LM2904WHYDT - Dual General-Purpose Op Amp | STMicroelectronics
MPN: LM2904WHYDT ✓ 啟用中LM2904WHYDT 概覽
An operational amplifier is an analog integrated circuit that amplifies the difference between its inverting and non-inverting inputs. The op-amp category sits within analog signal-chain ICs and serves as a fundamental building block for sensors, filters, buffers, comparators, and closed-loop control systems. The LM2904 family combines internal frequency compensation with two amplifiers in one package, reducing board area compared with separate single-channel devices while preserving independent channels.
The LM2904WHYDT is identified as a standard general-purpose amplifier with two single-ended circuits. Its internally compensated architecture allows operation without an external compensation network in many conventional closed-loop configurations. The device is intended for low-power applications and is particularly useful where a compact, general-purpose dual amplifier is preferable to a high-speed precision amplifier. The exact input offset, bandwidth, output-current, and temperature limits should be confirmed from the manufacturer datasheet before final circuit sign-off.
Two independent channels can implement voltage followers, transimpedance stages, differential amplifiers, active filters, comparators, and motor or actuator-control loops. A common application is conditioning the output of a bridge sensor, potentiometer, or resistive divider before an ADC samples the signal. In automotive systems, the dual format can economize PCB space in body, climate, or powertrain-control modules where multiple low-power analog channels are required.
The SOIC-8 package supports conventional surface-mount assembly and is suitable for lead-free production boards. Place each power pin close to a low-impedance decoupling network and route sensitive input traces away from switching nodes. Because the amplifiers are independent rather than sharing internal signal paths, grounding and supply layout should be designed to minimize channel-to-channel coupling. Verify the exposed operating limits and decoupling recommendations in the manufacturer datasheet for the exact automotive temperature grade.
This page combines the manufacturer listing, distributor package identification, sourcing information, pin-compatible alternatives, and practical analog-design guidance. Use the Request a Quote form for current availability, lead time, and commercial terms, and use the official datasheet for authoritative electrical limits before layout release.
直接替換替代品,適用於 LM2904WHYDT — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: LM2904WHYDT (相同外形與佔位) — 差異在於 Package, Amplifier Type, Number of Channels, Gain-Bandwidth Product, Input Offset Voltage.
LM2904BIDR
✅ 直接替換聯絡詢價
查看資料表 →LM2904BA
✅ 直接替換📋 參考替代品(不在目錄中)
LM2904D
✅ 直接替換聯絡詢價
查看資料表 →LM2904WHYDT 最大額定值與電氣特性
| Product Type | Dual general-purpose operational amplifier |
| Number of Amplifiers | 2 circuits |
| Channel Configuration | 2 independent single-ended amplifiers |
| Internal Frequency Compensation | Implemented internally |
| 封裝 | 8-SOIC |
| 安裝類型 | Surface mount |
| Supply Configuration | Single supply or split supply |
LM2904WHYDT 8-soic 腳位配置指南
LM2904WHYDT(8-soic 封裝)的腳位配置。 此類比元件具有輸入、輸出與電源腳位。偏移歸零、補償與致能腳位配置請參閱製造商資料表。適用於訊號調理與放大器電路。
無詳細腳位定義資料: LM2904WHYDT.
請參閱 資料表 以查看完整腳位配置。
典型應用
LM2904WHYDT 適用於 6 應用s: Automotive Sensor Signal Conditioning, Industrial Instrumentation Amplification, Active Audio and Low-Frequency Filters, Battery-Powered Control and Monitor Circuits, Motor Actuator Control Interfaces, Power Supply Feedback and Load Monitoring.
Automotive Sensor Signal Conditioning
The LM2904WHYDT fits low-power automotive sensing stages that require two independent analog channels in a compact 8-SOIC package. Two amplifiers can condition a bridge or resistive sensor and provide signal buffering or active filtering without adding two separate single-op-amp packages. Its general-purpose internally compensated architecture supports conventional closed-loop analog designs. Before releasing the circuit, verify the exact automotive grade, operating-temperature range, input common-mode limits, output swing, and offset against the manufacturer datasheet. The final selection must also preserve the sensor excitation range and signal-to-error budget.
推薦
Industrial Instrumentation Amplification
The LM2904WHYDT is suitable for industrial instrumentation front ends where two channels must amplify differential sensor signals with limited board area. One channel can perform the differential input stage while the other provides inversion, filtering, or output buffering. The device description identifies automotive and industrial control systems as intended markets and confirms two independent, internally compensated circuits. Check input-bias-current and common-mode requirements against high-impedance transducers, and confirm that output swing and gain-bandwidth product preserve required accuracy and settling behavior.
推薦
Active Audio and Low-Frequency Filters
Two independent LM2904WHYDT channels can form Sallen-Key or multiple-feedback active filters, tone controls, and low-frequency signal shapers. Internal frequency compensation simplifies conventional gain stages, while the dual package reduces component count and PCB area. The amplifier must remain within its input common-mode range, output swing, and gain-bandwidth limits throughout the passband and stopband. Validate stability with the actual source and load impedances, because capacitive loading and high closed-loop gain can affect the usable response even when the nominal pin arrangement is unchanged.
推薦
Battery-Powered Control and Monitor Circuits
The LM2904WHYDT is appropriate for battery-operated monitoring and control electronics that need two low-power amplifier channels without a high-bandwidth device. It can implement a voltage follower for a sensor, a comparator-style threshold stage, or a slow closed-loop control amplifier. Its dual configuration supports channel independence while keeping the external component count low. Verify supply current, input behavior near the lower rail, output swing, and common-mode range under the minimum battery voltage, because these operating conditions determine whether the circuit remains functional at end of discharge.
推薦
Motor Actuator Control Interfaces
The LM2904WHYDT can serve as an interface in motor and actuator-control systems by buffering command signals, amplifying position-sensor feedback, or conditioning an analog command into a control loop. Two independent channels allow command and feedback paths to be handled in one SOIC-8 device. Its general-purpose architecture is suitable for slow feedback loops rather than demanding motor-drive timing. Confirm output-current capability, output swing, stability with capacitive loads, and supply range, and provide local decoupling and careful routing to prevent switching transients from entering the analog path.
推薦
Power Supply Feedback and Load Monitoring
The LM2904WHYDT can monitor an output rail by buffering the midpoint of a resistor divider and comparing the conditioned level with a reference or ADC input. A second channel can monitor another rail or amplify a current-sense signal. The dual, low-power format makes it useful in compact supply-control and protection modules. Because it is not a precision part by default, calculate the resistor-divider error, amplifier offset, bias-current contribution, and output accuracy. The circuit must also keep the monitored node within the amplifier's input common-mode range at every expected operating condition.
推薦
推薦產品摘要
工程參考資料,適用於 LM2904WHYDT — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | LM2904B | LM2904BA | LM2904D | LM2904QDR | LM2904DT |
|---|---|---|---|---|---|---|
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics | NXP Semiconductors | Texas Instruments | STMicroelectronics |
| Package | 8-SOIC | SOIC-8 | SOIC-8 | SOIC-8 | SOIC-8 | SOIC-8 |
| Amplifier Count | 2 circuits | 2 circuits | 2 circuits | 2 circuits | 2 circuits | 2 circuits |
| Internal Frequency Compensation | Implemented internally | Implemented internally | Implemented internally | Implemented internally | Implemented internally | Implemented internally |
| Product Positioning | Standard general-purpose dual amplifier | Newer LM2904-family dual amplifier | Newer LM2904-family dual amplifier | General-purpose dual amplifier | Automotive-oriented dual amplifier | General-purpose dual amplifier |
| Supply Configuration | Single supply or split supply | Single supply or split supply | Single supply or split supply | Single supply or split supply | Single supply or split supply | Single supply or split supply |
主要差異化特點
- Two independent general-purpose amplifiers in one compact package (對比LM324KAPWR)
- Manufacturer positioning for automotive and industrial control systems (對比LM2904QDR)
- SOIC-8 dual-amplifier footprint shared across established LM2904 cross-references (對比LM2904D)
設計說明
Place the local bypass capacitor beside the LM2904WHYDT supply connection and provide a short, low-impedance ground return. Select the capacitor and any additional bulk capacitance according to the manufacturer recommendations and the impedance of the upstream supply. Avoid long input and feedback runs, since supply ripple and ground displacement can appear as input-referred error in high-gain analog stages.
Assign one amplifier channel to the most sensitive signal path and keep both channels' feedback loops compact. Route noninverting inputs away from supply, clock, and switching-node copper. If both amplifiers process related signals, maintain symmetrical grounding and avoid routing one channel’s output near the other channel’s input. This reduces channel-to-channel coupling and makes troubleshooting easier.
Do not assume that every device labeled LM2904 is an electrical drop-in replacement. Verify the exact pin assignment, supply range, input common-mode range, output swing, offset voltage, bias current, bandwidth, load stability, and temperature grade. An SOIC-8 footprint alone does not prove equivalent behavior, especially for high-impedance sensors, single-supply operation near ground, or automotive temperature requirements.
For low-frequency filter or amplifier stages, check closed-loop gain against the device gain-bandwidth product and confirm stability with the actual source and load capacitance. Add a small isolation resistor between the amplifier and unusually capacitive loads only after reviewing the manufacturer stability guidance. This is particularly important when driving long cable, sensor, or actuator connections from a general-purpose op amp.
合規資訊
The device is described by STMicroelectronics for automotive and industrial control systems, but grade-specific qualification and environmental declarations must be confirmed in the current manufacturer documentation. The supplied catalog information does not explicitly state RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status.