LM2903PSRG4 - Dual Differential Comparator | Texas Instruments
MPN: LM2903PSRG4 ✓ פעילLM2903PSRG4 סקירה
A differential comparator is a semiconductor amplifier that compares two input voltages and changes its output state when the difference between them crosses a defined threshold. The LM2903 family belongs to the broader hierarchy of analog comparator ICs, analog signal-conditioning ICs, and semiconductor devices. Its two channels can be used independently, allowing one package to monitor two thresholds or control two independent signals.
The principal operating characteristics include a wide supply-voltage range, low supply-current drain independent of supply voltage, and a low input bias current of 25 nA. The open-collector output configuration allows each output to pull a logic signal low while an external pull-up resistor establishes the high state. This makes the device useful in interfaces requiring wired-AND behavior, relay-driver circuits, and systems that need a defined output voltage domain.
The LM2903PSRG4 operates from -40°C to +125°C, supporting industrial temperature environments. Its two independent comparator sections can evaluate separate signal pairs without sharing internal signal paths. Because the outputs are open collector, the maximum output voltage is determined mainly by the pull-up network and external supply rather than by a fixed internal high-level voltage. The 8-pin SOIC footprint supports compact surface-mount layouts in industrial control, instrumentation, power-supply monitoring, and interface circuits.
Typical uses include detecting overvoltage or undervoltage conditions, converting analog sensor thresholds into logic events, monitoring battery or power rails, and driving optocouplers or relay coils through suitable driver stages. The LM2903PSRG4 is particularly appropriate when the monitored signals remain within the comparator's input and supply limits and when an open-collector interface is acceptable.
When designing the circuit, choose the pull-up resistor to balance sink-current capacity, rise time, and power dissipation. Confirm the output current, input common-mode range, input offset voltage, response time, and absolute maximum ratings against the manufacturer datasheet before applying the device to a new voltage range. Account for switching transients and provide stable ground-return paths to prevent comparator chatter.
This product page organizes the LM2903PSRG4 specifications, package information, drop-in family alternatives, application guidance, and engineering design notes. It also provides a structured comparison for selecting a suitable comparator while preserving the same SOIC-8 footprint and pin arrangement.
חלופות תחליף ישיר עבור LM2903PSRG4 — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.
וריאנטים בסדרה זו
דגמים מאותה סדרה התואמים Drop-in עם LM2903PSRG4 (אותו גורם צורה וטביעת רגל) — שונים ב Package, Operating Temperature Range, Output Type, Number of Channels, Maximum Supply Voltage.
LM2903DR
✅ Drop-In ⚠️ מפרטים לא מאומתיםצור קשר לקבלת מחיר
הצג גיליון נתונים ←LM2903DBZR
✅ Drop-In ⚠️ מפרטים לא מאומתים📋 חלופה להתייחסות (לא בקטלוג)
LM2903MX/NOPB
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←LM2903QDRG4
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←LM2903DRG4
✅ Drop-In ⚠️ מפרטים לא מאומתיםצור קשר לקבלת מחיר
הצג גיליון נתונים ←LM2903PSRG4 דירוגים מרביים ומאפיינים חשמליים
| Comparator Type | Dual differential comparator |
| Number of Channels | 2 channels |
| סוג פלט | Open collector |
| Maximum Supply Voltage | 36 V |
| Dual-Supply Voltage Span | 2 V to 36 V |
| זרם אספקה | 0.4 mA typical per comparator |
| Input Bias Current | 25 nA |
| טמפרטורת פעולה | -40°C to +125°C |
| מארז | 8-pin SOIC, 5.30 mm width |
| מספר פינים | 8 pins |
| סוג הרכבה | Surface mount |
| Supply Configuration | Single supply or dual supplies |
| סטטוס RoHS | Compliant |
| Logic Output | Open collector, O-COL |
| מתח אספקה | 5 V |
מדריך תצורת פינים של LM2903PSRG4 8-pin soic, 5.30 mm width
תצורת פינים עבור LM2903PSRG4 (מארזת 8-pin soic, 5.30 mm width). רכיב אנלוגי זה כולל פיני כניסה, יציאה ואספקת מתח. יש לעיין בגיליון הנתונים של היצרן לתצורות פיני איפוס היסט, פיצוי והפעלה. אידיאלי למעגלי עיצוב אותות ומגברים.
אין נתוני פריסת פינים מפורטים עבור LM2903PSRG4.
עיינו ב- גיליון נתונים עבור תצורת פינים מלאה.
יישומים טיפוסיים
LM2903PSRG4 מתאים עבור 6 יישוםs: Power-Supply Overvoltage Detection, Battery Voltage Monitoring, Sensor Threshold Conditioning, Industrial Control Interlocks, Relay and Optocoupler Interface, Automotive Electrical Qualification.
Power-Supply Overvoltage Detection
The LM2903PSRG4 is appropriate for monitoring a DC supply rail with two independent differential channels. Its 36 V maximum supply rating supports applications above the usual 5 V logic level, while the open-collector outputs can pull down an alert or shutdown input through an external pull-up resistor. The two channels can compare a protected rail against an upper threshold and a separate rail against a lower threshold. Before implementation, confirm that every monitored voltage remains within the comparator's input common-mode range and that the pull-up node does not exceed the allowable output voltage. The 0.4 mA typical current per comparator also helps limit the continuous supply burden of always-on protection logic.
מומלץ
Battery Voltage Monitoring
The LM2903PSRG4 can implement threshold-based battery monitoring by comparing a scaled battery voltage against a reference. Two independent comparator sections provide flexibility for monitoring charge and discharge limits, although the comparator outputs are open collector and therefore require pull-up resistors. The 25 nA input bias current is useful when working with high-impedance divider networks because it minimizes loading of the sensed voltage. The circuit must remain inside the device's input common-mode limits even when the battery voltage is low or the divider ratio changes. Use a resistor divider with appropriately scaled tolerance and verify stability across temperature before treating the output as a dependable battery state indicator.
מומלץ
Sensor Threshold Conditioning
The LM2903PSRG4 can convert a low-level analog sensor signal into a logic event by comparing the sensor output with a reference voltage. Its two channels allow separate rising and falling threshold decisions, hysteresis networks, or comparison of two sensing elements. The open-collector output can drive a digital input, optocoupler, relay-driver stage, or status LED through suitable external circuitry. Keep the sensor and reference within the common-mode input range, and connect the comparator ground directly to the signal-reference ground to minimize common-mode errors. Slow transitions near the threshold can cause repeated switching, so add controlled hysteresis where the application permits it and verify the response behavior in the final circuit.
מומלץ
Industrial Control Interlocks
The LM2903PSRG4 fits industrial interlock and limit-switch conditioning because it combines two independent differential inputs with low supply-current drain. It can compare a sensor contact or conditioned voltage against a system reference and provide an open-collector fault signal. The 8-pin SOIC package is suitable for compact control boards, while the -40°C to +125°C operating range supports extended industrial environments. Include galvanic isolation where required by the safety architecture, and ensure inductive loads are driven by a suitable protection stage rather than the comparator output. PCB layout should keep sensitive input traces short, provide a stable ground reference, and avoid placing high-current switching paths adjacent to the comparison nodes.
מומלץ
Relay and Optocoupler Interface
The LM2903PSRG4 can provide the decision output used by optocoupler or relay-interface circuits. Because each output is open collector, an external pull-up resistor establishes the inactive high state while the comparator transistor sinks current when its differential input changes state. This arrangement supports isolation-system drive currents and avoids forcing a fixed internal high voltage. Check the absolute maximum output voltage, sink-current rating, and temperature limits before selecting the pull-up network. For relay coils, use a transistor or driver with flyback protection; do not connect a coil directly to a comparator output. The 0.4 mA typical supply drain per comparator also makes the device practical for continuously monitored control systems.
מומלץ
Automotive Electrical Qualification
The LM2903QDRG4 is the family option to evaluate when an automotive design requires the Q-family qualification, while LM2903PSRG4 serves as the standard PSRG4 ordering configuration. The dual-channel architecture allows two independent threshold decisions in electronic control modules, battery-monitoring subsystems, or actuator-interface circuits. Automotive suitability extends beyond temperature range and includes qualification, traceability, change-control, and supplier-quality requirements. Use the manufacturer ordering information to verify the exact grade and operating range before release. The 36 V maximum supply and open-collector outputs are useful in vehicle electrical environments, but the final design must still satisfy transient, ground-offset, EMC, and output-state requirements.
מומלץ
סיכום מוצרים מומלצים
נתוני עזר הנדסיים עבור LM2903PSRG4 — השוואה, הנחיות תכנון ומידע על תאימות.
מדריך בחירה
השוואה עם חלופות
| פרמטר | מוצר זה | LM2903DR | LM2903DBZR | LM2903MX/NOPB | LM2903QDRG4 | LM2903DRG4 |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC |
| Comparator Configuration | Dual differential comparator | Dual differential comparator | Dual differential comparator | Dual differential comparator | Dual differential comparator | Dual differential comparator |
| Number of Channels | 2 | 2 | 2 | 2 | 2 | 2 |
| Output Type | Open collector | Open collector | Open collector | Open collector | Open collector | Open collector |
| Maximum Supply Voltage | 36 V | 36 V | 36 V | 36 V | 36 V | 36 V |
| Supply Current per Comparator | 0.4 mA typical | 0.4 mA typical | 0.4 mA typical | 0.4 mA typical | 0.4 mA typical | 0.4 mA typical |
| Input Bias Current | 25 nA | 25 nA | 25 nA | 25 nA | 25 nA | 25 nA |
| Operating Temperature | -40°C to +125°C | -40°C to +125°C | -40°C to +125°C | -40°C to +125°C | -40°C to +125°C | -40°C to +125°C |
| RoHS Status | Compliant | Compliant | Compliant | Compliant | Compliant | Compliant |
מבדילים עיקריים
- Two independent threshold-monitoring channels in one compact package (לעומתLM2903DR)
- Automotive-qualified family option is available for qualified designs (לעומתLM2903QDRG4)
- Wide supply range supports industrial and automotive threshold circuits (לעומתLM2903MX/NOPB)
הערות תכנון
Do not treat the open-collector output as a push-pull logic output. Each output requires an external pull-up resistor, and the connected node can rise above the comparator supply. Confirm the pull-up voltage against the absolute maximum output rating, size the resistor for the required sink current and rise time, and use a transistor or driver when the load exceeds the comparator's output capability.
Route the inverting and non-inverting inputs away from switching nodes and high-current return paths. Connect the ground reference directly to the comparator ground pin with a short, low-impedance path. Keep the input traces compact, minimize loop area, and place threshold-setting resistors near the relevant input pins to reduce susceptibility to coupled noise and false switching.
Add intentional hysteresis when the compared signals can cross the threshold slowly or with noise. A positive-feedback resistor can establish separate upper and lower switching points, but its value must preserve the required common-mode range and output state. Validate the hysteresis with worst-case input offset, temperature, resistor tolerance, and supply variation rather than relying on a nominal threshold alone.
Calculate the pull-up network's static and switching power before finalizing its resistance. The pull-up creates a DC path when the output transistor is on, while fast transitions dissipate additional energy during charging parasitic capacitance. Confirm that the logic receiving the output can tolerate the selected rise time and that the comparator's sink-current rating remains satisfied at the minimum supply voltage.
מידע על תאימות
RoHS compliance is identified for LM2903PSRG4. The standard PSRG4 configuration is not identified as AEC-Q100 qualified; evaluate the LM2903QDRG4 automotive-qualified family option when automotive qualification is required.