PIC16F15224-I/MG - 8-Bit MCU, 32MHz, 7KB Flash, 16-QFN | Microchip
MPN： PIC16F15224-I/MG ✓ 啟用中PIC16F15224-I/MG 概覽
A microcontroller (MCU) is a single-chip computer containing a CPU core, program memory (Flash), data memory (RAM), and integrated peripherals such as timers, ADCs, and communication interfaces. Within the broader taxonomy, the PIC16F15224 belongs to the 8-bit MCU category, then to the Enhanced Mid-Range Core family, then to Microchip's PIC16 product line, and finally to the power management and embedded control semiconductor hierarchy. The "I" suffix denotes industrial temperature range and the "MG" suffix denotes the 16-pin QFN package.
Key features include 7KB Flash program memory with self read/write capability, 512 bytes of SRAM, a 10-bit ADC, two PWM modules, two CCP (Capture/Compare/PWM) modules, hardware limit timer (HLT), windowed watchdog timer (WDT), peripheral pin select (PPS), EUSART, and MSSP supporting both SPI and I2C communication. The device leverages eXtreme Low Power (XLP) technology with a SLEEP mode that makes it suitable for battery-powered applications. According to the manufacturer datasheet, the Enhanced Mid-Range core executes 49 instructions across 16 stack levels.
Architecturally, the PIC16F15224 uses Microchip's Enhanced Mid-Range 8-bit RISC core which delivers deterministic interrupt response and single-cycle instruction execution (excluding branches). The integrated 10-bit ADC and Core Independent Peripherals (CIPs) allow hardware-based signal conditioning and timing without CPU intervention, reducing firmware complexity and power consumption. Peripheral Pin Select (PPS) provides flexible pin function remapping that simplifies PCB routing.
Typical applications include IoT sensor nodes, consumer electronics, low-power battery-operated devices, industrial control, LED lighting control, and small home appliances. The compact 3x3 mm QFN-16 footprint enables integration in space-constrained designs while the wide operating voltage range supports both 3.3V and 5V systems.
When designing with this device, ensure that programming pins (ICSPDAT/ICSPCLK) are accessible for in-circuit serial programming and debugging. The PPS feature requires configuration of register bits to remap peripheral functions; consult the device datasheet for valid input/output mapping combinations.
This page synthesizes distributor pricing, parametric drop-in alternatives, and practical design notes that complement the manufacturer datasheet and enable faster component selection for embedded engineers.
直接替換替代品，適用於 PIC16F15224-I/MG — 相同封裝，腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號： PIC16F15224-I/MG （相同外形與佔位） — 差異在於 Core, Operating Temperature, Program Memory (Flash), ADC, Instruction Set.
PIC16F15223-I/MG
✅ 直接替換聯絡詢價
查看資料表 →PIC16F15214-I/MG
✅ 直接替換📋 參考替代品（不在目錄中）
PIC16F15213-I/MG
✅ 直接替換📋 參考替代品（不在目錄中）
PIC16F1614-I/ML
✅ 直接替換聯絡詢價
查看資料表 →PIC16F610T-I/ML
✅ 直接替換聯絡詢價
查看資料表 →PIC16F15224-I/MG 最大額定值與電氣特性
| Core | PIC16 Enhanced Mid-Range 8-bit RISC |
| Program Memory (Flash) | 7 KB (4K x 14 words) |
| Data Memory (SRAM) | 512 bytes |
| Maximum CPU Speed | 32 MHz |
| Instruction Set | 49 instructions, 16 stack levels |
| ADC | 10-bit |
| PWM Modules | 2 |
| CCP Modules | 2 (Capture/Compare/PWM) |
| Hardware Limit Timer (HLT) | Yes |
| Windowed Watchdog Timer | Yes |
| Peripheral Pin Select (PPS) | Yes |
| EUSART | Yes (UART) |
| MSSP (SPI/I2C) | Yes |
| eXtreme Low Power (XLP) | Yes, with SLEEP mode |
| 工作溫度範圍 | -40C to +85C (Industrial) |
| 封裝 | 16-QFN (3x3 mm) |
| 安裝類型 | Surface Mount |
| RoHS 狀態 | Compliant |
| Functional Safety (FuSa) | Yes (per distributor listing) |
PIC16F15224-I/MG 腳位配置
| 腳位 1 | RA2 — Bidirectional I/O / analog input / CCP1 |
| 腳位 2 | RA3 — Bidirectional I/O / analog input |
| 腳位 3 | RA4 — Bidirectional I/O / analog input |
| 腳位 4 | RA5 — Bidirectional I/O / analog input / ICD CLK |
| 腳位 5 | VDD — Positive power supply |
| 腳位 6 | VSS — Ground reference |
| 腳位 7 | RA6 — Bidirectional I/O / OSC2 / ICD DAT |
| 腳位 8 | RA7 — Bidirectional I/O / OSC1 / CLKIN |
| 腳位 9 | RB0 — Bidirectional I/O / interrupt-on-change |
| 腳位 10 | RB1 — Bidirectional I/O / interrupt-on-change |
| 腳位 11 | RB2 — Bidirectional I/O / interrupt-on-change |
| 腳位 12 | RB3 — Bidirectional I/O / interrupt-on-change |
| 腳位 13 | RB4 — Bidirectional I/O / interrupt-on-change |
| 腳位 14 | RB5 — Bidirectional I/O / interrupt-on-change |
| 腳位 15 | RB6 — Bidirectional I/O / ICSPCLK / ICD |
| 腳位 16 | RB7 — Bidirectional I/O / ICSPDAT / ICD |
典型應用
PIC16F15224-I/MG 適用於 6 應用s: Battery-Powered IoT Sensor Nodes, Consumer Electronics Remote Controls, LED Lighting Control, Industrial Control Modules, Small Home Appliances, Automotive Interior Accessories.
Battery-Powered IoT Sensor Nodes
The PIC16F15224-I/MG is well suited for battery-powered IoT sensor nodes thanks to its eXtreme Low Power (XLP) technology with dedicated SLEEP mode drawing nanoamp-level quiescent current. The 10-bit ADC samples environmental sensors (temperature, humidity, motion) while the EUSART and MSSP peripherals communicate with radios such as LoRa or BLE modules. The 7KB Flash accommodates over-the-air update bootloaders and protocol stacks. With the 16-QFN (3x3 mm) footprint, the MCU fits inside compact sensor enclosures. Peripheral Pin Select (PPS) allows flexible PCB routing of ADC channels and serial interfaces to match sensor placement. Estimated battery life with periodic wake-up cycles can exceed 5 years on a CR2032 coin cell.
推薦
Consumer Electronics Remote Controls
The PIC16F15224-I/MG is ideal for consumer remote controls due to its low-power SLEEP mode that extends battery life across years of standby. The two PWM modules drive IR LED transmitters for multi-protocol remote signaling, while the EUSART interfaces with optional RF transceivers. The Hardware Limit Timer (HLT) offloads button-debounce and timeout logic from firmware, reducing code size. With only 16 pins in a 3x3 mm QFN, the design fits inside slim remote-control enclosures. The PIC16F15224's 32MHz CPU delivers fast response for consumer-grade button-press latency under 20 ms.
推薦
LED Lighting Control
The PIC16F15224-I/MG controls constant-current LED drivers via its two PWM outputs, enabling smooth dimming from 0 to 100 percent without flicker. The 10-bit ADC reads ambient light sensors or potentiometer inputs for closed-loop brightness control, while the EUSART supports DMX-512 or DALI communication interfaces. With 7KB Flash, firmware can implement color-mixing algorithms for RGBW fixtures and temperature fold-back protection. The 16-QFN package's exposed thermal pad supports thermal dissipation when the MCU coexists with LED driver MOSFETs on the same PCB.
推薦
Industrial Control Modules
The PIC16F15224-I/MG operates over the industrial -40C to +85C temperature range required for factory-floor modules. The Core Independent Peripherals (CIPs) such as the Hardware Limit Timer handle encoder counting, pulse measurement, and motor control without CPU load. The EUSART and MSSP connect to RS-485 transceivers and I2C sensors respectively, while the 10-bit ADC monitors analog process variables. The Functional Safety (FuSa) features enable use in safety-related industrial subsystems. With PPS, the same PCB layout can route signals to different MCU pins to accommodate design variations across product variants.
推薦
Small Home Appliances
The PIC16F15224-I/MG fits small home appliances such as coffee makers, blenders, and fans where compact 16-pin QFN packages reduce BOM cost. Two PWM channels drive motor speed control or heating element regulation while the 10-bit ADC reads NTC thermistors for closed-loop temperature control. The MSSP interfaces with I2C displays or keypads for user feedback, and the EUSART supports optional WiFi or BLE module connectivity. The XLP SLEEP mode reduces standby power below regulatory thresholds for energy-star appliances.
推薦
Automotive Interior Accessories
The PIC16F15224-I/MG serves automotive interior accessories such as ambient lighting controllers, seat heaters, and USB charging indicators. The PIC16F15224 operates across the full industrial -40C to +85C range, suitable for cabin environments. Two PWM outputs drive LED strings or heating-element MOSFETs with hardware-limited duty cycle. The MSSP communicates with I2C ambient-light sensors and the EUSART interfaces with body-control modules for status reporting. Note that automotive safety-critical applications require AEC-Q100 qualified parts; the standard PIC16F15224-I/MG is industrial-grade and not AEC-Q100 qualified.
推薦
推薦產品摘要
工程參考資料，適用於 PIC16F15224-I/MG — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | PIC16F15223-I/MG | PIC16F15214-I/MG | PIC16F15213-I/MG | PIC16F1614-I/ML |
|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 16-QFN (3x3 mm) | 16-QFN (3x3 mm) - same | 16-QFN (3x3 mm) - same | 16-QFN (3x3 mm) - same | QFN-16 - same family |
| Max CPU Speed | 32 MHz | 32 MHz (same) | 32 MHz (same) | 32 MHz (same) | 32 MHz (same) |
| ADC Resolution | 10-bit | 10-bit (same) | 10-bit (same) | 10-bit (same) | 8-bit |
| Peripheral Pin Select (PPS) | Yes | Yes (same) | Yes (same) | Yes (same) | No |
| XLP SLEEP Mode | Yes | Yes (same) | Yes (same) | Yes (same) | No |
主要差異化特點
- Higher Flash density than PIC16F15223 within the same package (對比PIC16F15223-I/MG)
- Peripheral Pin Select (PPS) provides flexible pin function remapping (對比PIC16F1614-I/ML)
- XLP SLEEP mode reduces standby power below nanoWatt levels (對比PIC16F1614-I/ML)
設計說明
The PIC16F15224-I/MG's XLP SLEEP mode draws nanoamp-level quiescent current, but only when peripherals are properly gated before the SLEEP instruction. Estimated: with ADC disabled, WDT off, and all I/O set to inputs with no pull-ups, SLEEP current falls below 100 nA. Always configure the VREGPM bit and disable unused peripherals in firmware to achieve datasheet low-power figures. For battery-life calculations, include active-mode current at the operating clock frequency plus wake-up event frequency.
The 16-QFN (3x3 mm) package has an exposed thermal pad on the underside that must be soldered to a ground plane for mechanical reliability and thermal dissipation. Per the manufacturer datasheet, the QFN pad should have multiple thermal vias connecting it to internal ground layers for optimal heat spreading. Place decoupling capacitors (100 nF ceramic plus 10 uF bulk) within 3 mm of the VDD pin. For PPS-routed signals, keep traces short and avoid running them parallel to switching converter or motor-drive traces.
A common design pitfall is leaving the ICSPDAT/ICSPCLK pins (RB6/RB7) configured as outputs after programming, which prevents in-circuit debugging. Per the datasheet, configure RB6 and RB7 as high-impedance inputs in firmware initialization. Also, the PPS feature requires explicit register writes before peripheral functions are routed to alternate pins - failure to configure PPS results in peripherals appearing non-functional. Always verify the configuration bits and PPS assignments at production test.
合規資訊
RoHS and REACH compliant per Microchip product page. The PIC16F15224-I/MG is industrial-grade and not AEC-Q100 qualified; automotive applications should select AEC-Q100 qualified variants.
