XC2C64A-7VQG44I - 64-Macrocell 159MHz CPLD | AMD
MPN: XC2C64A-7VQG44I ✓ ActiveXC2C64A-7VQG44I Overview
A CPLD, or complex programmable logic device, is a programmable semiconductor that converts digital logic descriptions into fixed hardware interconnections. Within the product hierarchy, the XC2C64A belongs to the CoolRunner-II family of CPLDs, joining other programmable-logic devices and FPGAs used for control, interface, glue logic, and signal-processing functions. Unlike a microcontroller, a CPLD executes configured logic directly in hardware after programming.
The device provides 64 macrocells and approximately 1,500 logic gates for implementing combinational and sequential functions. Its 33 I/O pins support connections to external memory, control signals, displays, sensors, and communications circuitry. The -7 speed designation corresponds to a listed 6.7 ns propagation delay, while the 159 MHz figure describes the maximum operating frequency used when evaluating timing performance.
The 0.18 µm CMOS implementation and 1.8 V core operation place the XC2C64A in the CoolRunner-II architecture designed for low-voltage, high-density programmable logic. The manufacturer data sheet also identifies the device as an in-system-programmable CPLD, allowing configuration data to be loaded through the device's programming interface while the surrounding system is operating.
Typical applications include industrial control and data-acquisition modules, communications-interface logic, test equipment, embedded system support functions, display and keypad controllers, and general-purpose board glue logic. Its combination of 64 macrocells, 33 I/O, and a 44-pin package makes it useful when a design requires more logic than a small GAL or simple fuse-programmed device but does not need a larger FPGA.
Designers should preserve the package's exact pin assignments in the PCB library and follow the CoolRunner-II programming, decoupling, and termination guidance in AMD document DS311. Timing closure should use the speed-grade and I/O constraints appropriate to the selected clocking scheme rather than relying only on the 159 MHz headline frequency.
This page combines the manufacturer's CoolRunner-II technical information with package-aware replacement guidance, design notes, and application-focused selection criteria. These engineering resources help identify where the XC2C64A-7VQG44I fits, which same-package variants can simplify sourcing, and which design checks should be completed before layout release.
Drop-in alternatives for XC2C64A-7VQG44I — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.
Variants in this series
Same-series models that are drop-in compatible with XC2C64A-7VQG44I (same form factor and footprint) — differing in Process Technology, Device Type, Package, RoHS Status, Configuration Memory.
XC2C64A-7VQG44C
✅ Drop-InContact for price
View Datasheet →XA2C64A-7VQG44I
✅ Drop-In📋 Reference alternative (not in catalog)
XC2C64A-6VQG44C
✅ Drop-In ⚠️ Specs Unverified📋 Reference alternative (not in catalog)
XC2C64A-5VQG44C
✅ Drop-InContact for price
View Datasheet →XA2C64A-5VQG44C
✅ Drop-In ⚠️ Specs Unverified📋 Reference alternative (not in catalog)
XC2C64A-7VQG44I Maximum Ratings & Electrical Characteristics
| Programmable Type | In-System Programmable |
| Number of Macrocells | 64 macrocells |
| Number of I/O | 33 I/O |
| Logic Gate Count | 1,500 gates |
| Maximum Operating Frequency | 159 MHz |
| Propagation Delay | 6.7 ns |
| Process Technology | 0.18 µm CMOS |
| Core Supply Voltage | 1.8 V |
| Device Family | CoolRunner-II |
| Speed Grade | -7 |
| Package Type | VTQFP-44 |
| Pin Count | 44 pins |
| Package Dimensions | 10 x 10 mm |
| Mounting Type | Surface Mount |
| RoHS Status | RoHS Compliant |
| Lead-Free Status | Lead Free |
XC2C64A-7VQG44I 10 x 10 mm Pin Configuration Guide
Pin configuration for XC2C64A-7VQG44I (10 x 10 mm package). This digital IC includes GPIO, communication interfaces (UART, SPI, I2C), and power pins. Refer to the manufacturer datasheet for alternate pin functions and configuration options. Essential for embedded system design and PCB layout.
No detailed pinout data available for XC2C64A-7VQG44I.
Refer to the datasheet for full pin configuration.
Typical Applications
XC2C64A-7VQG44I is suitable for 6 applications: Industrial Control Logic, Data-Acquisition Interface, Communications Interface, Test and Measurement Equipment, Display and Keypad Controller, Board Glue Logic.
Industrial Control Logic
The XC2C64A-7VQG44I fits industrial control modules that require deterministic programmable logic close to sensors, relays, and actuators. Its 64 macrocells can implement state machines, interlocks, alarm handling, and signal conditioning, while 33 I/O provide a practical interface to field wiring and embedded controllers. The 159 MHz maximum operating frequency supports fast control paths without requiring a larger FPGA. For a -7 design, verify every timing path against the 6.7 ns propagation-delay specification and retain the exact AMD pin assignments in the 44-pin VTQFP footprint. Industrial temperature and EMC requirements should be confirmed against the selected device grade before production release.
Recommended
Data-Acquisition Interface
The XC2C64A-7VQG44I can coordinate digital data acquisition in instruments that combine analog front ends with FPGA-based or microcontroller-based processing. Its 33 I/O can handle sample-control signals, trigger routing, status flags, and programmable test sequences, while the 64 macrocells support counters, FIFO control, and timing state machines. The 159 MHz operating ceiling provides margin for synchronous control logic at practical system clock rates. Place the CPLD close to the acquisition circuitry to reduce control-loop propagation delay, and follow AMD DS311 for bypass capacitors, I/O standards, and pin constraints.
Recommended
Communications Interface
The XC2C64A-7VQG44I is suitable for communications equipment that needs dedicated protocol framing, buffering, and control logic alongside a host processor. Its 33 I/O support parallel data paths, chip-select signals, and handshake lines, while 64 macrocells allow multiple finite-state machines to operate concurrently. The -7 speed grade and 159 MHz maximum frequency are useful for synchronous interface logic where predictable timing is important. Engineers should assign I/O standards according to the connected bus, add the required termination, and use AMD document DS311 to validate signal integrity, pin locations, and timing constraints.
Recommended
Test and Measurement Equipment
The XC2C64A-7VQG44I can implement sequencing, trigger, and instrument-control logic in test systems. Its 64 macrocells provide enough capacity for timing generators, pattern counters, status encoding, and communication adapters, while the 33 I/O interface with external fixtures and measurement hardware. The listed 159 MHz maximum frequency supports fast digital control and data organization. Layout should separate sensitive clock and data routing from switching nodes, and the implemented logic should be checked against the -7 timing constraints in AMD DS311 after synthesis and place-and-route.
Recommended
Display and Keypad Controller
The XC2C64A-7VQG44I can control displays, keypads, and human-interface logic in embedded equipment. Its 33 I/O are sufficient for parallel display segments, button scanning, indicators, and control signals, while the 64 macrocells can hold refresh counters, debounce logic, and display multiplexers. A 159 MHz device maximum gives substantial timing headroom for common scan-based interfaces. Engineers should define the pin assignment in the design tool, check the selected voltage standards, and keep the 44-pin VTQFP footprint aligned with the physical package orientation before fabrication.
Recommended
Board Glue Logic
The XC2C64A-7VQG44I is useful for board-level glue logic that bridges processors, memories, sensors, and peripheral devices. It can implement arbitration, address decoding, reset distribution, interrupt handling, and protocol conversion without occupying a larger programmable-logic package. With 64 macrocells and 33 I/O, the device balances logic capacity against package size, and its 159 MHz maximum frequency supports common peripheral-clock rates. For dependable implementation, apply the recommended decoupling, preserve programming access, and verify all timing-critical paths using the selected speed grade and AMD DS311 constraints.
Recommended
Recommended Products Summary
Engineering reference data for XC2C64A-7VQG44I — comparison, design guidance, and compliance information.
Selection Guide
Comparison with Alternatives
| Parameter | This Product | XC2C64A-7VQG44C | XA2C64A-7VQG44I | XC2C64A-6VQG44C | XC2C64A-5VQG44C |
|---|---|---|---|---|---|
| Brand | AMD | AMD | AMD | AMD | AMD |
| Package | VTQFP-44 (10 x 10 mm) | VTQFP-44 (10 x 10 mm) | VTQFP-44 (10 x 10 mm) | VTQFP-44 (10 x 10 mm) | VTQFP-44 (10 x 10 mm) |
| Macrocells | 64 macrocells | 64 macrocells | 64 macrocells | 64 macrocells | 64 macrocells |
| User I/O | 33 I/O | 33 I/O | 33 I/O | 33 I/O | 33 I/O |
| Core Supply Voltage | 1.8 V | 1.8 V | 1.8 V | 1.8 V | 1.8 V |
| Speed Grade | -7 | -7 | -7 | -6 | -5 |
| Programming Type | In-System Programmable | In-System Programmable | In-System Programmable | In-System Programmable | In-System Programmable |
Key Differentiators
- Faster timing grade than the lower-speed same-package options (vs XC2C64A-5VQG44C)
- Maintains 159 MHz maximum operating frequency with 64 macrocells (vs XC2C64A-6VQG44C)
- Same-package sourcing flexibility without changing the PCB footprint (vs XC2C64A-7VQG44C)
- Industrial-oriented ordering option versus the automotive-designated variant (vs XA2C64A-7VQG44I)
Design Notes
Create the PCB footprint from the 44-pin VTQFP package drawing in AMD document DS311 and verify pin 1, pin numbering, pad dimensions, and exposed-area requirements against the mechanical drawing. Do not reuse a generic 44-pin footprint solely because its lead count matches. Check the assembled orientation and soldering process, then confirm that programming access and all I/O routes remain reachable within the routed board geometry.
Follow the core and I/O supply connection and decoupling requirements in DS311, including the applicable bypass capacitors and supply sequencing limits. Place each required capacitor immediately adjacent to its assigned power pin, with a short return path and a solid ground reference. Avoid sharing narrow supply traces between unrelated programmable-logic sections, and verify the assembled rail voltages against every I/O standard enabled in the design.
Assign I/O standards from the device data sheet rather than from board-level intuition. Match edge rates, drive strength, pull-up or pull-down requirements, and external termination to the connected device and trace topology. Keep clock routing short and away from noisy switching nodes, use a continuous reference plane, and review high-speed edges with the actual PCB stack-up. Programming and configuration pins also deserve clean routing because glitches or contention can affect initialization.
A common mistake is treating every XC2C64A suffix as interchangeable even though speed, temperature, and package identifiers encode different constraints. Another is relying on the 159 MHz maximum frequency without checking the actual routed path. Review the complete ordering table, constrain every clock domain, and run post-route timing analysis. The same 44-pin footprint enables substitution, but it does not guarantee identical qualification or environmental suitability.
Compliance Information
RoHS Compliant and Lead Free are identified for the XC2C64A-7VQG44I. REACH, halogen-free, and conflict-minerals status are not stated.