MAX3243ECUI+T - 3/5 RS-232 Transceiver | Analog Devices
MPN: MAX3243ECUI+T ✓ 啟用中MAX3243ECUI+T 概覽
An RS-232 transceiver is an interface IC that converts logic-level UART signals into RS-232 line levels and converts incoming RS-232 signals back into CMOS-compatible logic. In the product hierarchy, the MAX3243 belongs to the RS-232 transceiver class, then to line-driver and receiver ICs, then to interface ICs and semiconductors. This multi-channel device reduces the number of discrete interface packages required when several serial ports share one controller.
The MAX3243 operates from 3.0 V to 5.5 V, allowing operation from either 3.3 V or 5 V system rails. Its three drivers and five receivers support asymmetric port counts common in console, diagnostic, instrumentation, and embedded-control equipment. AutoShutdown disables the internal supply and drivers when the receiver inputs do not detect a valid signal level, reducing standby consumption to approximately 1 µA when supported by the selected power configuration.
The interface provides ±15 kV ESD protection according to the device description, improving tolerance to electrostatic discharge at externally accessible serial connectors. The 250 kbps maximum signaling rate is suitable for legacy RS-232 equipment, industrial consoles, configuration ports, and control links that do not require the throughput of modern differential interfaces. Charge-pump circuitry generates the bipolar voltage required by RS-232 without a separate negative supply.
Typical uses include three-port RS-232 console expansion, multi-channel data acquisition, service interfaces in industrial equipment, instrument control ports, and mixed-voltage embedded systems. The 28-pin TSSOP package supports compact surface-mount layouts while providing enough I/O for five receive inputs, three transmit outputs, power, ground, and control functions.
PCB design should keep charge-pump capacitors close to their associated pins and route driver outputs and receiver inputs away from sensitive analog circuitry. External protection may still be required for long cables or connectors exposed to severe industrial transients. The receiver inputs should also be checked against the selected operating mode and shutdown behavior before finalizing the system power architecture.
This page combines manufacturer specifications, package and interface details, drop-in family options, application guidance, and practical PCB considerations to support faster component selection and replacement planning.
直接替換替代品,適用於 MAX3243ECUI+T — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: MAX3243ECUI+T (相同外形與佔位) — 差異在於 Maximum Data Rate, Package, ESD Protection, RoHS Status, Supply Voltage Range.
MAX3243EEUI+T
✅ 直接替換聯絡詢價
查看資料表 →MAX3243EUI+T
✅ 直接替換 ⚠️ 規格未經驗證聯絡詢價
查看資料表 →MAX3243CUI+T
✅ 直接替換 ⚠️ 規格未經驗證聯絡詢價
查看資料表 →MAX3243AUI+T
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
MAX3243BUI+T
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
MAX3243ECUI+T 規格
| Product Type | RS-232 transceiver |
| Number of Transmitters | 3 |
| Number of Receivers | 5 |
| Supply Voltage Range | 3.0 V to 5.5 V |
| Maximum Data Rate | 250 kbps |
| ESD Protection | ±15 kV |
| AutoShutdown Supply Current | 1 µA |
| Interface Standard | EIA/TIA-232 |
| Signal Standard | V.28 and V.24 |
| 封裝 | 28-pin TSSOP |
| 安裝類型 | Surface mount |
| RoHS 狀態 | Compliant |
| 供應電流 | 1 µA in shutdown operation |
| Driver Configuration | 3 drivers and 5 receivers |
| ESD Standard | IEC-ESD protection |
| Shutdown Feature | AutoShutdown with automatic wakeup |
| Supply Configuration | 3 V to 5.5 V single supply |
MAX3243ECUI+T 28-pin tssop 腳位配置指南
MAX3243ECUI+T(28-pin tssop 封裝)的腳位配置。 腳位編號、功能與連接圖定義於製造商資料手冊中。請參閱該手冊以取得確切的封裝尺寸與焊接指引。
無詳細腳位定義資料: MAX3243ECUI+T.
請參閱 資料表 以查看完整腳位配置。
典型應用
MAX3243ECUI+T 適用於 6 應用s: Industrial Serial Console, Data-Acquisition Equipment, Embedded Equipment Configuration Port, Test and Measurement Instrument, Industrial Control System, Portable Measurement Device.
Industrial Serial Console
The MAX3243ECUI+T is well suited to industrial console and service-port designs because it combines three transmit channels and five receive channels in one 28-pin TSSOP device. Its 3.0 V to 5.5 V supply range allows the interface to share a 3.3 V or 5 V embedded controller rail, while ±15 kV ESD protection adds resilience at an externally accessible connector. The 250 kbps data rate suits configuration and diagnostic links that rely on RS-232 rather than a modern differential bus. AutoShutdown can reduce standby consumption to approximately 1 µA when no valid receiver signal is present, although the selected shutdown configuration must be checked against system start-up behavior.
推薦
Data-Acquisition Equipment
The MAX3243ECUI+T can connect laboratory and industrial data-acquisition equipment that requires more receive channels than transmit channels. Three RS-232 drivers support command paths or multi-drop arrangements, while five receivers can collect status or measurement information from several sources. Operating from 3.0 V to 5.5 V supports mixed-voltage instrumentation, and the 250 kbps rate is adequate for supervisory and control traffic rather than high-volume sensor streaming. The 28-pin TSSOP package conserves board space, but charge-pump capacitors must be placed close to the relevant device pins and each connected cable should receive suitable external surge and ESD protection.
推薦
Embedded Equipment Configuration Port
The MAX3243ECUI+T fits embedded equipment that needs several legacy service interfaces around a central controller. Its 3.0 V to 5.5 V operating range enables use with both 3.3 V microcontrollers and 5 V control logic, reducing level-conversion complexity. The three transmitters can serve independent command or diagnostic outputs, while the five receivers provide status inputs. At 250 kbps, the device supports typical RS-232 configuration protocols. Its approximately 1 µA AutoShutdown supply current is valuable in unattended equipment, although the interface will remain active whenever the receiver circuitry detects a valid signal level.
推薦
Test and Measurement Instrument
The MAX3243ECUI+T is appropriate for test and measurement instruments that expose more RS-232 receive inputs than transmit outputs to an operator or controller. The five receivers can monitor remote commands, interlock states, or trigger acknowledgments, while the three drivers support control and response channels. A 250 kbps rate is generally sufficient for legacy instrument-control protocols, and operation down to 3.0 V supports compact handheld or bench equipment powered by 3.3 V rails. The ±15 kV ESD rating helps manage connector-borne electrostatic discharge, but instrument designers should still assess external cable transients and grounding requirements before publication.
推薦
Industrial Control System
The MAX3243ECUI+T can serve older supervisory control equipment that must exchange RS-232 signals with control boards, service laptops, or peripheral equipment. The three-driver configuration supports separate command channels, while five receiver inputs support monitoring of several modules. Its 3.0 V to 5.5 V supply range enables direct operation from common industrial controller rails, and the 250 kbps signaling rate covers conventional supervisory protocols. AutoShutdown helps reduce power when links are idle, but firmware and wiring must avoid false valid-level detection. A careful ground reference and connector-side protection plan are necessary for reliable operation across industrial cable environments.
推薦
Portable Measurement Device
The MAX3243ECUI+T is useful in portable measurement devices that provide a legacy RS-232 connection while prioritizing battery life. Its approximately 1 µA AutoShutdown supply current allows the interface circuitry to consume very little power when no valid receiver signal is present, while the 3.0 V minimum supply voltage supports 3.3 V portable systems. Three transmit and five receive channels provide flexible connectivity for probes, adapters, or service equipment. The 28-pin TSSOP package also saves board area. Validate the AutoShutdown mode, external line capacitance, connector protection, and system-level leakage requirements because portable RS-232 cables can extend well beyond short on-board traces.
推薦
推薦產品摘要
工程參考資料,適用於 MAX3243ECUI+T — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | MAX3243EEUI+T | MAX3243EUI+T | MAX3243CUI+T | MAX3243AUI+T | MAX3243BUI+T |
|---|---|---|---|---|---|---|
| Package | 28-pin TSSOP | 28-pin TSSOP | 28-pin TSSOP | 28-pin TSSOP | 28-pin TSSOP | 28-pin TSSOP |
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Transmitter Count | 3 | 3 | 3 | 3 | 3 | 3 |
| Receiver Count | 5 | 5 | 5 | 5 | 5 | 5 |
| Supply Voltage Range | 3.0 V to 5.5 V | 3.0 V to 5.5 V | 3.0 V to 5.5 V | 3.0 V to 5.5 V | 3.0 V to 5.5 V | 3.0 V to 5.5 V |
| Maximum Data Rate | 250 kbps | 250 kbps | 250 kbps | 250 kbps | 250 kbps | 250 kbps |
| ESD Protection | ±15 kV | ±15 kV | ±15 kV | ±15 kV | ±15 kV | ±15 kV |
| AutoShutdown Supply Current | 1 µA | 1 µA | 1 µA | 1 µA | 1 µA | 1 µA |
| Interface Standard | EIA/TIA-232 | EIA/TIA-232 | EIA/TIA-232 | EIA/TIA-232 | EIA/TIA-232 | EIA/TIA-232 |
主要差異化特點
- Higher transmit-channel count than single-pair RS-232 interface options (對比MAX232EIPWR)
- Five receive channels support asymmetric RS-232 connectivity (對比MAX3232IPWR)
- 250 kbps signaling rate exceeds comparison listings that identify 120 kbps (對比MAX3243ECAI+T)
- Compact 28-pin TSSOP implementation consolidates multiple RS-232 channels (對比MAX3232ECDR)
設計說明
Place the charge-pump capacitors and their ground returns directly beside the associated MAX3243 pins, following the capacitor values and topology in the manufacturer datasheet. Keep these high-current paths compact because longer loops increase radiated noise and may reduce charge-pump performance. Avoid routing the supply current path through the same copper region used by sensitive receiver inputs.
Keep RS-232 driver outputs and receiver inputs away from clocks, ADC inputs, reference nodes, and other high-impedance analog traces. Connect the device ground to the interface ground with a low-impedance path and use a controlled ground reference between the circuit board and connector. If a cable leaves the enclosure, add suitable connector-side protection because the IC's ±15 kV ESD rating does not replace surge, overvoltage, or isolation components.
Do not assume that all MAX3243E orderings are production-equivalent solely because they use a 28-pin TSSOP package. Check the suffix-specific temperature range, ESD construction, marking, and qualification status before substitution. Also validate AutoShutdown polarity and receiver validity thresholds in firmware because a floating or externally biased receiver input can affect low-power behavior.
合規資訊
RoHS compliance is stated in the MAX3243ECUI+T product listing. No separate REACH, automotive-grade, lead-free, halogen-free, or conflict-minerals declaration was established.