LPC2131FBD64 - 60MHz ARM7 MCU, 32KB Flash | NXP
MPN: LPC2131FBD64 ✗ 停產LPC2131FBD64 概覽
An ARM7TDMI-S microcontroller is a 32-bit RISC device that combines a conventional processor core, embedded program memory, and dedicated peripherals in one integrated circuit. Its position in the product hierarchy is microcontroller, then 32-bit RISC microcontroller, then ARM7TDMI-S embedded controller. The architecture supports 32-bit code execution while retaining deterministic interrupt-driven operation for real-time control workloads.
Principal features include a 60 MHz maximum clock, 32 KB of embedded high-speed flash, 8 KB of SRAM, a 10-bit ADC, an on-chip DAC, PWM outputs, and multiple GPIO. The 128-bit memory interface and accelerator architecture improve instruction throughput. In-System Programming and In-Application Programming support add manufacturing and field-update flexibility without removing the microcontroller from its target circuit.
The LPC2131/32/34/36/38 family uses a common hardware platform across several flash configurations. The 32 KB version has lower on-chip memory than the 64, 128, 256, and 512 KB family members, but retains the same 60 MHz ARM7TDMI-S core and 64-pin LQFP footprint. This makes the LPC2131FBD64 appropriate for compact code where external memory would otherwise increase cost and board area.
Typical applications include industrial data loggers, serial protocol converters, motor and process controllers, test equipment, and communications gateways. Its mixed-signal peripherals allow an analog sensor interface and digital control logic to share one device, while PWM and capture functions support actuator monitoring and timing tasks.
When designing around the LPC2131FBD64, check every peripheral pin against the selected board variant and provide the decoupling and oscillator arrangements shown in the manufacturer datasheet. Because this is an established ARM7 design, confirm that current toolchain, library, and driver support covers the exact firmware and production requirements before committing to a new design.
This page consolidates core specifications, ordering variants, comparison data, and practical design guidance. It also documents where package-level verification and datasheet pin descriptions should be used, helping engineers evaluate the LPC2131FBD64 without relying on generic microcontroller recommendations.
直接替換替代品,適用於 LPC2131FBD64 — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: LPC2131FBD64 (相同外形與佔位) — 差異在於 ADC Resolution, Package, Product Type, Supply Voltage.
LPC2131FBD64/01
✅ 直接替換聯絡詢價
查看資料表 →LPC2131FBD64/01,15
✅ 直接替換📋 參考替代品(不在目錄中)
LPC2131FBD64/01,11
✅ 直接替換📋 參考替代品(不在目錄中)
LPC2131FBD64/01S
✅ 直接替換📋 參考替代品(不在目錄中)
LPC2131FBD64 最大額定值與電氣特性
| Product Type | 16/32-bit ARM7TDMI-S RISC microcontroller |
| Maximum CPU Clock | 60 MHz |
| Embedded Flash Memory | 32 KB |
| Flash Organization | 32K x 8 bits |
| SRAM | 8 KB |
| ADC Resolution | 10 bits |
| DAC | Integrated |
| 供應電壓 | 3.3 V |
| Processor Core | ARM7TDMI-S |
| Memory Interface | 128 bits wide |
| Program Memory | 32 KB embedded high-speed flash |
| Programming Support | ISP and IAP |
| 封裝 | 64-pin LQFP, 10 x 10 mm |
| 安裝類型 | Surface mount |
| RoHS 狀態 | unknown |
| REACH Status | unknown |
LPC2131FBD64 64-pin lqfp, 10 x 10 mm 腳位配置指南
LPC2131FBD64(64-pin lqfp, 10 x 10 mm 封裝)的腳位配置。 此數位 IC 包含 GPIO、通訊介面(UART、SPI、I2C)與電源腳位。替代腳位功能與配置選項請參閱製造商資料表。對嵌入式系統設計與 PCB 佈局至關重要。
無詳細腳位定義資料: LPC2131FBD64.
請參閱 資料表 以查看完整腳位配置。
典型應用
LPC2131FBD64 適用於 6 應用s: Industrial Data Acquisition Controller, Serial Protocol Converter, Motor and Process Control, Communications Gateway Module, Embedded Test and Measurement, Legacy ARM7 Equipment Upgrade.
Industrial Data Acquisition Controller
The LPC2131FBD64 fits compact data-acquisition and condition-monitoring equipment because its 60 MHz ARM7TDMI-S core can service interrupt-driven sampling while the integrated 10-bit ADC handles analog sensor inputs. Its 32 KB flash and 8 KB of SRAM are sufficient for compact buffering, calibration tables, and communication routines. Use the PWM outputs for excitation or reference timing, and verify the analog pin multiplexing against the NXP datasheet before final routing.
推薦
Serial Protocol Converter
The LPC2131FBD64 can serve as a protocol-conversion gateway between legacy serial equipment and a host controller. The ARM7TDMI-S core executes at 60 MHz, allowing the firmware to handle framing, checksums, buffering, and real-time event scheduling, while the 32 KB flash footprint stores fixed protocol tables and 8 KB of SRAM supports short frame buffering. Its integrated ADC and DAC are optional if the converter also performs analog monitoring.
推薦
Motor and Process Control
The LPC2131FBD64 is appropriate for small motor controllers and industrial process-control modules where deterministic timing, mixed-signal I/O, and compact firmware are priorities. Its 60 MHz core supports rapid control-loop execution, the PWM channels can generate actuator commands, and the 10-bit ADC supports feedback measurement. Keep the analog reference, power routing, and PWM outputs within the electrical conditions defined in the manufacturer datasheet.
推薦
Communications Gateway Module
The LPC2131FBD64 can form the control core of a small communications gateway that supervises UART, SPI, and other embedded interfaces. Its 128-bit memory interface and accelerator architecture support efficient 32-bit instruction execution at the 60 MHz clock, while ISP and IAP simplify production programming and controlled firmware updates. The 32 KB flash budget is suitable for lightweight protocol stacks, not large TCP or TLS implementations.
推薦
Embedded Test and Measurement
The LPC2131FBD64 is useful in legacy-compatible test equipment where stimulus generation, timing, and data capture must share one microcontroller. Its PWM blocks, ADC, DAC, GPIO, and 60 MHz processing core support measurement sequencing and response generation within a single controller. The 8 KB of SRAM limits long waveform capture, so use external storage when records exceed the device’s local buffering capacity.
推薦
Legacy ARM7 Equipment Upgrade
The LPC2131FBD64 is appropriate for maintaining or selectively upgrading established ARM7TDMI-S equipment without introducing a new processor architecture or board form factor. The familiar 64-LQFP footprint, 60 MHz clock, and 32 KB flash organization allow an existing design to retain much of its software and hardware structure. Confirm pin multiplexing, peripheral assignments, and application-code compatibility before treating the upgrade as a component substitution.
推薦
推薦產品摘要
工程參考資料,適用於 LPC2131FBD64 — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | LPC2131FBD64/01 | LPC2131FBD64/01,15 | LPC2131FBD64/01,11 | LPC2131FBD64/01S |
|---|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | 64-LQFP (10 x 10 mm) | 64-LQFP (10 x 10 mm) - same | 64-LQFP (10 x 10 mm) - same | 64-LQFP (10 x 10 mm) - same | 64-LQFP (10 x 10 mm) - same |
| Processor Core | ARM7TDMI-S | ARM7TDMI-S | ARM7TDMI-S | ARM7TDMI-S | ARM7TDMI-S |
| Maximum CPU Clock | 60 MHz | 60 MHz | 60 MHz | 60 MHz | 60 MHz |
| Embedded Flash Memory | 32 KB | 32 KB | 32 KB | 32 KB | 32 KB |
| SRAM | 8 KB | 8 KB | 8 KB | 8 KB | 8 KB |
| ADC Resolution | 10 bits | 10 bits | 10 bits | 10 bits | 10 bits |
| Programming Support | ISP and IAP | ISP and IAP | ISP and IAP | ISP and IAP | ISP and IAP |
| Supply Voltage | 3.3 V | 3.3 V | 3.3 V | 3.3 V | 3.3 V |
主要差異化特點
- Identical core and memory organization across documented ordering variants (對比LPC2131FBD64/01,15)
- Mixed-signal integration reduces external component count (對比LPC2131FBD64/01,11)
- Field-update capability within a constrained embedded footprint (對比LPC2131FBD64/01S)
設計說明
Route the 64-pin LQFP footprint in accordance with the NXP package drawing, including correct pad length, pitch, and exposed thermal considerations where applicable. Keep the 3.3 V supply pins and decoupling capacitors close to their assigned pins, and preserve the datasheet-recommended return path. Verify every multiplexed GPIO, ADC, DAC, PWM, and debug signal against the selected pin-connectivity table before releasing artwork.
Calculate the digital and analog load before fixing power capacity, then follow the manufacturer’s recommended supply voltage and decoupling arrangement. The ADC and DAC may require filtered analog references and separate routing to reduce coupling from switching nodes. For mixed-signal boards, partition analog and digital return paths carefully and avoid routing PWM edges beneath sensitive analog inputs.
Do not treat a 64-lead Cortex-M device as a pin-compatible substitute for this ARM7TDMI-S part. Confirm the complete pin-connectivity table, startup sequence, peripheral register map, and application code against the NXP family datasheet. Also verify that 32 KB of flash and 8 KB of SRAM are sufficient after linker-map analysis, including space reserved for bootloader, interrupt vectors, and IAP code.
Use the fastest available debug and serial programming interface only after confirming its pin multiplexing and signal-integrity requirements. Avoid long unterminated traces from the microcontroller to external connectors, especially on lines shared with ADC inputs. For PWM-driven loads, keep switching-current paths compact and provide local bulk decoupling so control-loop timing is not disturbed by supply transients.
合規資訊
Compliance attributes are not stated in the product documentation pages for this legacy device. Request current RoHS, REACH, and material-declaration documentation through the Request a Quote form on this page.