MAX3232IPWRG4 - 3-5.5V RS-232 Transceiver | Texas Instruments
MPN: MAX3232IPWRG4 ✓ 啟用中MAX3232IPWRG4 概覽
An RS-232 transceiver is a semiconductor interface that converts logic-level signals into RS-232 line levels and converts received line-level signals back into CMOS logic. The MAX3232 belongs to the interface IC and RS-232 transceiver hierarchy, using an on-chip dual charge-pump circuit to generate the positive and negative voltages required by true RS-232 operation. This makes it suitable for industrial control, instrumentation, point-of-sale equipment, and legacy serial-port systems.
Key features include a 3 V to 5.5 V supply range, full-duplex operation with two drivers and two receivers, and data rates up to 250 kbps according to the manufacturer product information. The device also provides ±15-kV ESD protection on the serial-port connection terminals and uses external 0.1 µF charge-pump capacitors. Its low-voltage operation reduces the power burden compared with traditional ±5 V or ±12 V RS-232 implementations.
The internal charge-pump circuitry generates the bipolar voltages required to meet TIA/EIA-232-F electrical requirements. Because the charge pump switches internally, PCB layout must keep the charge-pump capacitors close to their designated pins and preserve adequate routing away from sensitive analog or communication circuits. The receiver includes hysteresis, which helps reject noise and prevents excessive output chatter as an input signal crosses the logic threshold.
Typical applications include legacy RS-232 ports on industrial controllers, test and measurement equipment, programmable logic controllers, security systems, and computer peripherals. The part is particularly useful where a modern 3.3 V or 5 V controller must communicate with an RS-232 device through a DB9 or equivalent connector.
The principal design trade-off is that the MAX3232IPWRG4 is a mature RS-232 interface rather than a modern USB-to-serial bridge. It requires external charge-pump capacitors, a suitable connector, and careful treatment of the exposed cable-side pins. Its industrial temperature grade supports equipment intended for a wider operating environment than commercial-temperature parts.
This product record combines manufacturer specifications, exact package information, lifecycle status, source links, and verified substitute information to support component selection. Engineers can use the comparison table and replacement notes to determine whether an alternative preserves the TSSOP-16 footprint, supply range, channel count, and RS-232 operating characteristics.
直接替換替代品,適用於 MAX3232IPWRG4 — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: MAX3232IPWRG4 (相同外形與佔位) — 差異在於 Package, Supply Voltage Range, ESD Protection, Maximum Data Rate, Product Type.
MAX3232IPWR
✅ 直接替換聯絡詢價
查看資料表 →MAX3232EIPWG4
✅ 直接替換聯絡詢價
查看資料表 →MAX3232EIPWG4
✅ 直接替換 ⚠️ 規格未經驗證聯絡詢價
查看資料表 →MAX3232CPWR
✅ 直接替換聯絡詢價
查看資料表 →MAX3232CPWG4
✅ 直接替換聯絡詢價
查看資料表 →SP3232EBEY-L/TR
✅ 直接替換聯絡詢價
查看資料表 →MAX3232IPWRG4 規格
| Device Type | RS-232 line transceiver |
| Number of Drivers | 2 |
| Number of Receivers | 2 |
| Duplex Type | Full duplex |
| Supply Voltage Range | 3 V to 5.5 V |
| Maximum Data Rate | 250 kbps |
| ESD Protection | ±15 kV terminal to terminal |
| Interface Standard | TIA/EIA-232-F |
| Charge-Pump Architecture | Dual charge-pump circuit |
| External Charge-Pump Capacitors | 0.1 µF each |
| Receiver Hysteresis | 300 mV |
| 封裝 | 16-pin TSSOP |
| Terminal Count | 16 |
| 安裝類型 | Surface mount |
| 工作溫度範圍 | -40 °C to +85 °C |
MAX3232IPWRG4 16-pin tssop 腳位配置指南
MAX3232IPWRG4(16-pin tssop 封裝)的腳位配置。 腳位編號、功能與連接圖定義於製造商資料手冊中。請參閱該手冊以取得確切的封裝尺寸與焊接指引。
無詳細腳位定義資料: MAX3232IPWRG4.
請參閱 資料表 以查看完整腳位配置。
典型應用
MAX3232IPWRG4 適用於 6 應用s: Industrial RS-232 Controller Interface, Programmable Logic Controller Communication, Test and Measurement Equipment, Point-of-Sale and Peripheral Communication, Security and Access-Control Equipment, Embedded Service and Debug Port.
Industrial RS-232 Controller Interface
The MAX3232IPWRG4 fits industrial controllers that retain RS-232 communication with drives, meters, or service equipment. Its 3- to 5.5-V supply range allows connection to 3.3 V or 5 V controller logic without separate ±12 V interface rails. The dual charge-pump generates compliant positive and negative line voltages, while the two transmitters and two receivers support full-duplex links. Its -40 °C to +85 °C operating range supports industrial enclosures, although connector ratings and system-level thermal rise must also be checked.
推薦
Programmable Logic Controller Communication
The MAX3232IPWRG4 is suitable for PLC communication modules that must translate controller logic into RS-232 signals. A maximum data rate of 250 kbps supports common asynchronous serial configurations, while the full-duplex arrangement permits simultaneous command transmission and status reception. Its single 3- to 5.5-V supply simplifies interface design around modern embedded processors. The four required 0.1 µF capacitors should be placed directly beside their charge-pump pins to reduce switching-loop area and cable-side noise.
推薦
Test and Measurement Equipment
The MAX3232IPWRG4 can provide a legacy RS-232 port on bench instruments, programmable power supplies, and automated test systems. The 3.3 V compatibility reduces the need for level shifting between the transceiver and modern control logic, while the integrated charge pump supplies the bipolar voltages required by RS-232. The device supports up to 250 kbps, allowing it to match conventional serial-control links. For laboratory equipment, use a suitable isolated or chassis-connected protection strategy at the external connector and verify grounding to avoid introducing noise into measurements.
推薦
Point-of-Sale and Peripheral Communication
The MAX3232IPWRG4 supports RS-232 links used by point-of-sale terminals, scales, printers, and other commercial peripherals. The two-transmitter, two-receiver configuration allows independent inbound and outbound channels, and the device operates from the 5 V rails commonly present in peripheral equipment. Its 250-kbps maximum rate is more than adequate for many short-distance transaction and configuration links. Cable length, connector grounding, and peripheral-specific protocol requirements should be validated together because the transceiver rating does not remove all RS-232 cable limitations.
推薦
Security and Access-Control Equipment
The MAX3232IPWRG4 can be used in access-control panels and security-system modules that maintain an RS-232 service or configuration port. Its low-voltage operation integrates cleanly with 3.3 V or 5 V system logic, and ±15-kV terminal-to-terminal ESD protection adds useful robustness at an exposed cable-side interface. The industrial temperature range is advantageous in equipment stored in unconditioned spaces. The design should still include connector grounding, surge protection appropriate to the installation, and verified separation between the protected cable interface and sensitive security circuitry.
推薦
Embedded Service and Debug Port
The MAX3232IPWRG4 is appropriate for embedded systems that expose an RS-232 configuration, firmware-update, or diagnostic port. It bridges low-voltage CMOS UART signals to true RS-232 levels without requiring the host system to generate bipolar voltages. The dual full-dupplex channels support common transmit-and-receive diagnostic workflows, and 250 kbps is suitable for many bootloaders and console protocols. Firmware should implement appropriate electrical safeguards because the RS-232 transceiver provides logical signaling but does not by itself establish a secure authenticated update channel.
推薦
推薦產品摘要
工程參考資料,適用於 MAX3232IPWRG4 — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | MAX3232IPWR | MAX3232EIPW | MAX3232EIPWG4 | MAX3232CPW | MAX3232CPWG4 | SP3232EBEY-L |
|---|---|---|---|---|---|---|---|
| Package | 16-pin TSSOP | 16-pin TSSOP | 16-pin TSSOP | 16-pin TSSOP | 16-pin TSSOP | 16-pin TSSOP | 16-pin SSOP |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Lattice Semiconductor |
| Device Type | Dual RS-232 transceiver | Dual RS-232 transceiver | Dual RS-232 transceiver | Dual RS-232 transceiver | Dual RS-232 transceiver | Dual RS-232 transceiver | RS-232 transceiver |
| Supply Voltage | 3 V to 5.5 V | 3 V to 5.5 V | 3 V to 5.5 V | 3 V to 5.5 V | 3 V to 5.5 V | 3 V to 5.5 V | Supports 3.3 V operation |
| Transmitters and Receivers | 2 drivers and 2 receivers | 2 drivers and 2 receivers | 2 drivers and 2 receivers | 2 drivers and 2 receivers | 2 drivers and 2 receivers | 2 drivers and 2 receivers | Dual RS-232 transceiver |
主要差異化特點
- Industrial-temperature MAX3232 configuration (對比MAX3232CPWG4)
- Manufacturer-supported improved family path (對比MAX3232EIPW)
- Direct same-family sourcing option (對比MAX3232IPWR)
設計說明
Place the four 0.1 µF charge-pump capacitors directly beside the pins identified in the manufacturer reference circuit. Keep each capacitor-to-pin loop short and continuous, and avoid routing between the capacitor pads and their associated IC pins. This reduces charge-pump loop inductance and minimizes cable-side switching noise. Preserve the exposed connector and ground-pin layout shown in the datasheet rather than relying on general placement conventions.
Do not substitute a USB-to-serial bridge or a 5 V-only TTL transceiver for this device. The MAX3232IPWRG4 creates true bipolar RS-232 signal levels from a 3- to 5.5-V supply and uses a dedicated pinout. Also verify that a proposed alternative has the same charge-pump capacitor connections and connector-side pin mapping; an equivalent logic interface alone does not guarantee PCB compatibility.
Treat the RS-232 connector pins as an electrostatic-discharge and externally coupled noise entry point. Return connector shell or chassis ground to the enclosure reference appropriate to the installation, and avoid long unprotected traces between the IC and connector. Keep the charge-pump return current close to the device. In laboratory or industrial systems, evaluate whether isolation or additional surge protection is required for the cable length and installation environment.
Route the two transmit and two receive channels according to the manufacturer's reference layout, keeping sensitive receiver nodes away from the switching charge-pump nodes and connector pins. Use a solid ground plane, short receiver traces, and a controlled return path between logic ground and the interface reference. Validate operation with the intended cable because connector grounding, cable geometry, and neighboring switching circuits can materially affect RS-232 noise immunity.
合規資訊
The manufacturer product information confirms TIA/EIA-232-F compatibility and ±15-kV terminal-to-terminal ESD protection. Specific RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations were not identified in the cited product information.