TLV2404IN - 16V Quad 5.5kHz RRIO Op Amp | Texas Instruments
MPN: TLV2404IN ✓ Hoạt độngTLV2404IN Tóm tắt
An operational amplifier is an analog signal-processing IC that uses high open-loop gain to amplify the difference between two input voltages. A rail-to-rail input stage accepts common-mode voltages across most of the supply range, while a rail-to-rail output stage can swing close to either supply rail. Within the amplifier hierarchy, the TLV2404IN belongs to the micropower operational-amplifier class and supports applications such as sensor conditioning, battery-powered instrumentation, current measurement, filtering, and low-frequency control loops.
Key features include four amplifier channels in one package, a 5.5 kHz gain-bandwidth product, rail-to-rail inputs and outputs, reverse-battery protection, and an approximately 880 nA per-channel quiescent current. Reverse-battery protection is particularly useful in portable systems where a misconnected battery can place reverse voltage across the device. The slow 5.5 kHz bandwidth favors low-frequency precision and sensing functions rather than high-speed signal processing.
The TLV2404IN combines four rail-to-rail amplifiers with a micropower bias architecture. Its low quiescent current reduces supply drain in continuously powered equipment, while the wide common-mode input capability simplifies buffering of sensors whose operating range lies close to a supply rail. Because this is a general-purpose amplifier rather than a high-speed comparator, designers should account for its limited gain-bandwidth product when setting filter poles, closed-loop gain, and required settling behavior.
Typical applications include portable battery-powered monitors, industrial sensor interfaces, low-frequency active filters, current-sense amplifier signal chains, and general-purpose analog instrumentation. A four-channel implementation can reduce board area when several independent low-frequency signals require amplification, provided each channel's noise, offset, common-mode range, and stability requirements are compatible.
When designing around the TLV2404IN, check source and sink current capability at the chosen output voltage, place decoupling capacitors close to the supply pins, and confirm that each feedback network supports the intended operating frequency. Avoid treating reverse-battery protection as a substitute for correct battery polarity or for a dedicated fuse and protection network.
This product page consolidates the exact TLV2404IN device characteristics, family-level alternatives, application guidance, pin-package constraints, and practical design notes into an engineering-focused reference for evaluating the amplifier before PCB implementation.
Bộ thay thế dễ dàng lắp đặt cho TLV2404IN — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với TLV2404IN (cùng hình factor và footprint) — khác nhau ở Reverse-Battery Protection.
TLV2404CN
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →TLV2404IP
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
TLV2404INE4
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
TLV2404IN Tỷ lệ tối đa & tính chất điện
| Number of Amplifier Channels | 4 channels |
| Maximum Supply Voltage | 16 V |
| Gain-Bandwidth Product | 5.5 kHz |
| Điện áp yên tĩnh | Approximately 880 nA per channel |
| Input Common-Mode Range | Rail-to-rail |
| Output Swing | Rail-to-rail |
| Reverse-Battery Protection | Supported |
| Khoảng nhiệt độ hoạt động | -40 °C to 125 °C |
| Package Type | PDIP (N) |
| Số lượng chân | 14 pins |
| Kiểu lắp đặt | Through-hole |
| Product Type | Quad micropower rail-to-rail input/output operational amplifier |
| Operating Class | General-purpose amplifier |
| Primary Device Family | TLV2404 |
| Supplier Segment | Instrumentation and operational-amplifier applications |
Hướng dẫn cấu hình chân TLV2404IN pdip (n)
Cấu hình chân cho TLV2404IN (pdip (n) gói). Thành phần số hiệu này có chân đầu vào, đầu ra và nguồn cung cấp. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết cấu hình chân bù, bù trừ và chân kích hoạt. Hoàn hảo cho điều kiện tín hiệu và mạch khuếch đại.
Không có dữ liệu chân cụ thể sẵn có cho TLV2404IN.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
TLV2404IN phù hợp cho 6 Áp dụngs: Battery-Powered Sensor Conditioning, Industrial Process Measurement, Low-Frequency Active Filtering, Portable Medical Monitoring, Current Measurement Signal Chain, Data Acquisition Interface.
Battery-Powered Sensor Conditioning
The TLV2404IN suits low-frequency sensor-conditioning channels because four rail-to-rail amplifiers are integrated in one 14-pin PDIP package and quiescent current is approximately 880 nA per channel. A current sensor, thermistor, or resistive bridge can be conditioned with separate amplifier stages while keeping continuous supply drain low. The rail-to-rail input stage helps accept signals near the supply limits, and the rail-to-rail output stage provides more usable output range than a fixed-rail implementation. Because the gain-bandwidth product is 5.5 kHz, this device is intended for slow measurements rather than fast transients.
Được đề xuất
Industrial Process Measurement
The TLV2404IN can condition several low-frequency industrial process signals when the design requires a common quad-amplifier package and a 16 V maximum supply rating. Each channel may buffer a thermocouple interface, pressure-sensor signal, or scaled plant-control voltage. Rail-to-rail inputs and outputs improve headroom when operating from lower supply voltages, while approximately 880 nA per channel is valuable in remotely powered instrumentation. The 5.5 kHz bandwidth is adequate for slow process variables, but loop compensation and sensor-response requirements must be checked to ensure the resulting closed-loop bandwidth remains sufficient.
Được đề xuất
Low-Frequency Active Filtering
The TLV2404IN is appropriate for active filters and shaping networks operating below its 5.5 kHz gain-bandwidth product. Four channels can implement two cascaded second-order filters, a fourth-order low-pass or high-pass section, or several separate signal-conditioning stages. Rail-to-rail operation helps preserve signal amplitude in low-voltage systems, while the approximately 880 nA per-channel bias supports compact, low-power monitoring equipment. Component selection should account for closed-loop gain, noise gain, output loading, and the amplifier's phase-margin behavior rather than treating 5.5 kHz as a guaranteed usable filter cutoff.
Được đề xuất
Portable Medical Monitoring
The TLV2404IN can support low-frequency conditioning paths in portable monitoring equipment where four amplifier channels and low quiescent current simplify power budgeting. A bridge sensor, bio-sensor analog front end, or patient-monitoring transducer may use separate channels for buffering, gain, filtering, and output drive. The -40 °C to 125 °C rating provides a broad environmental range, while rail-to-rail inputs and outputs help use the available supply voltage efficiently. Medical-system designers must separately validate patient protection, isolation, leakage, electromagnetic compatibility, and applicable regulatory requirements for the finished instrument.
Được đề xuất
Current Measurement Signal Chain
The TLV2404IN is useful after a current-sense amplifier when the system requires additional filtering, level shifting, or output buffering across multiple channels. Its approximately 880 nA per-channel quiescent current minimizes overhead in portable or distributed power systems, and the 16 V maximum supply rating supports common industrial and automotive-style rails when the complete signal path meets the device limits. The rail-to-rail output can improve utilization of the output range. Applications needing faster transient capture or very low amplifier noise should compare the TLV2404's 5.5 kHz bandwidth against their measurement bandwidth.
Được đề xuất
Data Acquisition Interface
The TLV2404IN can provide buffering and channel conditioning ahead of a moderately slow data-acquisition system. Four independent channels may handle analog inputs from sensors, dividers, or level-shifting networks, while the 5.5 kHz gain-bandwidth product suits sampled measurements whose relevant signal content is low frequency. Rail-to-rail inputs help accommodate sensor outputs that approach the supply range, and the low quiescent current supports compact multi-channel acquisition equipment. The ADC, sampling rate, anti-alias filter, settling requirements, and input-source impedance must be evaluated together to verify the complete acquisition path.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho TLV2404IN — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | TLV2404CN | TLV2404IP | TLV2404INE4 |
|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | PDIP-14 (N) | PDIP-14 (N) | PDIP-14 (N) | PDIP-14 (N) |
| Number of Channels | 4 channels | 4 channels | 4 channels | 4 channels |
| Maximum Supply Voltage | 16 V | 16 V | 16 V | 16 V |
| Gain-Bandwidth Product | 5.5 kHz | 5.5 kHz | 5.5 kHz | 5.5 kHz |
| Input Common-Mode Range | Rail-to-rail | Rail-to-rail | Rail-to-rail | Rail-to-rail |
| Output Swing | Rail-to-rail | Rail-to-rail | Rail-to-rail | Rail-to-rail |
Bảo phân biệt quan trọng
- Four rail-to-rail amplifiers in one through-hole package (vsTLV2404IP)
- Low-power bias supports continuous instrumentation (vsTLV2404CN)
- Exact TLV2404IN ordering configuration (vsTLV2404INE4)
Ghi chú thiết kế
Route each amplifier's supply and ground connections directly to the nearest package pins, and place the supply-decoupling capacitor close to the device. For a four-channel package, separate analog input traces from output and supply paths to reduce coupling between channels. Keep feedback components close to the relevant amplifier inputs and outputs so parasitic capacitance does not destabilize the 5.5 kHz-gain-bandwidth device.
Do not treat reverse-battery protection as a complete battery-safety solution. Verify the exact protection conditions, absolute maximum ratings, input-current limits, and supply polarity in the Texas Instruments TLV2404 datasheet. A fuse, reverse-polarity controller, or discrete protection network may still be required where a misconnected battery could exceed those limits. Also verify that every alternative suffix preserves the same 14-pin PDIP footprint and required temperature range.
The 5.5 kHz gain-bandwidth product limits the useful closed-loop bandwidth even though the input and output stages are rail-to-rail. Calculate the required noise gain at the target frequency and check the expected phase margin. For an inverting amplifier, the feedback impedance seen by the inverting input can increase effective noise gain and reduce stability, so verify the complete resistor-capacitor network rather than relying only on the nominal signal gain.
Estimated: using a 16 V supply and 3.52 mA total quiescent current for four channels, the no-load supply dissipation is approximately 56.3 mW. Output-current dissipation must be added using the voltage dropped across each active amplifier. The PDIP package removes heat primarily through its leads, so place it where warm air can flow and avoid enclosing it in an insulating enclosure without a thermal path.
Thông tin tuân thủ
The TLV2404IN is a general-purpose operational amplifier rather than an automotive-qualified device. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status require confirmation for the exact ordering code.