TUSB1105RGTR - USB 2.0 Transceiver | Texas Instruments
MPN: TUSB1105RGTR ✓ 啟用中TUSB1105RGTR 概覽
A universal serial bus transceiver is an interface circuit that converts logic-level data into USB-compatible differential signaling and converts received differential signals back into digital logic. The TUSB1105 belongs to the USB interface IC hierarchy, where USB transceivers connect a host, peripheral, or embedded controller to a USB connector while providing the physical-layer signaling required by USB 2.0 devices.
The principal features include compliance with the Universal Serial Bus Specification Revision 2.0, full-speed operation at 12 Mbit/s, low-speed operation at 1.5 Mbit/s, and a half-duplex 1/1 transceiver configuration. Its 16-VQFN package is 3 mm by 3 mm, making the device suitable for space-constrained portable, industrial, and embedded USB equipment. The exposed-pad package also supports compact PCB layouts when its land pattern and thermal design are implemented correctly.
The TUSB1105 is intended for external USB connectivity rather than direct USB data signaling across a long cable or printed circuit board. Its transmit and receive path handles the USB differential interface, while the connected USB controller or embedded processor performs protocol handling. This division keeps low-level signaling separate from the higher layers of USB enumeration, descriptors, classes, and transfers.
Typical uses include USB-to-serial adapters, portable test and measurement equipment, industrial control panels, data-collection terminals, and accessory controllers that need a compact full-speed or low-speed USB interface. For designs that expose a USB Type-A or USB Type-B receptacle, the transceiver should be paired with the appropriate connector, protection network, routing geometry, and controller-specific interface requirements.
PCB implementation requires careful treatment of the differential USB pair, the exposed ground pad, and the short connection between the transceiver and connector. Maintain a continuous ground reference, route D+ and D+ together and D− and D− together, and minimize stubs and unnecessary vias. Confirm the final layout against the pin-description and layout guidance in the manufacturer datasheet.
This page combines the confirmed USB 2.0 speed ratings, package information, drop-in replacement findings, interface-selection guidance, and practical PCB considerations into a compact engineering reference for USB transceiver designs.
直接替換替代品,適用於 TUSB1105RGTR — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: TUSB1105RGTR (相同外形與佔位) — 差異在於 Package, Product Type.
TUSB1106RTZR
✅ 直接替換聯絡詢價
查看資料表 →TUSB1105RTZR
✅ 直接替換📋 參考替代品(不在目錄中)
TUSB1105RGTR 規格
| Product Type | Universal Serial Bus transceiver |
| USB Specification Compliance | Universal Serial Bus Specification Revision 2.0 |
| Transceiver Configuration | 1/1 half-duplex transceiver |
| Full-Speed Data Rate | 12 Mbit/s |
| Low-Speed Data Rate | 1.5 Mbit/s |
| Number of Channels | 1 channel |
| 封裝 | 16-pin VQFN |
| Package Dimensions | 3 mm x 3 mm |
| 安裝類型 | Surface mount |
TUSB1105RGTR 3 mm x 3 mm 腳位配置指南
TUSB1105RGTR(3 mm x 3 mm 封裝)的腳位配置。 腳位編號、功能與連接圖定義於製造商資料手冊中。請參閱該手冊以取得確切的封裝尺寸與焊接指引。
無詳細腳位定義資料: TUSB1105RGTR.
請參閱 資料表 以查看完整腳位配置。
典型應用
TUSB1105RGTR 適用於 6 應用s: USB-to-Serial Data Collection, Portable Test and Measurement Equipment, Industrial Control Interface, USB Accessory and Peripheral Controller, Security and Monitoring Accessory, USB-to-Field Service Adapter.
USB-to-Serial Data Collection
TUSB1105RGTR fits compact data-collection equipment that exposes a USB 2.0 control interface to a host computer. Its confirmed full-speed rate of 12 Mbit/s is appropriate for configuration transfers, status reporting, and moderate command traffic, while low-speed support at 1.5 Mbit/s broadens peripheral compatibility. Place the transceiver between the embedded controller and USB connector, route D+ and D− as a short differential pair, and confirm the controller’s required signal polarity. The 3 mm by 3 mm VQFN package also helps reduce board area in handheld or portable instruments.
推薦
Portable Test and Measurement Equipment
TUSB1105RGTR can provide the physical USB interface in portable measurement products that exchange commands and sampled results with a computer. USB full-speed operation at 12 Mbit/s is useful for instrument control and moderate data movement, while the 16-pin 3 mm by 3 mm VQFN package supports dense front-panel or internal layouts. The USB transceiver should be positioned near the connector, with the differential pair kept over a continuous ground plane. Engineers should also verify the transceiver’s polarity and signal mapping against the test instrument’s embedded controller.
推薦
Industrial Control Interface
TUSB1105RGTR is appropriate for industrial control modules that use a USB 2.0 full-speed connection for configuration, diagnostics, and firmware-related services. Its 12 Mbit/s full-speed capability provides more bandwidth than low-speed USB while remaining focused on control traffic rather than high-speed data streaming. In an industrial enclosure, keep the USB path away from motor switching stages and noisy power converters, and maintain short differential routing from the transceiver to the connector. Confirm grounding and signal polarity across controller, transceiver, and protection-device choices.
推薦
USB Accessory and Peripheral Controller
TUSB1105RGTR can interface a dedicated accessory controller to a USB host through a full-speed or low-speed USB connection. A single 1/1 transceiver path is suitable for compact peripheral designs that do not require simultaneous independent transmit and receive channels. The controller handles USB protocol tasks while the TUSB1105 handles differential transmit and receive signaling. Layout should prioritize a short connector-to-transceiver path, a solid ground reference, and clean separation from switching supplies or digital clocks that could degrade USB signal integrity.
推薦
Security and Monitoring Accessory
TUSB1105RGTR is suitable for monitoring accessories that connect to a host system for setup, status, and event transfer over USB full-speed. The confirmed 12 Mbit/s rate supports typical control traffic, and the compact VQFN package preserves board space beside sensors or communication hardware. Position the transceiver near the external USB connector, avoid routing the differential pair beneath switching regulators, and follow the exposed-pad and via recommendations in the manufacturer datasheet. Signal polarity and controller mapping must be verified before production.
推薦
USB-to-Field Service Adapter
TUSB1105RGTR can serve as the USB interface in a field-service adapter that exchanges diagnostic commands and configuration files with a laptop or service tablet. Full-speed operation at 12 Mbit/s is suitable for this transfer profile, and low-speed support at 1.5 Mbit/s allows broader compatibility with basic USB peripherals. The device’s 3 mm by 3 mm package supports compact adapters. Route the USB differential pair directly from the transceiver to the connector, provide a continuous ground plane, and verify connector orientation, signal polarity, and exposed-pad soldering in the assembly process.
推薦
推薦產品摘要
工程參考資料,適用於 TUSB1105RGTR — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | TUSB1106RTZR | TUSB1105RTZR |
|---|---|---|---|
| Package | 16-pin VQFN, 3 mm x 3 mm | 16-pin VQFN | 16-pin VQFN |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Product Type | Universal Serial Bus transceiver | USB transceiver | USB transceiver |
| Mounting Type | Surface mount | Surface mount | Surface mount |
主要差異化特點
- Compact single-channel USB interface (對比TUSB1106RTZR)
- Confirmed USB full-speed and low-speed support (對比TUSB1105RTZR)
- Single-rail interface placement in compact products (對比TUSB1106RTZR)
設計說明
Route D+ and D− as a short, continuously referenced differential pair from TUSB1105RGTR to the USB connector. Minimize stubs, avoid unnecessary vias, and keep the pair over an uninterrupted ground plane. Place the transceiver close to the connector and compare the final geometry with the USB layout guidance in the Texas Instruments manufacturer datasheet.
Implement the exposed-pad land pattern, thermal vias, and solder-mask design specified for the 16-VQFN package. The exposed pad should connect to the appropriate ground plane without creating return-path discontinuities. Follow the manufacturer’s land-pattern dimensions and reflow profile rather than substituting a generic QFN footprint.
Keep the USB channel away from noisy switching regulators, high-current motor drivers, and unrelated high-speed clocks. Maintain consistent impedance along the differential pair and use only short connections between the transceiver and its external protection or filtering components. Validate signal integrity with the connector, protection-device capacitance, and controller configuration used in the finished product.
合規資訊
Compliance attributes were not confirmed in the manufacturer product excerpts or verified distributor results. Review the current Texas Instruments product information and applicable material declarations before release.