TUSB1105RGTR - USB 2.0 Transceiver | Texas Instruments
部品番号: TUSB1105RGTR ✓ 生産中TUSB1105RGTR 概要
A universal serial bus transceiver is an interface circuit that converts logic-level data into USB-compatible differential signaling and converts received differential signals back into digital logic. The TUSB1105 belongs to the USB interface IC hierarchy, where USB transceivers connect a host, peripheral, or embedded controller to a USB connector while providing the physical-layer signaling required by USB 2.0 devices.
The principal features include compliance with the Universal Serial Bus Specification Revision 2.0, full-speed operation at 12 Mbit/s, low-speed operation at 1.5 Mbit/s, and a half-duplex 1/1 transceiver configuration. Its 16-VQFN package is 3 mm by 3 mm, making the device suitable for space-constrained portable, industrial, and embedded USB equipment. The exposed-pad package also supports compact PCB layouts when its land pattern and thermal design are implemented correctly.
The TUSB1105 is intended for external USB connectivity rather than direct USB data signaling across a long cable or printed circuit board. Its transmit and receive path handles the USB differential interface, while the connected USB controller or embedded processor performs protocol handling. This division keeps low-level signaling separate from the higher layers of USB enumeration, descriptors, classes, and transfers.
Typical uses include USB-to-serial adapters, portable test and measurement equipment, industrial control panels, data-collection terminals, and accessory controllers that need a compact full-speed or low-speed USB interface. For designs that expose a USB Type-A or USB Type-B receptacle, the transceiver should be paired with the appropriate connector, protection network, routing geometry, and controller-specific interface requirements.
PCB implementation requires careful treatment of the differential USB pair, the exposed ground pad, and the short connection between the transceiver and connector. Maintain a continuous ground reference, route D+ and D+ together and D− and D− together, and minimize stubs and unnecessary vias. Confirm the final layout against the pin-description and layout guidance in the manufacturer datasheet.
This page combines the confirmed USB 2.0 speed ratings, package information, drop-in replacement findings, interface-selection guidance, and practical PCB considerations into a compact engineering reference for USB transceiver designs.
ドロップイン代替品: TUSB1105RGTR — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: TUSB1105RGTR (同一形状・フットプリント) — 相違点: Package, Product Type.
TUSB1106RTZR
✅ ドロップイン価格はお問い合わせください
データシートを見る →TUSB1105RTZR
✅ ドロップイン📋 参考代替品(カタログ未掲載)
TUSB1105RGTR 仕様
| Product Type | Universal Serial Bus transceiver |
| USB Specification Compliance | Universal Serial Bus Specification Revision 2.0 |
| Transceiver Configuration | 1/1 half-duplex transceiver |
| Full-Speed Data Rate | 12 Mbit/s |
| Low-Speed Data Rate | 1.5 Mbit/s |
| Number of Channels | 1 channel |
| パッケージ | 16-pin VQFN |
| Package Dimensions | 3 mm x 3 mm |
| 実装タイプ | Surface mount |
TUSB1105RGTR 3 mm x 3 mm ピン配置ガイド
TUSB1105RGTR (3 mm x 3 mm パッケージ) のピン配置。 ピン番号、機能、接続図はメーカーのデータシートで定義されています。正確なフットプリントとはんだ付けのガイドラインについては、データシートを参照してください。
詳細なピン配置データはありません: TUSB1105RGTR.
詳細は データシート をご参照ください。
主な用途
TUSB1105RGTR の用途: 6 件s: USB-to-Serial Data Collection, Portable Test and Measurement Equipment, Industrial Control Interface, USB Accessory and Peripheral Controller, Security and Monitoring Accessory, USB-to-Field Service Adapter.
USB-to-Serial Data Collection
TUSB1105RGTR fits compact data-collection equipment that exposes a USB 2.0 control interface to a host computer. Its confirmed full-speed rate of 12 Mbit/s is appropriate for configuration transfers, status reporting, and moderate command traffic, while low-speed support at 1.5 Mbit/s broadens peripheral compatibility. Place the transceiver between the embedded controller and USB connector, route D+ and D− as a short differential pair, and confirm the controller’s required signal polarity. The 3 mm by 3 mm VQFN package also helps reduce board area in handheld or portable instruments.
おすすめ
Portable Test and Measurement Equipment
TUSB1105RGTR can provide the physical USB interface in portable measurement products that exchange commands and sampled results with a computer. USB full-speed operation at 12 Mbit/s is useful for instrument control and moderate data movement, while the 16-pin 3 mm by 3 mm VQFN package supports dense front-panel or internal layouts. The USB transceiver should be positioned near the connector, with the differential pair kept over a continuous ground plane. Engineers should also verify the transceiver’s polarity and signal mapping against the test instrument’s embedded controller.
おすすめ
Industrial Control Interface
TUSB1105RGTR is appropriate for industrial control modules that use a USB 2.0 full-speed connection for configuration, diagnostics, and firmware-related services. Its 12 Mbit/s full-speed capability provides more bandwidth than low-speed USB while remaining focused on control traffic rather than high-speed data streaming. In an industrial enclosure, keep the USB path away from motor switching stages and noisy power converters, and maintain short differential routing from the transceiver to the connector. Confirm grounding and signal polarity across controller, transceiver, and protection-device choices.
おすすめ
USB Accessory and Peripheral Controller
TUSB1105RGTR can interface a dedicated accessory controller to a USB host through a full-speed or low-speed USB connection. A single 1/1 transceiver path is suitable for compact peripheral designs that do not require simultaneous independent transmit and receive channels. The controller handles USB protocol tasks while the TUSB1105 handles differential transmit and receive signaling. Layout should prioritize a short connector-to-transceiver path, a solid ground reference, and clean separation from switching supplies or digital clocks that could degrade USB signal integrity.
おすすめ
Security and Monitoring Accessory
TUSB1105RGTR is suitable for monitoring accessories that connect to a host system for setup, status, and event transfer over USB full-speed. The confirmed 12 Mbit/s rate supports typical control traffic, and the compact VQFN package preserves board space beside sensors or communication hardware. Position the transceiver near the external USB connector, avoid routing the differential pair beneath switching regulators, and follow the exposed-pad and via recommendations in the manufacturer datasheet. Signal polarity and controller mapping must be verified before production.
おすすめ
USB-to-Field Service Adapter
TUSB1105RGTR can serve as the USB interface in a field-service adapter that exchanges diagnostic commands and configuration files with a laptop or service tablet. Full-speed operation at 12 Mbit/s is suitable for this transfer profile, and low-speed support at 1.5 Mbit/s allows broader compatibility with basic USB peripherals. The device’s 3 mm by 3 mm package supports compact adapters. Route the USB differential pair directly from the transceiver to the connector, provide a continuous ground plane, and verify connector orientation, signal polarity, and exposed-pad soldering in the assembly process.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: TUSB1105RGTR — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | TUSB1106RTZR | TUSB1105RTZR |
|---|---|---|---|
| Package | 16-pin VQFN, 3 mm x 3 mm | 16-pin VQFN | 16-pin VQFN |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Product Type | Universal Serial Bus transceiver | USB transceiver | USB transceiver |
| Mounting Type | Surface mount | Surface mount | Surface mount |
主な差別化要因
- Compact single-channel USB interface (vs TUSB1106RTZR)
- Confirmed USB full-speed and low-speed support (vs TUSB1105RTZR)
- Single-rail interface placement in compact products (vs TUSB1106RTZR)
設計ノート
Route D+ and D− as a short, continuously referenced differential pair from TUSB1105RGTR to the USB connector. Minimize stubs, avoid unnecessary vias, and keep the pair over an uninterrupted ground plane. Place the transceiver close to the connector and compare the final geometry with the USB layout guidance in the Texas Instruments manufacturer datasheet.
Implement the exposed-pad land pattern, thermal vias, and solder-mask design specified for the 16-VQFN package. The exposed pad should connect to the appropriate ground plane without creating return-path discontinuities. Follow the manufacturer’s land-pattern dimensions and reflow profile rather than substituting a generic QFN footprint.
Keep the USB channel away from noisy switching regulators, high-current motor drivers, and unrelated high-speed clocks. Maintain consistent impedance along the differential pair and use only short connections between the transceiver and its external protection or filtering components. Validate signal integrity with the connector, protection-device capacitance, and controller configuration used in the finished product.
コンプライアンス情報
Compliance attributes were not confirmed in the manufacturer product excerpts or verified distributor results. Review the current Texas Instruments product information and applicable material declarations before release.