XC2C64A-7VQG44C - 64-Macrocell 1.8V CPLD | Xilinx
MPN: XC2C64A-7VQG44C ✓ 啟用中XC2C64A-7VQG44C 概覽
A CPLD, or complex programmable logic device, is a user-programmable semiconductor that combines multiple logic functions into one reconfigurable device. Its hierarchy places it within programmable logic alongside FPGA and CPLD technologies, where it is especially useful for compact glue logic, protocol conversion, bus arbitration, and interface control. CoolRunner-II combines nonvolatile configuration storage with low-power operation, allowing the implemented circuit to retain its logic after power is removed.
Key features include 64 macrocells distributed across 4 function blocks, up to 1,500 usable gates, and a maximum system frequency of 159 MHz. The -7 speed designation places this part in the 159 MHz performance class, while the G package code identifies the 44-pin VTQFP configuration. Input/output performance can reach a 4.6 ns pin-to-pin logic delay, and the architecture is optimized for systems operating from a 1.8 V supply.
The CoolRunner-II architecture uses Xilinx RealDigital technology in a 0.18 µm CMOS Flash process. Flash-based configuration supports nonvolatile programmed logic, while the low-power design targets both high-performance and battery-operated equipment. The programmable macrocell structure provides a practical capacity for multi-function logic without the resource overhead of a much larger FPGA.
Typical uses include communication-equipment interface logic, battery-powered portable systems, bus control, protocol bridging, embedded control, and general-purpose glue logic. The 33 user I/O pins are suitable for connecting the CPLD to external memory, processors, converters, and peripheral devices when the board's electrical requirements match the selected I/O standards.
Designers should review the DS311 device pin table before assigning every signal, especially configuration, power, ground, and I/O pins. Validate signal timing at the intended system frequency, apply the manufacturer's recommended bypass capacitors, and observe the package-specific keep-out and thermal-pad guidance. For an existing XC2C64 design, the AMD XCN05017 notice identifies XC2C64A as the enhanced pin-for-pin replacement for the original XC2C64.
This product record combines the DS311 family specifications with practical device-selection, timing, package, and migration guidance. It also distinguishes same-package speed-grade alternatives from larger-package CoolRunner-II variants, helping engineers preserve PCB compatibility while evaluating performance, temperature grade, and lifecycle constraints.
直接替換替代品,適用於 XC2C64A-7VQG44C — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: XC2C64A-7VQG44C (相同外形與佔位) — 差異在於 Device Type, Process Technology, RoHS Status, Package Dimensions, Quiescent Current.
XC2C64A-7VQG44I
✅ 直接替換聯絡詢價
查看資料表 →XC2C64A-5VQG44C
✅ 直接替換聯絡詢價
查看資料表 →XC2C64A-5VQ44C
✅ 直接替換聯絡詢價
查看資料表 →XC2C64A-5VQ44I
✅ 直接替換📋 參考替代品(不在目錄中)
XC2C64A-7VQG100C
✅ 直接替換📋 參考替代品(不在目錄中)
XC2C64A-7VQG44C 最大額定值與電氣特性
| Device Type | CoolRunner-II complex programmable logic device (CPLD) |
| Macrocells | 64 macrocells |
| Logic Blocks | 4 function blocks |
| Usable Gates | 1,500 gates |
| Maximum System Frequency | 159 MHz |
| Maximum Pin-to-Pin Logic Delay | 4.6 ns |
| 靜態電流 | 15 µA minimum |
| Process Technology | 0.18 µm CMOS Flash |
| Core Supply Voltage | 1.8 V |
| User I/O Count | 33 pins |
| Total Pin Count | 44 pins |
| 封裝 | 44-pin VTQFP, 10 mm × 10 mm |
| 安裝類型 | Surface mount |
| Configuration Memory | Flash, nonvolatile |
| Hot-Swap Support | Supported |
| Logic Architecture | Xilinx RealDigital technology |
| Application Class | High-performance and low-power programmable logic |
| RoHS 狀態 | Compliant |
XC2C64A-7VQG44C 44-pin vtqfp, 10 mm × 10 mm 腳位配置指南
XC2C64A-7VQG44C(44-pin vtqfp, 10 mm × 10 mm 封裝)的腳位配置。 此數位 IC 包含 GPIO、通訊介面(UART、SPI、I2C)與電源腳位。替代腳位功能與配置選項請參閱製造商資料表。對嵌入式系統設計與 PCB 佈局至關重要。
無詳細腳位定義資料: XC2C64A-7VQG44C.
請參閱 資料表 以查看完整腳位配置。
典型應用
XC2C64A-7VQG44C 適用於 6 應用s: Communication Equipment Interface Control, Battery-Powered Portable Logic, Protocol Conversion and Bus Arbitration, Embedded System Glue Logic, Hot-Swap Backplane Control, Industrial Control and Data Acquisition.
Communication Equipment Interface Control
The XC2C64A-7VQG44C fits communication-equipment control and interface logic where a compact nonvolatile CPLD provides faster timing than a basic fuse-logic device. Its 64 macrocells and 4 logic blocks can consolidate address decoding, command sequencing, status multiplexing, and programmable bus control. The -7 grade supports up to 159 MHz, giving designers additional timing margin in interfaces operating near the family limit. A 1.8 V core and Flash configuration also suit low-voltage communication boards requiring retained logic after power cycling. Before implementation, verify each external interface against DS311 timing tables and the pin-specific I/O requirements.
推薦
Battery-Powered Portable Logic
The XC2C64A-7VQG44C is suitable for battery-powered portable equipment because it combines Flash-based configuration with a low-power 1.8 V core architecture. Flash retention removes configuration reload time and allows compact control logic to operate without an external boot controller. The family documentation reports quiescent current as low as 15 µA, making low static consumption useful in sleep-oriented products. Designers can use the 64 macrocells for power-state sequencing, button handling, display control, and peripheral gating rather than implementing these functions in discrete logic. Actual battery life still depends on I/O activity, external pull states, and the selected system sleep strategy.
推薦
Protocol Conversion and Bus Arbitration
The XC2C64A-7VQG44C can implement protocol converters, bus arbiters, and asynchronous interface controllers when deterministic combinational and registered logic is needed. Its four logic blocks provide a practical partition for separate interface channels, while the -7 grade offers a maximum system frequency of 159 MHz. Flash configuration permits field-programmable logic changes without adding volatile configuration RAM. The 33 user I/O pins can connect processors, transceivers, memories, and peripheral devices, provided each interface conforms to its electrical standard. Use DS311 pin descriptions and timing tables to map bidirectional I/O behavior and avoid assigning unsupported dedicated functions.
推薦
Embedded System Glue Logic
XC2C64A-7VQG44C works well for embedded glue logic that connects processors, converters, sensors, and discrete interface devices. Typical assignments include chip selects, interrupt routing, reset sequencing, latch controls, and peripheral multiplexing. The 1,500 usable gates and 64 macrocells are sufficient for consolidating several small functions without moving to a larger FPGA. Its nonvolatile Flash configuration also reduces board space and controller overhead compared with a discrete logic plus external-programmed configuration approach. The 10 mm by 10 mm package keeps placement compact, while the -7 grade provides timing flexibility for moderately fast control paths. Validate worst-case timing and I/O loading during schematic review.
推薦
Hot-Swap Backplane Control
The XC2C64A-7VQG44C supports hot-swap operation, making it relevant to backplane modules that require controlled insertion and board-level state management. Its CPLD resources can coordinate power-enable requests, configuration status, reset sequencing, and fault reporting while avoiding a large processor on every plug-in card. The nonvolatile Flash configuration retains the logic configuration across power cycles, and the 44-pin package leaves a relatively compact footprint for space-constrained modules. Designers should follow DS311 hot-swap electrical conditions and ensure I/O states remain safe during insertion and removal. Board-level sequencing, isolation, and connector behavior must be designed as one complete system.
推薦
Industrial Control and Data Acquisition
The XC2C64A-7VQG44C can serve as the central logic device in industrial control and data-acquisition modules that require deterministic behavior, flexible I/O, and nonvolatile configuration. It can implement sensor multiplexing, command decoding, timing generation, data capture control, and machine-state logic within 64 macrocells. The -7 speed class supports interfaces approaching 159 MHz, while the 1.8 V core is compatible with modern low-voltage mixed-signal systems. For production equipment, choose the variant matching the required ambient-temperature range and verify system timing, I/O standards, and power sequencing against the manufacturer documentation. XC2C64A-7VQG44I is the relevant same-package choice when industrial temperature coverage is required.
推薦
推薦產品摘要
工程參考資料,適用於 XC2C64A-7VQG44C — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | XC2C64A-7VQG44I | XC2C64A-5VQG44C | XC2C64A-5VQ44C | XC2C64A-5VQ44I |
|---|---|---|---|---|---|
| Package | 44-pin VTQFP | 44-pin VTQFP | 44-pin VTQFP | 44-pin VTQFP | 44-pin VTQFP |
| Brand | Xilinx | Xilinx | Xilinx | Xilinx | Xilinx |
| Speed Grade | -7 | -7 | -5 | -5 | -5 |
| Temperature Classification | Commercial | Industrial | Commercial | Commercial | Industrial |
| Macrocells | 64 macrocells | 64 macrocells | 64 macrocells | 64 macrocells | 64 macrocells |
| Logic Blocks | 4 function blocks | 4 function blocks | 4 function blocks | 4 function blocks | 4 function blocks |
| Usable Gates | 1,500 gates | 1,500 gates | 1,500 gates | 1,500 gates | 1,500 gates |
| Core Supply Voltage | 1.8 V | 1.8 V | 1.8 V | 1.8 V | 1.8 V |
| Process Technology | 0.18 µm CMOS Flash | 0.18 µm CMOS Flash | 0.18 µm CMOS Flash | 0.18 µm CMOS Flash | 0.18 µm CMOS Flash |
| User I/O Count | 33 pins | 33 pins | 33 pins | 33 pins | 33 pins |
| Hot-Swap Support | Supported | Supported | Supported | Supported | Supported |
主要差異化特點
- Higher timing class than the -5 speed-grade alternatives (對比XC2C64A-5VQG44C)
- Commercial-temperature option preserves the -7 performance class (對比XC2C64A-7VQG44I)
- Same logic capacity with a smaller package than larger XC2C64A options (對比XC2C64A-7QFG48C)
- Manufacturer-confirmed migration path from the original XC2C64 (對比XC2C64A-7VQG100C)
設計說明
Route the 44-pin VTQFP footprint strictly from the DS311 package drawing, paying particular attention to pin-1 orientation, exposed thermal considerations, and the distinction between user I/O and dedicated configuration pins. Place the programmable device where its 10 mm by 10 mm package does not interfere with connector or heat-sink access. If migrating from a larger-package XC2C64A, do not reuse the old land pattern even though the internal device family is the same.
Validate every synchronous interface at the target clock rate using the -7 grade timing limits in DS311 rather than relying only on the nominal 159 MHz maximum. Include board skew, output loading, input thresholds, and external transceiver delays in the timing budget. The 4.6 ns pin-to-pin logic-delay figure describes the device path, not total board timing, so source-synchronous and system-level paths require separate analysis.
Follow the manufacturer recommendations for 1.8 V core decoupling and connect every specified power and ground pin. Keep the decoupling network close to the package and minimize loop area between each capacitor and its device pin. Evaluate active current from the implemented logic and I/O load rather than using the 15 µA quiescent figure as a system-power estimate. Confirm voltage tolerance and sequencing at the board level before enabling hot-swap operation.
Do not treat speed-grade, package, and temperature-grade suffixes as interchangeable. XC2C64A-5VQG44C preserves the 44-pin footprint but does not preserve the -7 timing class, while XC2C64A-7VQG44I changes the temperature classification. Also avoid using larger 48-, 56-, or 100-pin variants as board-level drop-ins. For migration from the original XC2C64, AMD XCN05017 provides the manufacturer cross-reference for pin-for-pin XC2C64A upgrades.
合規資訊
RoHS compliance is identified for the exact XC2C64A-7VQG44C listing. Other compliance fields are not stated in the product documentation.