ADF4212LBRUZ-RL - 2.4GHz Dual PLL Synthesizer | Analog Devices
料号: ADF4212LBRUZ-RL ✓ 量产中ADF4212LBRUZ-RL 概述
A phase-locked loop, or PLL, is a frequency-control circuit that compares an output signal with a reference frequency and uses feedback to maintain a stable relationship between them. The ADF4212L belongs to the frequency synthesizer hierarchy, where PLL synthesizers support voltage-controlled oscillators in communication transmitters and receivers. The ADF4212L series is specifically positioned for dual RF and IF local-oscillator generation.
The synthesizer supports RF and IF prescaler ratios of 8/9, 16/17, 32/33, and 64/65. Programmable charge-pump currents support different loop-filter and phase-error requirements, while analog and digital lock detection allow a system to monitor operating state. The 3-wire serial interface simplifies connection with a host controller, and the power-down mode helps reduce consumption when the synthesizer is not in use.
Its 2.7 V to 5.5 V power-supply range supports both 3 V and 5 V system architectures. A separate charge-pump supply permits an extended tuning-voltage range, which is useful when the external voltage-controlled oscillator requires more headroom than the main supply provides. The low-power ADF4212L variant is intended to reduce total current when dual RF and IF synthesis is required.
Typical uses include wireless receiver and transmitter local oscillators, frequency conversion in RF and IF signal paths, communication infrastructure, instrumentation, and test equipment. Each PLL can support a separate local-oscillator path, reducing external synthesizer count when a design requires both RF and IF frequencies.
PCB implementation should preserve a compact loop-filter layout near the charge-pump and synthesizer outputs. The digital interface, reference input, power rails, and RF/IF inputs require careful grounding and decoupling. The external reference and loop-filter components determine phase-noise performance, lock time, and tuning range.
This product record combines the manufacturer’s device description, package and frequency information, and practical implementation guidance with a structured comparison against other Analog Devices synthesizer choices. It also identifies where pin, electrical, and lifecycle details must be confirmed directly in the manufacturer documentation before a new layout is released.
直接替换替代料: ADF4212LBRUZ-RL ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: ADF4212LBRUZ-RL (相同外形与封装尺寸) ——差异在于 Package, Device Type, Charge Pump Current, Power-Down Mode, Serial Interface.
ADF4212LBRUZ-RL7
✅ 直接替换📋 参考替代料(不在目录中)
ADF4212LBRU
✅ 直接替换📋 参考替代料(不在目录中)
ADF4212BRUZ-RL
✅ 直接替换📋 参考替代料(不在目录中)
ADF4212BRUZ
✅ 直接替换联系询价
查看数据手册 →ADF4212LBRUZ-RL 规格参数
| Device Type | Dual RF/IF PLL frequency synthesizer |
| Maximum RF Input Frequency | 2.4 GHz |
| Maximum IF Input Frequency | 1.0 GHz |
| Supply Voltage Range | 2.7 V to 5.5 V |
| Architecture | Dual phase-locked loop |
| RF/IF Prescaler Ratios | 8/9, 16/17, 32/33, and 64/65 |
| Charge Pump Current | Programmable |
| Reference Counter | 15-bit programmable R counter |
| Serial Control Interface | 3-wire |
| Lock Detection | Analog and digital |
| Fastlock Mode | Supported |
| Power-Down Mode | Supported |
| Charge Pump Supply | Separate VP supply |
| Total IDD | 7.5 mA |
| 封装 | 20-pin TSSOP, 0.173 in (4.40 mm) width |
| 安装类型 | Surface mount |
| Temperature Grade | Industrial |
| RoHS 状态 | Compliant |
ADF4212LBRUZ-RL 20-pin tssop, 0.173 in (4.40 mm) width 引脚配置指南
ADF4212LBRUZ-RL(20-pin tssop, 0.173 in (4.40 mm) width 封装)的引脚配置。 引脚编号、功能和连接图在制造商数据手册中定义。请参阅该手册以了解确切的封装尺寸和焊接指南。
暂无详细引脚数据: ADF4212LBRUZ-RL.
请参阅 数据手册 以查看完整引脚配置。
典型应用
ADF4212LBRUZ-RL 适用于 6 应用s: Wireless Transmitter Local Oscillator, Wireless Receiver IF Local Oscillator, Dual-Band RF Frequency Conversion, RF Test and Measurement Instrument, Low-Power Communication Equipment, Frequency Conversion in Industrial Systems.
Wireless Transmitter Local Oscillator
The ADF4212LBRUZ-RL fits a wireless transmitter that requires an RF local oscillator for an up-conversion mixer. Its RF input bandwidth reaches 2.4 GHz, allowing the PLL to evaluate a divided VCO output against the programmable reference path. The external VCO and loop filter set practical phase noise and lock time, while the device’s 2.7 V to 5.5 V supply range supports 3 V and 5 V radio architectures. The 20-pin TSSOP package also keeps the implementation compatible with the broader ADF4212 family footprint.
推荐
Wireless Receiver IF Local Oscillator
The second synthesizer channel in the ADF4212LBRUZ-RL can generate an IF local-oscillator signal alongside an RF local oscillator. Its 1.0 GHz IF bandwidth directly addresses low- and intermediate-frequency receiver architectures, while the RF channel remains available up to 2.4 GHz. The dual architecture can reduce the number of separate PLL packages in a receiver. Design attention should remain on reference routing, independent loop filters, VCO tuning-voltage headroom, and isolation between the two RF-sensitive signal paths.
推荐
Dual-Band RF Frequency Conversion
The ADF4212LBRUZ-RL is appropriate for RF systems that need separate local-oscillator paths for different conversion stages. The RF channel supports frequencies through 2.4 GHz, and the IF channel supports frequencies through 1.0 GHz. This arrangement can simplify the control layout compared with using two unrelated synthesizers because both channels are programmed through the same 3-wire interface family. The design trade-off is shared supply and reference infrastructure, which must be laid out carefully to prevent coupling from the charge-pump and digital programming paths into the VCOs.
推荐
RF Test and Measurement Instrument
The ADF4212LBRUZ-RL can support programmable local-oscillator generation in RF instrumentation because two channels provide RF and IF synthesis from a common reference. Its programmable prescaler ratios of 8/9, 16/17, 32/33, and 64/65 support division choices appropriate to different VCO frequencies. Programmable charge-pump current permits the loop design to be adapted to different phase-error and lock requirements. The principal system-level considerations are reference phase noise, loop-filter component selection, and isolation between the synthesizer, VCO, and measurement paths.
推荐
Low-Power Communication Equipment
The ADF4212LBRUZ-RL is appropriate for portable or low-power communication equipment that benefits from a compact dual-frequency synthesizer. Its low-power ADF4212L identity and 7.5 mA total IDD provide a concrete advantage over the standard ADF4212 family when supply consumption is important. The 20-pin TSSOP package limits board area, while the 2.7 V to 5.5 V operating range supports compact system rails. Designers should still evaluate total power including the external VCO, reference source, charge-pump circuitry, and any required output buffering.
推荐
Frequency Conversion in Industrial Systems
An industrial RF system can use the ADF4212LBRUZ-RL when one subsystem requires both an RF local oscillator and an IF local oscillator. The dual PLL organization allows both synthesis paths to share reference and controller resources, reducing board-space demands compared with separate devices. The 2.4 GHz RF and 1.0 GHz IF limits align with many frequency-conversion architectures, while the low-power L-series designation suits compact embedded equipment. Industrial implementation should include grounding, filtering, and qualification checks based on the actual operating environment rather than assumptions about generic RF performance.
推荐
推荐产品汇总
工程参考数据: ADF4212LBRUZ-RL ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | ADF4212LBRUZ-RL7 | ADF4212LBRU | ADF4212BRUZ-RL | ADF4212BRUZ |
|---|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | 20-pin TSSOP | 20-pin TSSOP - same | 20-pin TSSOP - same | 20-pin TSSOP - same | 20-pin TSSOP - same |
| Product Family | ADF4212L low-power dual PLL | ADF4212L low-power dual PLL | ADF4212L low-power dual PLL | ADF4212 standard dual PLL | ADF4212 standard dual PLL |
| Maximum RF Frequency | 2.4 GHz | 2.4 GHz | 2.4 GHz | 2.4 GHz | 2.4 GHz |
| Maximum IF Frequency | 1.0 GHz | 1.0 GHz | 1.0 GHz | 1.0 GHz | 1.0 GHz |
| Supply Voltage Range | 2.7 V to 5.5 V | 2.7 V to 5.5 V | 2.7 V to 5.5 V | 2.7 V to 5.5 V | 2.7 V to 5.5 V |
| Prescaler Ratios | RF/IF: 8/9, 16/17, 32/33, 64/65 | RF/IF: 8/9, 16/17, 32/33, 64/65 | RF/IF: 8/9, 16/17, 32/33, 64/65 | RF/IF: 8/9, 16/17, 32/33, 64/65 | RF/IF: 8/9, 16/17, 32/33, 64/65 |
| Control Interface | 3-wire serial interface | 3-wire serial interface | 3-wire serial interface | 3-wire serial interface | 3-wire serial interface |
| Lock Detection | Analog and digital | Analog and digital | Analog and digital | Analog and digital | Analog and digital |
关键差异点
- Low-power dual PLL implementation (对比 ADF4212BRUZ-RL)
- Dual RF and IF synthesis in one package (对比 ADF4212LBRU)
- Broad prescaler selection (对比 ADF4212BRUZ)
- Separate extended tuning-voltage supply (对比 ADF4212LBRUZ-RL7)
设计说明
Place each synthesizer channel’s loop-filter components close to the associated charge-pump output and VCO control input. Keep the 3-wire programming traces away from RF and IF inputs, and provide a solid ground plane with short return paths. The separate VP supply should be decoupled locally because its voltage sets the available VCO tuning range.
Route the reference signal as a controlled-impedance trace and keep it isolated from charge-pump outputs and switching supplies. Reference phase noise can directly limit synthesizer phase noise, while clock-like programming activity may couple into sensitive RF paths. Use ground guards and short digital return paths where the board stackup permits.
Design the supply network for both the 2.7 V to 5.5 V main rail and the separate VP charge-pump rail. Follow the manufacturer’s recommended decoupling values and route each capacitor directly to its relevant power pin. Confirm that the VP range covers the external VCO tuning-voltage requirement rather than assuming the main supply provides sufficient headroom.
Do not substitute a standard ADF4212 and an ADF4212L solely because both use a 20-pin TSSOP package. The L-series designation identifies the low-power variant with 7.5 mA total IDD. Before replacement, verify pin functions, register behavior, lock-detect implementation, electrical limits, and the intended tape-and-reel ordering suffix in the Analog Devices documentation.
合规信息
RoHS compliance is indicated in the product comparison information for the ADF4212 family. Other compliance declarations are not established by the cited product records.