TLV2404IN - 16V Quad 5.5kHz RRIO Op Amp | Texas Instruments
N.º de pieza: TLV2404IN ✓ ActivoTLV2404IN Descripción general
An operational amplifier is an analog signal-processing IC that uses high open-loop gain to amplify the difference between two input voltages. A rail-to-rail input stage accepts common-mode voltages across most of the supply range, while a rail-to-rail output stage can swing close to either supply rail. Within the amplifier hierarchy, the TLV2404IN belongs to the micropower operational-amplifier class and supports applications such as sensor conditioning, battery-powered instrumentation, current measurement, filtering, and low-frequency control loops.
Key features include four amplifier channels in one package, a 5.5 kHz gain-bandwidth product, rail-to-rail inputs and outputs, reverse-battery protection, and an approximately 880 nA per-channel quiescent current. Reverse-battery protection is particularly useful in portable systems where a misconnected battery can place reverse voltage across the device. The slow 5.5 kHz bandwidth favors low-frequency precision and sensing functions rather than high-speed signal processing.
The TLV2404IN combines four rail-to-rail amplifiers with a micropower bias architecture. Its low quiescent current reduces supply drain in continuously powered equipment, while the wide common-mode input capability simplifies buffering of sensors whose operating range lies close to a supply rail. Because this is a general-purpose amplifier rather than a high-speed comparator, designers should account for its limited gain-bandwidth product when setting filter poles, closed-loop gain, and required settling behavior.
Typical applications include portable battery-powered monitors, industrial sensor interfaces, low-frequency active filters, current-sense amplifier signal chains, and general-purpose analog instrumentation. A four-channel implementation can reduce board area when several independent low-frequency signals require amplification, provided each channel's noise, offset, common-mode range, and stability requirements are compatible.
When designing around the TLV2404IN, check source and sink current capability at the chosen output voltage, place decoupling capacitors close to the supply pins, and confirm that each feedback network supports the intended operating frequency. Avoid treating reverse-battery protection as a substitute for correct battery polarity or for a dedicated fuse and protection network.
This product page consolidates the exact TLV2404IN device characteristics, family-level alternatives, application guidance, pin-package constraints, and practical design notes into an engineering-focused reference for evaluating the amplifier before PCB implementation.
Alternativas directas para TLV2404IN — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
Variantes de esta serie
Modelos de la misma serie compatibles directamente con TLV2404IN (mismo factor de forma y huella) — difiere en Reverse-Battery Protection.
TLV2404CN
✅ Sustitución directa ⚠️ Especificaciones sin verificarConsulte el precio
Ver hoja de datos →TLV2404IP
✅ Sustitución directa ⚠️ Especificaciones sin verificar📋 Alternativa de referencia (no en el catálogo)
TLV2404INE4
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
TLV2404IN Valores máximos y características eléctricas
| Number of Amplifier Channels | 4 channels |
| Maximum Supply Voltage | 16 V |
| Gain-Bandwidth Product | 5.5 kHz |
| Corriente en reposo | Approximately 880 nA per channel |
| Input Common-Mode Range | Rail-to-rail |
| Output Swing | Rail-to-rail |
| Reverse-Battery Protection | Supported |
| Rango de temperatura de funcionamiento | -40 °C to 125 °C |
| Package Type | PDIP (N) |
| Número de pines | 14 pins |
| Tipo de montaje | Through-hole |
| Product Type | Quad micropower rail-to-rail input/output operational amplifier |
| Operating Class | General-purpose amplifier |
| Primary Device Family | TLV2404 |
| Supplier Segment | Instrumentation and operational-amplifier applications |
Guía de configuración de pines de TLV2404IN pdip (n)
Configuración de pines para TLV2404IN (encapsulado pdip (n)). Este componente analógico presenta pines de entrada, salida y alimentación. Consulte la hoja de datos del fabricante para conocer las configuraciones de los pines de ajuste de offset, compensación y habilitación. Ideal para circuitos de acondicionamiento de señal y amplificadores.
No hay datos detallados de patillaje disponibles para TLV2404IN.
Consulte la hoja de datos para ver la configuración completa de patillas.
Aplicaciones típicas
TLV2404IN es adecuado para 6 aplicacións: Battery-Powered Sensor Conditioning, Industrial Process Measurement, Low-Frequency Active Filtering, Portable Medical Monitoring, Current Measurement Signal Chain, Data Acquisition Interface.
Battery-Powered Sensor Conditioning
The TLV2404IN suits low-frequency sensor-conditioning channels because four rail-to-rail amplifiers are integrated in one 14-pin PDIP package and quiescent current is approximately 880 nA per channel. A current sensor, thermistor, or resistive bridge can be conditioned with separate amplifier stages while keeping continuous supply drain low. The rail-to-rail input stage helps accept signals near the supply limits, and the rail-to-rail output stage provides more usable output range than a fixed-rail implementation. Because the gain-bandwidth product is 5.5 kHz, this device is intended for slow measurements rather than fast transients.
Recomendado
Industrial Process Measurement
The TLV2404IN can condition several low-frequency industrial process signals when the design requires a common quad-amplifier package and a 16 V maximum supply rating. Each channel may buffer a thermocouple interface, pressure-sensor signal, or scaled plant-control voltage. Rail-to-rail inputs and outputs improve headroom when operating from lower supply voltages, while approximately 880 nA per channel is valuable in remotely powered instrumentation. The 5.5 kHz bandwidth is adequate for slow process variables, but loop compensation and sensor-response requirements must be checked to ensure the resulting closed-loop bandwidth remains sufficient.
Recomendado
Low-Frequency Active Filtering
The TLV2404IN is appropriate for active filters and shaping networks operating below its 5.5 kHz gain-bandwidth product. Four channels can implement two cascaded second-order filters, a fourth-order low-pass or high-pass section, or several separate signal-conditioning stages. Rail-to-rail operation helps preserve signal amplitude in low-voltage systems, while the approximately 880 nA per-channel bias supports compact, low-power monitoring equipment. Component selection should account for closed-loop gain, noise gain, output loading, and the amplifier's phase-margin behavior rather than treating 5.5 kHz as a guaranteed usable filter cutoff.
Recomendado
Portable Medical Monitoring
The TLV2404IN can support low-frequency conditioning paths in portable monitoring equipment where four amplifier channels and low quiescent current simplify power budgeting. A bridge sensor, bio-sensor analog front end, or patient-monitoring transducer may use separate channels for buffering, gain, filtering, and output drive. The -40 °C to 125 °C rating provides a broad environmental range, while rail-to-rail inputs and outputs help use the available supply voltage efficiently. Medical-system designers must separately validate patient protection, isolation, leakage, electromagnetic compatibility, and applicable regulatory requirements for the finished instrument.
Recomendado
Current Measurement Signal Chain
The TLV2404IN is useful after a current-sense amplifier when the system requires additional filtering, level shifting, or output buffering across multiple channels. Its approximately 880 nA per-channel quiescent current minimizes overhead in portable or distributed power systems, and the 16 V maximum supply rating supports common industrial and automotive-style rails when the complete signal path meets the device limits. The rail-to-rail output can improve utilization of the output range. Applications needing faster transient capture or very low amplifier noise should compare the TLV2404's 5.5 kHz bandwidth against their measurement bandwidth.
Recomendado
Data Acquisition Interface
The TLV2404IN can provide buffering and channel conditioning ahead of a moderately slow data-acquisition system. Four independent channels may handle analog inputs from sensors, dividers, or level-shifting networks, while the 5.5 kHz gain-bandwidth product suits sampled measurements whose relevant signal content is low frequency. Rail-to-rail inputs help accommodate sensor outputs that approach the supply range, and the low quiescent current supports compact multi-channel acquisition equipment. The ADC, sampling rate, anti-alias filter, settling requirements, and input-source impedance must be evaluated together to verify the complete acquisition path.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para TLV2404IN — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto | TLV2404CN | TLV2404IP | TLV2404INE4 |
|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | PDIP-14 (N) | PDIP-14 (N) | PDIP-14 (N) | PDIP-14 (N) |
| Number of Channels | 4 channels | 4 channels | 4 channels | 4 channels |
| Maximum Supply Voltage | 16 V | 16 V | 16 V | 16 V |
| Gain-Bandwidth Product | 5.5 kHz | 5.5 kHz | 5.5 kHz | 5.5 kHz |
| Input Common-Mode Range | Rail-to-rail | Rail-to-rail | Rail-to-rail | Rail-to-rail |
| Output Swing | Rail-to-rail | Rail-to-rail | Rail-to-rail | Rail-to-rail |
Diferenciadores clave
- Four rail-to-rail amplifiers in one through-hole package (frente a TLV2404IP)
- Low-power bias supports continuous instrumentation (frente a TLV2404CN)
- Exact TLV2404IN ordering configuration (frente a TLV2404INE4)
Notas de diseño
Route each amplifier's supply and ground connections directly to the nearest package pins, and place the supply-decoupling capacitor close to the device. For a four-channel package, separate analog input traces from output and supply paths to reduce coupling between channels. Keep feedback components close to the relevant amplifier inputs and outputs so parasitic capacitance does not destabilize the 5.5 kHz-gain-bandwidth device.
Do not treat reverse-battery protection as a complete battery-safety solution. Verify the exact protection conditions, absolute maximum ratings, input-current limits, and supply polarity in the Texas Instruments TLV2404 datasheet. A fuse, reverse-polarity controller, or discrete protection network may still be required where a misconnected battery could exceed those limits. Also verify that every alternative suffix preserves the same 14-pin PDIP footprint and required temperature range.
The 5.5 kHz gain-bandwidth product limits the useful closed-loop bandwidth even though the input and output stages are rail-to-rail. Calculate the required noise gain at the target frequency and check the expected phase margin. For an inverting amplifier, the feedback impedance seen by the inverting input can increase effective noise gain and reduce stability, so verify the complete resistor-capacitor network rather than relying only on the nominal signal gain.
Estimated: using a 16 V supply and 3.52 mA total quiescent current for four channels, the no-load supply dissipation is approximately 56.3 mW. Output-current dissipation must be added using the voltage dropped across each active amplifier. The PDIP package removes heat primarily through its leads, so place it where warm air can flow and avoid enclosing it in an insulating enclosure without a thermal path.
Información de cumplimiento
The TLV2404IN is a general-purpose operational amplifier rather than an automotive-qualified device. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status require confirmation for the exact ordering code.