TLV2404IN - 16V Quad 5.5kHz RRIO Op Amp | Texas Instruments
MPN: TLV2404IN ✓ 啟用中TLV2404IN 概覽
An operational amplifier is an analog signal-processing IC that uses high open-loop gain to amplify the difference between two input voltages. A rail-to-rail input stage accepts common-mode voltages across most of the supply range, while a rail-to-rail output stage can swing close to either supply rail. Within the amplifier hierarchy, the TLV2404IN belongs to the micropower operational-amplifier class and supports applications such as sensor conditioning, battery-powered instrumentation, current measurement, filtering, and low-frequency control loops.
Key features include four amplifier channels in one package, a 5.5 kHz gain-bandwidth product, rail-to-rail inputs and outputs, reverse-battery protection, and an approximately 880 nA per-channel quiescent current. Reverse-battery protection is particularly useful in portable systems where a misconnected battery can place reverse voltage across the device. The slow 5.5 kHz bandwidth favors low-frequency precision and sensing functions rather than high-speed signal processing.
The TLV2404IN combines four rail-to-rail amplifiers with a micropower bias architecture. Its low quiescent current reduces supply drain in continuously powered equipment, while the wide common-mode input capability simplifies buffering of sensors whose operating range lies close to a supply rail. Because this is a general-purpose amplifier rather than a high-speed comparator, designers should account for its limited gain-bandwidth product when setting filter poles, closed-loop gain, and required settling behavior.
Typical applications include portable battery-powered monitors, industrial sensor interfaces, low-frequency active filters, current-sense amplifier signal chains, and general-purpose analog instrumentation. A four-channel implementation can reduce board area when several independent low-frequency signals require amplification, provided each channel's noise, offset, common-mode range, and stability requirements are compatible.
When designing around the TLV2404IN, check source and sink current capability at the chosen output voltage, place decoupling capacitors close to the supply pins, and confirm that each feedback network supports the intended operating frequency. Avoid treating reverse-battery protection as a substitute for correct battery polarity or for a dedicated fuse and protection network.
This product page consolidates the exact TLV2404IN device characteristics, family-level alternatives, application guidance, pin-package constraints, and practical design notes into an engineering-focused reference for evaluating the amplifier before PCB implementation.
直接替換替代品,適用於 TLV2404IN — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: TLV2404IN (相同外形與佔位) — 差異在於 Reverse-Battery Protection.
TLV2404CN
✅ 直接替換 ⚠️ 規格未經驗證聯絡詢價
查看資料表 →TLV2404IP
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
TLV2404INE4
✅ 直接替換📋 參考替代品(不在目錄中)
TLV2404IN 最大額定值與電氣特性
| Number of Amplifier Channels | 4 channels |
| Maximum Supply Voltage | 16 V |
| Gain-Bandwidth Product | 5.5 kHz |
| 靜態電流 | Approximately 880 nA per channel |
| Input Common-Mode Range | Rail-to-rail |
| Output Swing | Rail-to-rail |
| Reverse-Battery Protection | Supported |
| 工作溫度範圍 | -40 °C to 125 °C |
| Package Type | PDIP (N) |
| 腳位數 | 14 pins |
| 安裝類型 | Through-hole |
| Product Type | Quad micropower rail-to-rail input/output operational amplifier |
| Operating Class | General-purpose amplifier |
| Primary Device Family | TLV2404 |
| Supplier Segment | Instrumentation and operational-amplifier applications |
TLV2404IN pdip (n) 腳位配置指南
TLV2404IN(pdip (n) 封裝)的腳位配置。 此類比元件具有輸入、輸出與電源腳位。偏移歸零、補償與致能腳位配置請參閱製造商資料表。適用於訊號調理與放大器電路。
無詳細腳位定義資料: TLV2404IN.
請參閱 資料表 以查看完整腳位配置。
典型應用
TLV2404IN 適用於 6 應用s: Battery-Powered Sensor Conditioning, Industrial Process Measurement, Low-Frequency Active Filtering, Portable Medical Monitoring, Current Measurement Signal Chain, Data Acquisition Interface.
Battery-Powered Sensor Conditioning
The TLV2404IN suits low-frequency sensor-conditioning channels because four rail-to-rail amplifiers are integrated in one 14-pin PDIP package and quiescent current is approximately 880 nA per channel. A current sensor, thermistor, or resistive bridge can be conditioned with separate amplifier stages while keeping continuous supply drain low. The rail-to-rail input stage helps accept signals near the supply limits, and the rail-to-rail output stage provides more usable output range than a fixed-rail implementation. Because the gain-bandwidth product is 5.5 kHz, this device is intended for slow measurements rather than fast transients.
推薦
Industrial Process Measurement
The TLV2404IN can condition several low-frequency industrial process signals when the design requires a common quad-amplifier package and a 16 V maximum supply rating. Each channel may buffer a thermocouple interface, pressure-sensor signal, or scaled plant-control voltage. Rail-to-rail inputs and outputs improve headroom when operating from lower supply voltages, while approximately 880 nA per channel is valuable in remotely powered instrumentation. The 5.5 kHz bandwidth is adequate for slow process variables, but loop compensation and sensor-response requirements must be checked to ensure the resulting closed-loop bandwidth remains sufficient.
推薦
Low-Frequency Active Filtering
The TLV2404IN is appropriate for active filters and shaping networks operating below its 5.5 kHz gain-bandwidth product. Four channels can implement two cascaded second-order filters, a fourth-order low-pass or high-pass section, or several separate signal-conditioning stages. Rail-to-rail operation helps preserve signal amplitude in low-voltage systems, while the approximately 880 nA per-channel bias supports compact, low-power monitoring equipment. Component selection should account for closed-loop gain, noise gain, output loading, and the amplifier's phase-margin behavior rather than treating 5.5 kHz as a guaranteed usable filter cutoff.
推薦
Portable Medical Monitoring
The TLV2404IN can support low-frequency conditioning paths in portable monitoring equipment where four amplifier channels and low quiescent current simplify power budgeting. A bridge sensor, bio-sensor analog front end, or patient-monitoring transducer may use separate channels for buffering, gain, filtering, and output drive. The -40 °C to 125 °C rating provides a broad environmental range, while rail-to-rail inputs and outputs help use the available supply voltage efficiently. Medical-system designers must separately validate patient protection, isolation, leakage, electromagnetic compatibility, and applicable regulatory requirements for the finished instrument.
推薦
Current Measurement Signal Chain
The TLV2404IN is useful after a current-sense amplifier when the system requires additional filtering, level shifting, or output buffering across multiple channels. Its approximately 880 nA per-channel quiescent current minimizes overhead in portable or distributed power systems, and the 16 V maximum supply rating supports common industrial and automotive-style rails when the complete signal path meets the device limits. The rail-to-rail output can improve utilization of the output range. Applications needing faster transient capture or very low amplifier noise should compare the TLV2404's 5.5 kHz bandwidth against their measurement bandwidth.
推薦
Data Acquisition Interface
The TLV2404IN can provide buffering and channel conditioning ahead of a moderately slow data-acquisition system. Four independent channels may handle analog inputs from sensors, dividers, or level-shifting networks, while the 5.5 kHz gain-bandwidth product suits sampled measurements whose relevant signal content is low frequency. Rail-to-rail inputs help accommodate sensor outputs that approach the supply range, and the low quiescent current supports compact multi-channel acquisition equipment. The ADC, sampling rate, anti-alias filter, settling requirements, and input-source impedance must be evaluated together to verify the complete acquisition path.
推薦
推薦產品摘要
工程參考資料,適用於 TLV2404IN — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | TLV2404CN | TLV2404IP | TLV2404INE4 |
|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | PDIP-14 (N) | PDIP-14 (N) | PDIP-14 (N) | PDIP-14 (N) |
| Number of Channels | 4 channels | 4 channels | 4 channels | 4 channels |
| Maximum Supply Voltage | 16 V | 16 V | 16 V | 16 V |
| Gain-Bandwidth Product | 5.5 kHz | 5.5 kHz | 5.5 kHz | 5.5 kHz |
| Input Common-Mode Range | Rail-to-rail | Rail-to-rail | Rail-to-rail | Rail-to-rail |
| Output Swing | Rail-to-rail | Rail-to-rail | Rail-to-rail | Rail-to-rail |
主要差異化特點
- Four rail-to-rail amplifiers in one through-hole package (對比TLV2404IP)
- Low-power bias supports continuous instrumentation (對比TLV2404CN)
- Exact TLV2404IN ordering configuration (對比TLV2404INE4)
設計說明
Route each amplifier's supply and ground connections directly to the nearest package pins, and place the supply-decoupling capacitor close to the device. For a four-channel package, separate analog input traces from output and supply paths to reduce coupling between channels. Keep feedback components close to the relevant amplifier inputs and outputs so parasitic capacitance does not destabilize the 5.5 kHz-gain-bandwidth device.
Do not treat reverse-battery protection as a complete battery-safety solution. Verify the exact protection conditions, absolute maximum ratings, input-current limits, and supply polarity in the Texas Instruments TLV2404 datasheet. A fuse, reverse-polarity controller, or discrete protection network may still be required where a misconnected battery could exceed those limits. Also verify that every alternative suffix preserves the same 14-pin PDIP footprint and required temperature range.
The 5.5 kHz gain-bandwidth product limits the useful closed-loop bandwidth even though the input and output stages are rail-to-rail. Calculate the required noise gain at the target frequency and check the expected phase margin. For an inverting amplifier, the feedback impedance seen by the inverting input can increase effective noise gain and reduce stability, so verify the complete resistor-capacitor network rather than relying only on the nominal signal gain.
Estimated: using a 16 V supply and 3.52 mA total quiescent current for four channels, the no-load supply dissipation is approximately 56.3 mW. Output-current dissipation must be added using the voltage dropped across each active amplifier. The PDIP package removes heat primarily through its leads, so place it where warm air can flow and avoid enclosing it in an insulating enclosure without a thermal path.
合規資訊
The TLV2404IN is a general-purpose operational amplifier rather than an automotive-qualified device. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status require confirmation for the exact ordering code.