LM2904YDT - 30V Low-Power Dual Op Amp | STMicroelectronics
MPN: LM2904YDT ✓ 啟用中LM2904YDT 概覽
An operational amplifier, or op amp, is a voltage-gain device used to amplify small input signals in analog signal chains. The LM2904 family belongs to the broader hierarchy of analog integrated circuits, signal amplifiers, operational amplifiers, and general-purpose amplifiers. Its differential inputs and single-ended outputs allow each channel to support common tasks such as buffering, gain amplification, voltage comparison, filtering, and instrumentation-style signal conditioning.
The LM2904YDT provides two amplifier circuits in one 8-SOIC package. Its stated 30 V family rating supports operation from single-supply industrial signal-conditioning circuits, while the low-power architecture suits battery-powered and portable equipment. The 0.6 V/µs slew rate provides a concrete indication of how quickly the output can follow a changing input, making the device appropriate for low-to-moderate-bandwidth applications rather than high-speed signal paths.
STMicroelectronics describes the LM2904 family as a low-power dual operational amplifier. The automotive-oriented Y suffix and automotive-grade classification make the LM2904YDT relevant to vehicle electronics, industrial controls, and other systems that require a dual amplifier in a compact surface-mount package. Because the package contains two channels, PCB area and component count can be reduced compared with separate single-channel amplifiers.
Typical uses include low-frequency sensor conditioning, current-loop signal amplification, audio preamplification, active filtering, voltage buffering, and general industrial control. The device is also suitable for split-supply circuits when the signal can remain within the input and output common-mode limits specified by the manufacturer datasheet. Applications requiring wide bandwidth, rail-to-rail input or output operation, very low offset voltage, or low-noise performance should compare the LM2904YDT with precision or rail-to-rail amplifier families before finalizing the design.
Designers should verify input common-mode range, output swing, output-current capability, and stability with the external compensation network for each specific operating point. Keep input and feedback traces short, place decoupling capacitors close to the supply pins, and avoid using the amplifier outside its stated supply and common-mode limits. A bypass capacitor near each device helps control supply-line noise on shared analog boards.
This product page combines the LM2904YDT operating identity with package, application, drop-in replacement, and design guidance. It highlights where the conventional low-power dual op amp is appropriate and where precision, speed, or rail-to-rail characteristics may justify a different amplifier architecture.
直接替換替代品,適用於 LM2904YDT — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: LM2904YDT (相同外形與佔位) — 差異在於 Package, Gain-Bandwidth Product, Slew Rate, Amplifier Type, Supply Voltage Range.
LM2904YD
✅ 直接替換📋 參考替代品(不在目錄中)
LM2904WPT
✅ 直接替換聯絡詢價
查看資料表 →LM2904DR
✅ 直接替換聯絡詢價
查看資料表 →LM2904VDR2G
✅ 直接替換聯絡詢價
查看資料表 →LM2904YDT 最大額定值與電氣特性
| Amplifier Type | General-purpose operational amplifier |
| Number of Channels | 2 channels |
| Number of Circuits | 2 circuits |
| Architecture | Dual independent operational amplifier |
| Power Class | Low-power |
| Family Supply Voltage Rating | 30 V |
| Slew Rate | 0.6 V/µs |
| 輸出類型 | Single-ended |
| 封裝 | 8-SOIC |
| 安裝類型 | Surface mount |
| Automotive Grade | Automotive-grade variant |
| RoHS 狀態 | Compliant |
| REACH Status | Compliant |
| Moisture Sensitivity Level | MSL 1 |
LM2904YDT 8-soic 腳位配置指南
LM2904YDT(8-soic 封裝)的腳位配置。 此類比元件具有輸入、輸出與電源腳位。偏移歸零、補償與致能腳位配置請參閱製造商資料表。適用於訊號調理與放大器電路。
無詳細腳位定義資料: LM2904YDT.
請參閱 資料表 以查看完整腳位配置。
典型應用
LM2904YDT 適用於 6 應用s: Industrial Sensor Signal Conditioning, Automotive Low-Frequency Control Circuits, Battery-Powered Monitoring Equipment, Audio Preamplification and Buffering, Active Filtering and Analog Control, Power-Supply Feedback and Load Buffering.
Industrial Sensor Signal Conditioning
The LM2904YDT fits industrial sensor-conditioning stages that need two amplifier channels and a conventional 8-SOIC footprint. Each amplifier can provide gain or buffering around a transducer signal, while the device’s 30 V family rating and low-power characterization suit control boards operating from industrial supply rails. The 0.6 V/µs slew rate is adequate for many low-bandwidth pressure, temperature, and position signals, but the design must stay within the manufacturer’s input common-mode and output-swing limits. Decoupling capacitors should be placed close to the supply pins, and feedback components should use stable resistors and capacitors to avoid unexpected gain or oscillation.
推薦
Automotive Low-Frequency Control Circuits
The automotive-grade designation makes the LM2904YDT a candidate for low-frequency vehicle control and signal-conditioning circuits that operate within its documented electrical limits. Two channels can support separate interface or conditioning paths, reducing the component count compared with two discrete single amplifiers. The 30 V family rating and 0.6 V/µs slew rate can suit slowly changing control signals rather than high-bandwidth communication channels. Designers must still verify temperature range, common-mode behavior, output swing, load drive, electromagnetic compatibility, and qualification requirements. A solid ground return, short feedback paths, and local supply bypassing are especially important in vehicle electrical environments.
推薦
Battery-Powered Monitoring Equipment
The low-power dual-amplifier architecture of the LM2904YDT suits portable monitoring equipment in which two low-bandwidth analog channels must be conditioned from limited power budgets. The two amplifiers can handle sensor amplification, voltage buffering, or active filtering without requiring two separate packages. Its 0.6 V/µs slew rate is suitable for many slowly varying sensor outputs, while the dual integration can reduce board area. Battery designs should still calculate worst-case supply current, verify the operating voltage against the manufacturer’s electrical limits, and account for the output drive required by the ADC input and external network. Low-leakage components may be necessary when the source impedance is high.
推薦
Audio Preamplification and Buffering
The LM2904YDT can be used for modest-bandwidth audio preamplification or impedance buffering where two signal paths share a common 8-SOIC package. The 0.6 V/µs slew rate is adequate for many line-level audio stages operating well below high-frequency communication rates. The design must ensure that the input signal remains inside the amplifier’s common-mode range and that the output swing accommodates the chosen gain. For microphone or high-impedance sources, input bias current and source impedance can materially affect DC accuracy. The LM2904YDT should not be treated as a low-noise precision device, so headphone outputs, audio ADCs, or high-gain microphone stages may require a dedicated low-noise amplifier.
推薦
Active Filtering and Analog Control
The two channels in the LM2904YDT can implement active filters, integrators, or analog control functions where moderate frequency and precision requirements are sufficient. Its 0.6 V/µs slew rate constrains large-signal performance through high-Q or narrow-band networks, so the gain and capacitor values must be checked for stability. An 8-SOIC package also permits the two amplifier sections to be placed close to associated passive components, reducing sensitive routing. For precision filters, the amplifier’s offset and bias-current behavior contribute directly to output error. Use low-tolerance resistors and suitable film or ceramic capacitors, observe the manufacturer’s grounding guidance, and probe the final circuit because amplifier and component parasitics can shift the nominal response.
推薦
Power-Supply Feedback and Load Buffering
The LM2904YDT can buffer a power-supply feedback node or monitor a low-frequency voltage signal with one channel while the second channel handles another supervisory function. Its 30 V family rating is useful when the surrounding circuit operates above ordinary low-voltage logic levels, and the 0.6 V/µs slew rate is adequate for many feedback and supervisory signals. The amplifier still requires suitable input and output headroom, so its output cannot be assumed to reach either supply rail. Place the device near the feedback components, minimize the feedback-loop trace, and use local decoupling to prevent supply ripple from appearing as output noise. The exact load and stability network must be evaluated at the intended operating voltage.
推薦
推薦產品摘要
工程參考資料,適用於 LM2904YDT — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | LM2904YD | LM2904WPT | LM2904 | LM2904VDR2G |
|---|---|---|---|---|---|
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics | Texas Instruments | onsemi |
| Package | SOIC-8 | SOIC-8 | SOIC-8 | SOIC-8 | SOIC-8 |
| Amplifier Channels | 2 channels | 2 channels | 2 channels | 2 channels | 2 channels |
| Supply-Voltage Family Rating | 30 V | 30 V | 30 V | 26 V | 30 V |
| Product Classification | General-purpose low-power dual operational amplifier | General-purpose low-power dual operational amplifier | General-purpose low-power dual operational amplifier | Dual general-purpose operational amplifier | General-purpose dual operational amplifier |
主要差異化特點
- Automotive-grade ordering option in a dual 8-SOIC package (對比LM2904VDR2G)
- Higher family voltage rating than the TI LM2904 (對比LM2904)
- Two general-purpose channels in one compact package (對比LM324ADR)
設計說明
Do not interpret the 30 V family rating as permission to operate the output or input at every point between the supply rails. Check the manufacturer’s input common-mode range, output swing, supply limits, and temperature conditions for the selected grade. In particular, a 5 V or 12 V single-supply circuit may not accept a 0 V input, and the output may require additional headroom. This is especially important when replacing a rail-to-rail amplifier in an existing design.
Place the supply bypass capacitor directly between the supply and ground pins of the LM2904YDT, with the ground connection returning to the quiet analog ground region. Keep input, feedback, and output traces short, and avoid routing sensitive signal lines beside high-current switching nodes. Because the 8-SOIC package contains two amplifier channels, arrange the footprints so that external feedback networks and decoupling paths can be connected without long loops around the package.
Check large-signal behavior against the stated 0.6 V/µs slew rate before selecting gain and operating frequency. A high closed-loop gain increases the effective slew-rate demand and can cause output distortion or instability. Use stable feedback resistors, verify whether the application requires an external compensation capacitor, and evaluate the complete circuit with the intended load and bypass network. The dual channels should also be isolated enough to prevent one channel’s output current from disturbing the other channel’s source impedance.
Calculate worst-case supply power using both channels, the load current, and the amplifier’s quiescent current under the intended operating mode. The device is low power, but two active channels and sustained output loading can still contribute meaningful consumption in battery-powered equipment. Confirm the quiescent current and output-current limits from the manufacturer datasheet, then verify that the regulator can meet the transient demand without producing feedback that disturbs the amplifier’s supply rail.
合規資訊
RoHS and REACH compliance are identified for the LM2904YDT. Exact AEC-Q100 qualification, lead-free status, halogen-free status, and conflict-minerals status require confirmation from the manufacturer.