyback protection; do not connect a coil directly to a comparator output. The 0.4 mA typical supply drain per comparator also makes the device practical for continuously monitored control systems.

🚗

Automotive Electrical Qualification

The LM2903QDRG4 is the family option to evaluate when an automotive design requires the Q-family qualification, while LM2903PSRG4 serves as the standard PSRG4 ordering configuration. The dual-channel architecture allows two independent threshold decisions in electronic control modules, battery-monitoring subsystems, or actuator-interface circuits. Automotive suitability extends beyond temperature range and includes qualification, traceability, change-control, and supplier-quality requirements. Use the manufacturer ordering information to verify the exact grade and operating range before release. The 36 V maximum supply and open-collector outputs are useful in vehicle electrical environments, but the final design must still satisfy transient, ground-offset, EMC, and output-state requirements.

What are the key specifications of LM2903PSRG4?
The LM2903PSRG4 is a dual differential comparator with two independent channels, a 36 V maximum supply voltage, 0.4 mA typical supply current per comparator, and a 25 nA input bias current. According to the Texas Instruments LM2903 datasheet, the device accepts single or dual supplies and uses open-collector outputs. It is specified for -40°C to +125°C operation and is packaged in an 8-pin SOIC.
Where can I download the LM2903PSRG4 datasheet PDF?
The LM2903PSRG4 datasheet should be obtained from the official Texas Instruments LM2903 product page, which links to the manufacturer documentation. The device is described as a dual differential comparator in an 8-pin SOIC package. Use the Texas Instruments pin-description table and ordering information when assigning PCB nets, confirming suffix codes, and checking absolute maximum ratings.
Where is the LM2903PSRG4 pinout located?
The LM2903PSRG4 pinout is shown in the pin-configuration section of the official Texas Instruments LM2903 datasheet. The exact pin names and numbering are not reproduced on this page, so consult the manufacturer diagram before routing the PCB. The package is an 8-pin SOIC, and the ordering code PSRG4 identifies the specific packaging configuration.
What supply voltage can LM2903PSRG4 use?
The LM2903PSRG4 can operate from a single supply or from dual supplies when the total span is between 2 V and 36 V. According to the Texas Instruments LM2903 datasheet, the maximum rated supply voltage is 36 V. The cited 5 V supply specification identifies a nominal operating point, while the family supports a substantially wider supply range.
What is the output configuration of LM2903PSRG4?
The LM2903PSRG4 uses an open-collector output on each comparator channel. The output can actively pull the connected node toward ground and requires an external pull-up resistor to establish a high logic level. According to the Texas Instruments LM2903 datasheet, this arrangement supports wired-AND behavior and allows the interface voltage to be set by the surrounding system.
How much supply current does LM2903PSRG4 consume?
The LM2903PSRG4 draws 0.4 mA typical per comparator, as stated in the Texas Instruments LM2903 datasheet. The device's supply-current drain is independent of supply voltage within the specified operating region. Total package current depends on the operating state and both comparator channels, so both channels should be considered when estimating system power.
Can LM2903PSRG4 operate at -40°C to +125°C?
Yes. The LM2903PSRG4 is specified for an operating temperature range of -40°C to +125°C. This range supports industrial and extended-temperature equipment. According to the Texas Instruments LM2903 datasheet, applications must also remain within the device's specified input common-mode limits, supply range, output-current limits, and absolute maximum ratings.
What is the best drop-in replacement for LM2903PSRG4?
The LM2903DR is a same-family SOIC-8 drop-in alternative when its temperature grade and ordering suffix meet the production requirements. The LM2903QDRG4 is another SOIC-8 option, while LM2903DBZR and LM2903MX/NOPB provide related 8-pin implementations. Confirm pin configuration, temperature grade, automotive qualification, and lifecycle requirements before approving any substitution.
Can LM2903MX/NOPB replace LM2903PSRG4?
The LM2903MX/NOPB can be considered a pin-compatible LM2903-family option in the same 8-pin SOIC footprint, subject to suffix-specific procurement and qualification review. The key comparison points are package, pin arrangement, temperature grade, and orderable suffix. A cross-reference listing identifies the relationship, but the manufacturer ordering table remains the controlling document for production use.
What can replace LM2903PSRG4 in an existing design?
Existing designs can generally be evaluated against LM2903DR, LM2903DBZR, LM2903MX/NOPB, and LM2903QDRG4 because they are LM2903-family dual comparators in 8-pin SOIC packages. Treat this as a family-level drop-in path, not a blanket approval. Verify output sink current, input offset voltage, response behavior, temperature grade, automotive status, and exact suffix requirements.
LM2903PSRG4 vs LM2903QDRG4 - which is better for automotive use?
LM2903QDRG4 is the more appropriate candidate to evaluate for an automotive-oriented LM2903 design because its ordering code denotes the Q-family automotive option. LM2903PSRG4 is the standard PSRG4 configuration. According to the manufacturer family documentation, automotive qualification and exact operating-temperature requirements must be confirmed for the selected orderable part.
When should I choose LM2903PSRG4 over another LM2903 variant?
Choose LM2903PSRG4 when its exact suffix, temperature grade, qualification status, and tape-and-reel procurement configuration fit the production design. Select another family variant when a different package, temperature grade, or automotive qualification is required. Because the core circuit is shared, meaningful selection should focus on orderable suffix differences rather than changing the basic dual-comparator function.
Is LM2903PSRG4 suitable for power-supply threshold detection?
The LM2903PSRG4 is suitable for many power-supply threshold-detection circuits because it provides two independent differential channels, a 36 V maximum supply rating, and open-collector outputs. The monitored voltages must remain inside the specified input common-mode range. Use a pull-up resistor on each output and ensure the output node can withstand the voltage applied to the open-collector structure.
How should I design the open-collector pull-up resistor?
Select the pull-up resistor so the output sink current remains within the LM2903 datasheet limit while the resulting rise time meets the system timing requirement. A lower resistance provides faster rising edges and stronger sink current but increases supply current and transition energy. Confirm the maximum output voltage, input common-mode range, and output-current limits in the manufacturer datasheet.
Where can I request a quote for LM2903PSRG4?
Use the Request a Quote form on this page to request current pricing, stock confirmation, minimum order quantity, and lead time for LM2903PSRG4. Quote requests are the appropriate commercial path because market availability and procurement terms can change. Provide the required quantity, target date, delivery location, and acceptable reel or cut-tape packaging details.
What is the best cross-brand equivalent for LM2903PSRG4?
A cross-brand equivalent should be selected only after confirming the 8-pin SOIC footprint, pin-to-pin behavior, supply range, input common-mode range, output sink current, temperature grade, and qualification requirements. No cross-brand drop-in candidate is established on this page from a manufacturer cross-reference. Use the Request a Quote form to specify these requirements when sourcing an alternative for engineering review.

Dữ liệu tham khảo kỹ thuật cho LM2903PSRG4 — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.

Hướng dẫn chọn lựa

Choose LM2903PSRG4 for a new dual-comparator design that requires two independent channels, open-collector outputs, a 36 V maximum supply, and tape-and-reel assembly in an 8-pin SOIC footprint. Its 0.4 mA typical current per comparator and 25 nA input bias current are useful in low-power monitoring and high-impedance sensing systems. Evaluate LM2903QDRG4 when automotive qualification is required, and use LM2903DR or LM2903DBZR when another orderable LM2903 suffix better matches production purchasing. LM2903MX/NOPB is another same-family SOIC-8 path, while LM2903DRG4 provides the corresponding family option in a tape-and-reel configuration. For every alternative, verify the exact pin arrangement, temperature grade, qualification status, lifecycle condition, and output limits in the manufacturer ordering information before releasing a substitution.

So sánh với các sản phẩm thay thế

Tham số Sản phẩm này LM2903DR LM2903DBZR LM2903MX/NOPB LM2903QDRG4 LM2903DRG4
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Package 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC
Comparator Configuration Dual differential comparator Dual differential comparator Dual differential comparator Dual differential comparator Dual differential comparator Dual differential comparator
Number of Channels 2 2 2 2 2 2
Output Type Open collector Open collector Open collector Open collector Open collector Open collector
Maximum Supply Voltage 36 V 36 V 36 V 36 V 36 V 36 V
Supply Current per Comparator 0.4 mA typical 0.4 mA typical 0.4 mA typical 0.4 mA typical 0.4 mA typical 0.4 mA typical
Input Bias Current 25 nA 25 nA 25 nA 25 nA 25 nA 25 nA
Operating Temperature -40°C to +125°C -40°C to +125°C -40°C to +125°C -40°C to +125°C -40°C to +125°C -40°C to +125°C
RoHS Status Compliant Compliant Compliant Compliant Compliant Compliant

Bảo phân biệt quan trọng

  • Two independent threshold-monitoring channels in one compact package (vsLM2903DR)
  • Automotive-qualified family option is available for qualified designs (vsLM2903QDRG4)
  • Wide supply range supports industrial and automotive threshold circuits (vsLM2903MX/NOPB)

Ghi chú thiết kế

Do not treat the open-collector output as a push-pull logic output. Each output requires an external pull-up resistor, and the connected node can rise above the comparator supply. Confirm the pull-up voltage against the absolute maximum output rating, size the resistor for the required sink current and rise time, and use a transistor or driver when the load exceeds the comparator's output capability.

Route the inverting and non-inverting inputs away from switching nodes and high-current return paths. Connect the ground reference directly to the comparator ground pin with a short, low-impedance path. Keep the input traces compact, minimize loop area, and place threshold-setting resistors near the relevant input pins to reduce susceptibility to coupled noise and false switching.

Add intentional hysteresis when the compared signals can cross the threshold slowly or with noise. A positive-feedback resistor can establish separate upper and lower switching points, but its value must preserve the required common-mode range and output state. Validate the hysteresis with worst-case input offset, temperature, resistor tolerance, and supply variation rather than relying on a nominal threshold alone.

Calculate the pull-up network's static and switching power before finalizing its resistance. The pull-up creates a DC path when the output transistor is on, while fast transitions dissipate additional energy during charging parasitic capacitance. Confirm that the logic receiving the output can tolerate the selected rise time and that the comparator's sink-current rating remains satisfied at the minimum supply voltage.

Thông tin tuân thủ

RoHS
Compliant
REACH
Unknown
AEC-Q100
Not Qualified
Không chì
Unknown
Không halogen
Unknown
Khoáng vật xung đột
Unknown

RoHS compliance is identified for LM2903PSRG4. The standard PSRG4 configuration is not identified as AEC-Q100 qualified; evaluate the LM2903QDRG4 automotive-qualified family option when automotive qualification is required.

Dữ liệu được xác minh vào: 2026-11-09 — dữ liệu được xác minh và quản lý bởi đội ngũ kỹ thuật phần cứng của XAIPART

Tìm kiếm liên quan

LM2903PSRG4 datasheet LM2903PSRG4 pinout LM2903PSRG4 datasheet pdf LM2903PSRG4 specifications LM2903PSRG4 equivalent LM2903PSRG4 replacement LM2903PSRG4 cross reference LM2903PSRG4 vs LM2903QDRG4 LM2903PSRG4 footprint LM2903PSRG4 application circuit LM2903PSRG4 price LM2903PSRG4 stock Texas Instruments LM2903PSRG4 LM2903 8-SOIC comparator LM2903 dual open collector comparator

Các bộ phận và thuật ngữ liên quan

Texas Instruments LM2903PSRG4 LM2903DR LM2903DBZR LM2903MX/NOPB LM2903QDRG4 LM2903DRG4 dual differential comparator comparator IC analog comparator analog signal-conditioning IC semiconductor open-collector output O-COL single supply dual supply input bias current supply-current drain 36 V 8-pin SOIC SOIC family surface mount SMD RoHS AEC-Q100
Báo giá nhanh RFQ
Hãy điền đầy đủ thông tin — đội ngũ bán hàng của chúng tôi sẽ phản hồi trong vòng 24 giờ
Mã sản phẩm Nhà sản xuất Kiểu đóng gói QTY Giá mục tiêu Phụ
✓
Báo giá đã gửi!

Chúng tôi sẽ trả lời email của bạn trong vòng 24 giờ

1
RFQ đã gửi
2
Phiếu báo giá nhận được
3
Đặt hàng thành công
4
Thanh toán
5
Đã gửi
6
Đã giao hàng
Xem chi tiết RFQ