MAX211EEWI+ - 15kV ESD 4/5 RS-232 Transceiver | Maxim
MPN: MAX211EEWI+ ✓ 啟用中MAX211EEWI+ 概覽
An RS-232 transceiver is an interface IC that converts logic-level signals to and from RS-232 line levels. It belongs to the transceiver class, interface IC hierarchy, and broader semiconductor category. The MAX211EEWI+ combines four driver channels with five receiver channels, allowing multiple serial ports or asymmetric communication paths to share one package while providing a standardized physical interface for data transmission.
Key features include 15kV ESD protection, TTL-compatible tri-state driver operation, and operation from a 4.5V to 5.5V supply. The integrated charge pump eliminates the need for a separate external charge-pump supply arrangement for standard single-supply RS-232 operation. Its four-driver and five-receiver organization also provides receiver headroom when a system requires more receive channels than transmit channels.
The E suffix identifies the electrically enhanced device family, while the wider temperature capability associated with the EWI+ ordering code is -40°C to +85°C. The MAX211 family is also offered in 28-pin wide SO and SSOP configurations, but the target ordering code uses the 28-pin wide SOIC package. Exact propagation delay, slew rate, receiver thresholds, and input capacitance should be confirmed against the manufacturer datasheet before finalizing a high-speed interface design.
Typical uses include industrial serial-port equipment, data acquisition systems, instrumentation, control panels, and embedded systems that connect TTL or CMOS logic to RS-232 equipment. The five-receiver, four-driver arrangement is particularly useful where more input channels are required than output channels. Integrating the charge pump also reduces external circuitry and simplifies single-rail implementation compared with charge-pump-free or externally assisted alternatives.
Designers should verify signal-level compatibility, grounding, connector selection, and cable length for the selected RS-232 standard. ESD protection is valuable at the connector interface, but external protection may still be needed for severe industrial surge environments. Keep ground and signal routing controlled, place the charge-pump capacitors close to their specified pins, and avoid using TTL outputs without first confirming the required driver-enable and tri-state behavior.
This page combines the Maxim family specifications, verified distributor listings, pin-compatible family alternatives, and application-focused engineering guidance to support component selection and PCB design planning.
直接替換替代品,適用於 MAX211EEWI+ — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: MAX211EEWI+ (相同外形與佔位) — 差異在於 Package, Receiver Count, Driver Count, Supply Voltage.
MAX211ECWI+
✅ 直接替換聯絡詢價
查看資料表 →MAX211EWI+
✅ 直接替換聯絡詢價
查看資料表 →MAX213EEWI
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
MAX241EEWI
✅ 直接替換📋 參考替代品(不在目錄中)
MAX211EEWI+ 規格
| Transceiver Configuration | 4 drivers / 5 receivers |
| Interface Standard | RS-232 |
| Supply Voltage Range | 4.5V to 5.5V |
| Nominal Supply Voltage | +5V |
| Driver Count | 4 channels |
| Receiver Count | 5 channels |
| ESD Protection | ±15kV |
| Charge Pump | Integrated |
| Driver Output Type | TTL tri-state |
| 封裝 | 28-pin WSOIC |
| Package Family | Wide small-outline IC |
| 安裝類型 | Surface mount |
| Minimum Operating Temperature | -40°C |
| Maximum Operating Temperature | +85°C |
| Operating Supply Range | 4.5V to 5.5V |
MAX211EEWI+ wide small-outline ic 腳位配置指南
MAX211EEWI+(wide small-outline ic 封裝)的腳位配置。 腳位編號、功能與連接圖定義於製造商資料手冊中。請參閱該手冊以取得確切的封裝尺寸與焊接指引。
無詳細腳位定義資料: MAX211EEWI+.
請參閱 資料表 以查看完整腳位配置。
典型應用
MAX211EEWI+ 適用於 6 應用s: Industrial RS-232 Data Acquisition, Instrumentation and Test Equipment, Embedded Serial Communication Controller, Serial Control Panel, Point-of-Sale and Peripheral Interface, Industrial Communication Gateway.
Industrial RS-232 Data Acquisition
The MAX211EEWI+ fits industrial data-acquisition equipment that must translate between TTL or CMOS controller logic and RS-232 instruments. Its 4.5V to 5.5V operating range supports conventional 5V systems, while the integrated charge pump simplifies single-rail implementation. Four driver and five receiver channels provide asymmetric connectivity for controlling one or more peripherals and collecting status data. The -40°C to +85°C rating is useful in factory environments, and ±15kV ESD protection improves interface resilience, although connector-level surge protection may still be required.
推薦
Instrumentation and Test Equipment
The MAX211EEWI+ is appropriate for laboratory and field instrumentation that uses legacy RS-232 links for control, logging, or service access. Four driver outputs can connect multiple enabled receivers, while five receiver channels support multiple incoming data sources. Its integrated charge pump reduces the number of external support components compared with designs that provide a separate boosted supply. The wide-SOIC package remains compatible with conventional through-hole-style PCB assembly practices, and the -40°C to +85°C range supports temperature-controlled industrial test systems.
推薦
Embedded Serial Communication Controller
The MAX211EEWI+ can serve as the physical-layer complement to an embedded UART or microprocessor in systems that still require RS-232 connectivity. The four-driver and five-receiver organization allows several serial links to share one interface IC, reducing board area relative to separate single-channel transceivers. TTL tri-state outputs support shared-bus arrangements when the host firmware controls driver enable timing correctly. Single-supply operation from 4.5V to 5.5V and integrated charge-pump circuitry simplify connections to 5V embedded systems, though modern designs often prefer USB or differential interfaces when the physical standard permits.
推薦
Serial Control Panel
A MAX211EEWI+ is useful in a human-machine-interface control panel that must retain a wired RS-232 command port. The five receiver channels can accept data from multiple panel modules, while four driver channels support communication with up to four enabled receiving nodes. The integrated charge pump allows operation from one 5V rail, making the device suitable for space-constrained electronics with limited power distribution. ESD protection is valuable around touchable or externally accessible equipment, but the final design should still use a suitable connector, chassis grounding, and protection network for its installation environment.
推薦
Point-of-Sale and Peripheral Interface
The MAX211EEWI+ can bridge a controller to RS-232 peripherals such as scanners, printers, or service terminals in legacy point-of-sale equipment. Four driver channels accommodate several enabled peripheral inputs, and five receiver channels can collect acknowledgements or status signals. The 4.5V to 5.5V supply range aligns with many embedded 5V systems, while the integrated charge pump avoids a separate negative-voltage generation circuit. Because exposed RS-232 ports are susceptible to both ESD and larger surge transients, the board design should combine the device's internal protection with appropriately rated external protection and robust signal grounding.
推薦
Industrial Communication Gateway
The MAX211EEWI+ is suitable for a communication gateway that bridges a legacy RS-232 device to a modern embedded controller. Its four drivers and five receivers support several physical channels while preserving a compact 28-pin wide-SOIC footprint. The integrated charge pump permits straightforward 5V-only implementation, and the -40°C to +85°C rating supports deployment in unheated industrial enclosures. Signal-integrity planning should account for unequal driver and receiver counts, the tri-state control state of unused outputs, and the potential for ground-potential differences between equipment connected through long RS-232 cables.
推薦
推薦產品摘要
工程參考資料,適用於 MAX211EEWI+ — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | MAX211ECWI+ | MAX211EWI | MAX213EEWI | MAX241EEWI |
|---|---|---|---|---|---|
| Brand | Maxim Integrated | Maxim Integrated | Maxim Integrated | Maxim Integrated | Maxim Integrated |
| Package | 28-SOIC | 28-SOIC - same | 28-SOIC - same | 28-SOIC - same | 28-SOIC - same |
主要差異化特點
- Broader industrial temperature coverage (對比MAX211ECWI+)
- Four-driver and five-receiver configuration (對比MAX241EEWI)
- Single 5V rail with integrated charge pump (對比MAX213EEWI)
設計說明
Place the charge-pump capacitors and the required input and output bypass capacitors directly beside their associated pins. Keep the charge-pump loop compact because long PCB traces can increase radiated noise and reduce margin on the RS-232 driver outputs. Use the manufacturer's recommended capacitance and ESR values, and route connector-side protection components close to the external pins rather than back toward the transceiver.
Do not enable multiple driver outputs onto the same RS-232 node unless the system intentionally supports that connection and the outputs are designed for it. TTL tri-state control must leave unused drivers in a high-impedance state. Confirm the receiver enable or shutdown polarity in the manufacturer pin table because a wrong control-state interpretation can prevent communication or create excessive bus contention.
The ±15kV ESD rating is not equivalent to unlimited surge withstand. For cables leaving an enclosure, combine the internal protection with connector placement, chassis or signal-ground strategy, and external surge protection appropriate to the installation. Keep long RS-232 traces away from clocks, switching inductors, and high-current return paths to reduce common-mode noise and false receive transitions.
Use a solid low-impedance ground plane for the transceiver and provide an unobstructed return path beneath or near the interface traces. Avoid splitting the ground plane beneath the wide-SOIC footprint, and avoid routing high-speed digital signals directly beneath charge-pump nodes. Maintain practical separation between outgoing and incoming RS-232 channels when their ground references or cable routes differ.
合規資訊
No specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status was identified for the target ordering code. The manufacturer family is described as operating in harsh environments, but this does not establish a formal compliance qualification.