MAX361ESE+ - 85 Ohm Quad SPST Analog Switch | Maxim Integrated
MPN: MAX361ESE+ ✓ 啟用中MAX361ESE+ 概覽
An analog switch is an integrated semiconductor device that routes signals between circuit nodes under digital control. The MAX361ESE+ belongs to the analog switch and multiplexer category, where its normally closed SPST architecture connects each input to its corresponding output when the control state is inactive. The four channels provide convenient parallel routing without requiring four separate discrete switch packages.
The main electrical feature of the MAX361ESE+ is its maximum channel on resistance of 85 ohms. Maxim specifies that channel resistance is guaranteed to match within 3 ohms between channels and remain flat over the analog signal range, with a maximum variation of 9 ohms. This matching behavior is important in precision systems because unequal channel resistance can create gain errors, distortion, or inconsistent attenuation when different channels are selected.
The MAX361ESE+ is a single-pole single-throw device with four normally closed switches. Its control interface supports external digital control of the four signal paths, allowing an instrument, measurement system, or controller to select a signal route while minimizing external discrete components. The device is also specified for low leakage, which helps preserve the integrity of high-impedance measurement nodes when switches are open.
Typical applications include precision instrumentation, automated test equipment, multiplexed sensor interfaces, signal patching, sample-and-hold systems, and laboratory measurement setups. In these systems, the four matched channels can route several sensor or reference signals into a common measurement chain while reducing insertion-resistance variation between channels.
The principal design consideration is signal integrity. Traces connected to the analog pins should be kept short, and the switch should be placed close to the source and destination circuitry when possible. Power-supply bypassing and grounding are important in high-impedance systems because parasitic capacitance and leakage can degrade the measured signal even when the nominal on-resistance is well controlled.
This page combines the manufacturer product information, verified distributor listings, package details, comparison data, and practical routing guidance for engineers evaluating the MAX361ESE+ in precision analog-switch designs.
直接替換替代品,適用於 MAX361ESE+ — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: MAX361ESE+ (相同外形與佔位) — 差異在於 Number of Switches, On Resistance, On-Resistance Matching Between Channels, On-Resistance Variation Over Analog Signal Range, Package.
MAX361ESE
✅ 直接替換📋 參考替代品(不在目錄中)
MAX361CSE+
✅ 直接替換聯絡詢價
查看資料表 →MAX353CSE+
✅ 直接替換📋 參考替代品(不在目錄中)
MAX361ESE+ 最大額定值與電氣特性
| Number of Switches | 4 |
| Configuration | 1:1 |
| Switch Type | SPST, normally closed |
| On Resistance | 85 ohm maximum |
| On-Resistance Matching Between Channels | 3 ohm maximum |
| On-Resistance Variation Over Analog Signal Range | 9 ohm maximum |
| On-Resistance Flatness | Flat over the analog signal range |
| 封裝 | 16-SOIC |
| Package Pin Count | 16 pins |
| 安裝類型 | Surface mount |
| RoHS 狀態 | unknown |
| AEC-Q100 Qualification | not_applicable |
| Manufacturer Product Family | MAX361 precision quad SPST analog switches |
MAX361ESE+ 16 pins 腳位配置指南
MAX361ESE+(16 pins 封裝)的腳位配置。 腳位編號、功能與連接圖定義於製造商資料手冊中。請參閱該手冊以取得確切的封裝尺寸與焊接指引。
無詳細腳位定義資料: MAX361ESE+.
請參閱 資料表 以查看完整腳位配置。
典型應用
MAX361ESE+ 適用於 6 應用s: Precision Test Equipment Signal Routing, Multiplexed Sensor Interfacing, High-Impedance Measurement Systems, Automated Signal Patching, Instrumentation Signal Selection, Laboratory Reference Distribution.
Precision Test Equipment Signal Routing
The MAX361ESE+ fits precision test-equipment routing because it provides four normally closed SPST channels with maximum on resistance of 85 ohms. The manufacturer specifies channel matching within 3 ohms and maximum resistance variation of 9 ohms over the analog signal range, helping preserve consistent attenuation as different test paths are selected. Place the switch close to the instrument input or source buffer, keep analog traces short, and provide local bypassing to minimize added insertion error and parasitic pickup. The four independent channels allow several fixtures or reference nodes to share a measurement path without requiring four discrete switch packages.
推薦
Multiplexed Sensor Interfacing
The MAX361ESE+ is useful for multiplexing several sensor signals into a shared acquisition channel. Its four normally closed switches provide a defined default connection state, while the 85-ohm maximum on resistance and 3-ohm channel match limit path-dependent errors between sensors. For resistive sensors, calculate the maximum source impedance and acquisition time to ensure the added switch resistance does not impair settling. Keep high-impedance sensor nodes surrounded by grounded guarding where appropriate, and verify leakage requirements because switch off-state leakage can establish the measurement noise floor.
推薦
High-Impedance Measurement Systems
The MAX361ESE+ can serve as a controlled routing element in high-impedance measurement systems where consistent channel resistance and low leakage are important. The guaranteed 3-ohm maximum match between channels helps reduce channel-dependent error when a common amplifier or ADC measures different sources. The device should be placed close to the guarded input node, with short traces and clean power grounding to prevent leakage and capacitance from dominating the measurement. Confirm the complete leakage, bandwidth, and capacitance specifications against the required source impedance and settling-time budget before using it near picoamp-level front ends.
推薦
Automated Signal Patching
The MAX361ESE+ is appropriate for automated signal-patching systems that route several low- or moderate-impedance analog nodes into a common processing chain. Four SPST channels in one 16-SOIC package reduce board area compared with four separate single switches. The controlled 85-ohm maximum on resistance gives the system designer a defined insertion loss budget, while 3-ohm channel matching improves repeatability between routes. Use short traces from each source to its switch pin, avoid sharing high-resistance nodes where possible, and validate the complete control sequence during power-up to prevent unintended signal application.
推薦
Instrumentation Signal Selection
The MAX361ESE+ supports instrumentation signal selection where multiple inputs must be presented to a shared buffer, amplifier, or converter. Its normally closed SPST topology provides a predictable default path, and its specified resistance matching makes channel-to-channel comparisons more repeatable than an unqualified general-purpose switch. The designer should still include the switch resistance in the source-loading calculation and assess the measurement settling time under the maximum source impedance. Grounding and bypass-pin placement are critical because long analog traces and shared supply return paths can introduce errors larger than the 3-ohm channel-match guarantee.
推薦
Laboratory Reference Distribution
The MAX361ESE+ can distribute a selected reference or calibration signal across several measurement channels. Matching within 3 ohms between channels is especially helpful when the same reference is compared across multiple paths, because it limits route-dependent amplitude differences. Keep the switch and source network close together, use a low-impedance reference driver when appropriate, and confirm the maximum signal voltage and supply conditions from the manufacturer datasheet. For precision calibration, characterize the actual insertion resistance and leakage in the final layout rather than relying only on the nominal 85-ohm maximum specification.
推薦
推薦產品摘要
工程參考資料,適用於 MAX361ESE+ — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | MAX361ESE | MAX361CSE+ | MAX353CSE+ |
|---|---|---|---|---|
| Package | 16-SOIC | 16-SOIC | SOIC-16 | SOIC-16 |
| Brand | Maxim Integrated | Maxim Integrated | Maxim Integrated | Maxim Integrated |
| Number of Channels | 4 | 4 | 4 | 4 |
| Switch Configuration | Quad SPST | 4 x SPST | 4 x SPST | 4 x SPST |
主要差異化特點
- Four normally closed channels in one package (對比MAX353CSE+)
- Defined channel-to-channel resistance matching (對比MAX353CSE+)
- Verified same-family ordering alternatives (對比MAX361CSE+)
設計說明
Place the MAX361ESE+ close to the source, destination, or shared measurement node so that switch resistance and parasitic capacitance do not become significant parts of the signal path. Keep analog traces short, avoid unnecessary stubs, and route control signals away from sensitive input traces. For high-impedance nodes, use guarding and a clean ground reference to prevent leakage and capacitive pickup from overwhelming the signal.
Use local supply bypassing and verify the control-pin voltage levels from the manufacturer datasheet before connecting digital control signals to the switch. The MAX361ESE+ is an analog-routing device, but supply and control transitions can inject disturbance into nearby analog paths. Keep the bypass capacitor close to the device supply pins, provide an adequate return path, and sequence control outputs so that unintended signal combinations are not created during startup.
Do not treat the 85-ohm on resistance as the only error term. Include the source impedance, switch on resistance, input capacitance, amplifier bias error, and leakage current in the measurement or signal-transfer budget. When substituting a candidate, verify the complete pinout, control polarity, supply requirements, signal range, and temperature grade rather than relying on package shape alone.
合規資訊
The MAX361 is an analog interface IC and is not identified as an AEC-Q100 automotive device in the manufacturer product information. Specific RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations were not stated in the verified product data.