SY89808LTI - 500MHz 1:9 Differential HSTL Buffer | Microchip
MPN: SY89808LTI ✓ AktifSY89808LTI Ringkasan
A differential fanout buffer is a clock-and-timing semiconductor that preserves a differential clock or data signal while distributing it to multiple destinations. Its role in the hierarchy is clock buffer → fanout buffer → clock and timing IC → semiconductor. HSTL is a low-swing, source-terminated signaling method commonly used for high-speed digital interconnects. Translating and buffering the signal at the distribution point helps drive multiple loads without loading the original source.
The SY89808LTI’s principal specifications are its 500 MHz operating frequency, 1:9 fanout ratio, 3.3 V supply voltage, differential input and output architecture, and 1.5 V HSTL signal level. These characteristics make the device applicable where one high-speed differential source must reach multiple downstream circuits while maintaining a consistent voltage interface. The 1:9 ratio allows a single input branch to feed nine output branches without requiring nine separate source buffers.
The differential architecture is particularly useful when signal integrity depends on matched edge timing through a multi-drop board topology. A common source can drive the buffer input, while the nine outputs provide local distribution points for receivers, controllers, memory interfaces, or downstream clock-generating circuits. Because skew and return-loss performance depend on PCB topology, trace length matching, termination, and reference-plane continuity, the implementation around the device is as important as the stated operating frequency.
Typical uses include high-speed parallel-processing systems, networking and communications equipment, test and measurement systems, data-conversion platforms, and clock distribution around FPGAs or other digital controllers. A single high-speed differential clock can be distributed to multiple parallel destinations, while the translator function supports interfacing between 1.5 V HSTL logic and circuitry operating from a 3.3 V supply.
For a new layout, place the device so that input and output differential pairs have matched impedances and controlled length. Follow the manufacturer’s pin-description and layout guidance when assigning termination and decoupling. Avoid introducing long stubs between the outputs and their receivers because stubs can create reflections that reduce the usable bandwidth below the 500 MHz device capability.
This product page consolidates the verified SY89808LTI function, package, interface, and sourcing information with practical clock-distribution guidance. It also identifies where detailed electrical, pin-level, environmental, and lifecycle information must be confirmed in the manufacturer datasheet before a production design is released.
Alternatif penggantian untuk SY89808LTI — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
SY89808LTG
✅ Drop-InKontak untuk harga
Lihat Datasheet →SY89808LTI Spesifikasi
| Product Type | Differential HSTL fanout buffer/translator |
| Tegangan Pemuat | 3.3 V |
| Maximum Operating Frequency | 500 MHz |
| Fanout Ratio | 1:9 |
| Signal Interface | Differential HSTL |
| HSTL Signal Voltage | 1.5 V |
| Jumlah Output | 9 differential outputs |
| Input Configuration | 1 differential input |
| Logic Family | HSTL |
| Paket | 32-pin TQFP |
| Tipe Mounting | Surface mount |
SY89808LTI 32-pin tqfp Diamant Konfigurasi Panduan
Konfigurasi pin untuk SY89808LTI (32-pin tqfp pakai pakai). Penomoran pin, fungsi, dan diagram koneksi ditetapkan dalam datasheet produsen. Lihatnya untuk footprint dan pedoman perpindahan paruh.
Tidak ada data diatribut pin yang tersedia untuk SY89808LTI.
Lihat ke: datasheet produk untuk konfigurasi pin penuh.
Aplikasi Umum
SY89808LTI cocok untuk 6 aplikasis: High-Speed Clock Distribution, FPGA Parallel-Interface Support, Communications Equipment, Parallel Data Distribution, Test and Measurement Systems, Data-Conversion Platforms.
High-Speed Clock Distribution
The SY89808LTI fits a single-source, nine-destination clock tree because its 1:9 differential HSTL fanout ratio can distribute one clock to nine branches at up to 500 MHz. Place the source at the input and route each differential output as a controlled-impedance pair to its assigned receiver. The 3.3 V supply and 1.5 V HSTL interface support low-swing distribution, while matched trace geometry and source termination help limit timing degradation.
Direkomendasikan
FPGA Parallel-Interface Support
The SY89808LTI can distribute a 500 MHz differential clock across nine parallel FPGA or controller domains. Its one-input, nine-output differential arrangement avoids combining multiple long loads directly at the clock source and gives each branch a defined fanout point. The HSTL interface operates at 1.5 V from a 3.3 V supply. Board implementation should preserve pair symmetry, provide continuous reference planes, and avoid stubs that could reflect clock energy.
Direkomendasikan
Communications Equipment
The SY89808LTI is applicable in communications equipment that requires a high-speed differential source to reach multiple timing domains. Its 500 MHz capability and 1:9 fanout ratio suit central clock distribution in line cards, interface modules, and backplane-related logic. The 3.3 V-powered, 1.5 V HSTL interface provides a defined signaling method, while proper source termination and impedance-controlled routing are essential to preserve edge quality across the board.
Direkomendasikan
Parallel Data Distribution
The SY89808LTI can translate and fan out a differential HSTL signal when multiple high-speed data paths require synchronized distribution. Its 1:9 architecture gives designers a practical way to separate nine destinations from one source, while the 500 MHz rating addresses demanding parallel interfaces. Because timing margin depends on skew and edge degradation, route each output as a matched pair and verify the complete channel against receiver thresholds and termination requirements.
Direkomendasikan
Test and Measurement Systems
The SY89808LTI is suited to clock distribution in test and measurement equipment where a common differential stimulus must reach multiple acquisition, capture, or processing paths. The 1:9 fanout ratio supports branched clock trees at up to 500 MHz, and the translator function provides a 1.5 V HSTL interface from a 3.3 V supply. Layout should minimize branch length differences and connector-related discontinuities so channel-to-channel timing remains predictable.
Direkomendasikan
Data-Conversion Platforms
The SY89808LTI can provide a common differential clock to multiple converters and digital processing blocks in a high-speed data-acquisition platform. Its nine differential outputs simplify fanout architecture, while the 3.3 V supply and 1.5 V HSTL level suit systems with compact high-speed interfaces. The device should be positioned centrally enough to limit trace lengths, and each pair requires matched geometry, suitable return paths, and termination selected from the manufacturer’s reference design.
Direkomendasikan
Ringkasan Produk Direkomendasikan
Data referensi engineering untuk SY89808LTI — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | SY89808LTG |
|---|---|---|
| Brand | Microchip Technology | Microchip Technology |
| Package | 32-pin TQFP | 32-pin TQFP |
| Product Type | Differential HSTL fanout buffer/translator | Differential HSTL fanout buffer/translator |
| Operating Frequency | 500 MHz | 500 MHz |
| Signal Interface | Differential HSTL | Differential HSTL |
Diferensiator Kunci
- One-to-nine differential fanout in a single device (vsSY89808LTG)
- Integrated HSTL translation and clock distribution (vsSY89808LTG)
- High-speed differential distribution (vsSY89808LTG)
Catatan Desain
Route every differential pair with matched geometry, continuous reference planes, and the impedance specified by the manufacturer’s interface guidance. Keep the input pair and each output pair as short as practical, maintain consistent spacing between pair members, and avoid vias that unnecessarily disrupt return paths. At the 500 MHz capability of the SY89808LTI, trace discontinuities and reference-plane changes can degrade edge quality even when the nominal clock frequency is correct.
Use the manufacturer’s recommended HSTL source-termination and output configuration instead of applying generic low-voltage termination by analogy. Termination values depend on trace impedance, receiver topology, source resistance, and whether outputs are lightly loaded. Keep output stubs exceptionally short because a capacitive stub can act as a discontinuity and reflect energy back into the buffer, reducing rise time and potentially causing double-edge or ringing behavior.
Do not treat the 1:9 fanout rating as permission to create nine arbitrary long branches. Match branch topology where channel-to-channel timing matters, preserve differential symmetry, and verify source, output, and receiver loading in simulation. The SY89808LTI is a clock-and-timing distribution device, not a general-purpose logic buffer, and its HSTL interface requires deliberate termination and routing.
Informasi Konformitas
Compliance attributes are not stated in the available product and distributor records. Confirm RoHS, REACH, automotive qualification, lead-free, halogen-free, and conflict-minerals status using the manufacturer’s current product documentation or declarations.