Analog Devices

ADF4213BRU-REEL - 3 GHz PLL Frequency Synthesizer | Analog Devices

料号: ADF4213BRU-REEL ✓ 量产中
2.7 V to 5.5 V Vdss 20-TSSOP, 4.40 mm width Package 3 GHz Speed
最小起订量: 1 |

ADF4213BRU-REEL 概述

The Analog Devices ADF4213BRU-REEL is an RF/IF clock and frequency synthesizer with a 3 GHz maximum output frequency, a differential phase-detector input, and a 20-lead TSSOP package. It is designed for precision frequency generation, clock multiplication, and phase-locked-loop control in communications, test equipment, and industrial electronic systems.

A PLL frequency synthesizer belongs to the clock-generation and timing-control hierarchy: it compares a phase-detector input with a divided feedback signal, drives an internal charge pump and voltage-controlled oscillator, and then locks an output frequency to a stable reference. The ADF4213 combines this phase-locking architecture with a programmable divider, allowing a relatively low-frequency reference to establish an RF output up to 3 GHz.

Key characteristics include a 3 GHz maximum synthesis frequency, a 20-TSSOP package, CMOS input and clock outputs, and operation from a 2.7 V to 5.5 V supply. A separate charge-pump supply permits an extended tuning voltage, while the programmable feedback divider supports integer-N frequency synthesis. These features make the device suitable where the output must be derived accurately from a reference clock without using a separate high-frequency oscillator.

The device is specified as a single PLL with one clock output and a differential input/output phase-detector arrangement. Its architecture supports applications spanning RF and IF signal chains, microwave down-conversion, clock generation, and phase locking. The separate charge-pump supply is particularly useful when the required tuning range exceeds what the main analog supply can provide.

Typical uses include RF receivers, transmit and receive conversion stages, frequency analyzers, laboratory instruments, and industrial frequency-generation equipment. When its output drives a mixer or converter, system phase noise, reference quality, loop bandwidth, and integer-N division ratio directly influence the final signal quality.

A key design consideration is the power relationship between the analog supply, charge-pump supply, and output buffer. Decoupling capacitors should be placed close to the supply pins, while the reference and feedback routes should remain short and controlled. The 20-pin TSSOP footprint requires careful assembly spacing and thermal verification under the maximum expected operating condition.

This page combines device specifications, practical PLL design guidance, drop-in alternatives, application fit, and engineering trade-offs to support faster component selection and PCB implementation.

直接替换替代料: ADF4213BRU-REEL ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。

本系列中的变体

可与以下型号直接替换的同系列型号: ADF4213BRU-REEL (相同外形与封装尺寸) ——差异在于 Package, Charge Pump, Device Type, PLL Architecture, Product Type.

Analog Devices
Package: 20-pin LFCSP with exposed pad
Charge Pump: Precision charge pump with programmable currents
Device Type: Single, integer-N RF PLL frequency synthesizer
对比 ADF4213BRU-REEL →
Analog Devices
Package: 20-pin TSSOP, 0.173 in (4.40 mm) width
Device Type: Dual RF/IF PLL frequency synthesizer
对比 ADF4213BRU-REEL →
Analog Devices
Package: 20-pin TSSOP, 4.40 mm body width
Charge Pump: Selectable current
PLL Architecture: Integer-N
对比 ADF4213BRU-REEL →

ADF4216BRU-REEL

✅ 直接替换
Analog Devices
📦 20-TSSOP
Dual RF PLL frequency synthesizer (integer-N) · 550 MHz to 1.2 GHz · 5 MHz to 1.2 GHz · 2.7 V to 5.5 V · 3 V to 5.5 V · 64/65 selectable dual modulus · 16/17 selectable dual modulus · Selectable

联系询价

查看数据手册 →

ADF4216BRUZ-RL

✅ 直接替换
Analog Devices
📦 20-TSSOP
Clock/Frequency Synthesizer (RF/IF) IC · Integer-N · 1.2 GHz · 1 circuit · 3:1 · CMOS · Clock · 16/17

联系询价

查看数据手册 →

ADF4212LBRUZ-RL

✅ 直接替换
Analog Devices
📦 20-TSSOP
Dual RF/IF PLL frequency synthesizer · 2.4 GHz · 1.0 GHz · 2.7 V to 5.5 V · Dual phase-locked loop · 8/9, 16/17, 32/33, and 64/65 · Programmable · 15-bit programmable R counter

联系询价

查看数据手册 →

ADF4113BRU-REEL

✅ 直接替换
📦 20-TSSOP
Different PLL family with a 4 GHz maximum frequency, 1 GHz higher than the 3 GHz target; exact pin and register compatibility requires confirmation.

📋 参考替代料(不在目录中)

ADF4112BCP-REEL

✅ 直接替换 ⚠️ 规格未核验
Analog Devices
📦 20-TSSOP
Single, integer-N RF PLL frequency synthesizer · 3.0 GHz · 5 MHz to 3.0 GHz · Programmable dual-modulus P/P+1 prescaler · Low-noise digital PFD · Precision charge pump with programmable currents · Separate VP supply · Programmable

联系询价

查看数据手册 →

ADF4213BRU-REEL 规格参数

Product Type Clock/frequency synthesizer IC
PLL Architecture 1 PLL
Maximum Output Frequency 3 GHz
Minimum Output Frequency 0 MHz
工作电源电压 2.7 V to 5.5 V
Input Signal Type CMOS
Output Signal Type Clock
Phase Detector Input Differential
Maximum Input-to-Output Ratio 3:1
Number of Circuits 1 circuit
Charge Pump Supply Separate VP supply
安装类型 Surface mount
封装 20-TSSOP, 4.40 mm width
Terminal Count 20 terminals
Packaging Tape and reel
Temperature Grade Industrial grade
RoHS 状态 Unknown
REACH Status Unknown
AEC-Q100 Qualification Not applicable

ADF4213BRU-REEL 20-tssop, 4.40 mm width 引脚配置指南

ADF4213BRU-REEL(20-tssop, 4.40 mm width 封装)的引脚配置。 引脚编号、功能和连接图在制造商数据手册中定义。请参阅该手册以了解确切的封装尺寸和焊接指南。

ADF4213BRU-REEL 的 20-tssop, 4.40 mm width 封装引脚图

暂无详细引脚数据: ADF4213BRU-REEL.

请参阅 数据手册 以查看完整引脚配置。

典型应用

ADF4213BRU-REEL 适用于 6 应用s: RF Receiver Clock Generation, Microwave Down-Conversion, Precision Test Instrumentation, Industrial Frequency Generator, Clock Multiplier Module, Communication IF Signal Path.

🌐

RF Receiver Clock Generation

The ADF4213BRU-REEL can generate an RF or IF clock up to 3 GHz from a stable reference, allowing receiver conversion stages to share one frequency source. Its differential phase-detector input and programmable feedback divider suit integer-N phase-locked-loop designs. The main design benefit is avoiding an independent high-frequency oscillator, although reference phase noise and the divider ratio set a practical limit on close-in phase noise.

🌐

Microwave Down-Conversion

A 3 GHz synthesis range makes ADF4213BRU-REEL useful for driving a local oscillator in microwave down-conversion and frequency-conversion equipment. The separate charge-pump supply supports an extended tuning range for a voltage-controlled oscillator. Designers should center the loop bandwidth on the required channel spacing and verify phase-noise performance with the actual reference frequency, integer-N division ratio, and loop-filter component values.

🖥️

Precision Test Instrumentation

ADF4213BRU-REEL can provide a programmable RF reference for laboratory and production-test equipment. Its output range reaches 3 GHz, enabling the same synthesizer architecture to serve multiple instrument bands. For accurate measurements, the reference oscillator should have low phase noise, and the loop filter should be recalculated whenever the output frequency or required lock time changes rather than reusing settings from another channel.

🏭

Industrial Frequency Generator

The ADF4213BRU-REEL fits industrial frequency-generation modules that require a stable, tunable clock without a separate RF oscillator. Its 2.7 V to 5.5 V operating range supports embedded control-system rails, while the 20-TSSOP package simplifies compact board assembly. Industrial designs should account for temperature drift, reference quality, supply variation, and worst-case lock behavior across the complete operating range.

🖥️

Clock Multiplier Module

ADF4213BRU-REEL can multiply a low-frequency reference into an RF clock by using its programmable feedback divider and phase-locked loop. This is useful in modular clock-distribution systems where several instruments need a common phase-coherent signal. The design must preserve a low-noise reference path, use the recommended loop-filter topology, and account for integer-N spur behavior at the final output frequency.

📡

Communication IF Signal Path

ADF4213BRU-REEL is suitable for generating local oscillator or intermediate-frequency clocks in communication receivers and transmitters. Its CMOS clock output and differential phase-detector interface provide the fundamental building blocks for a phase-locked signal chain. The main trade-off is the integer-N architecture, where a high division ratio can increase in-band phase noise, so reference selection and loop design remain critical.

What is the maximum operating frequency of ADF4213BRU-REEL?
The ADF4213BRU-REEL supports a maximum output frequency of 3 GHz. According to the manufacturer datasheet, it is a single-PLL clock and frequency synthesizer using a differential phase-detector input and a CMOS clock output. This makes it appropriate for RF and IF frequency-generation stages that must derive a high-frequency output from a lower-frequency reference source.
What supply voltage does ADF4213BRU-REEL operate from?
The ADF4213BRU-REEL operates from 2.7 V to 5.5 V. The manufacturer datasheet also identifies a separate charge-pump supply, designated VP, that can support an extended tuning voltage. The main supply and charge-pump rails should therefore be evaluated independently when designing the power distribution network and checking the allowable voltage on each pin.
Where can I download the ADF4213BRU-REEL datasheet?
The ADF4213BRU-REEL datasheet can be obtained from the Analog Devices product documentation or the official ADF4213 datasheet PDF. It contains the authoritative pin-description table, recommended application circuit, register information, electrical characteristics, and package drawing. Use the pin-description table when assigning PCB signals because the 20-lead TSSOP includes power, ground, reference, feedback, and control functions.
Where is the pinout for ADF4213BRU-REEL?
The authoritative ADF4213BRU-REEL pinout is in the manufacturer datasheet pin-description table. The component uses a 20-lead TSSOP package, and each terminal should be assigned according to that table rather than inferred from neighboring parts. Use the exposed package drawing and pin-numbering convention to preserve orientation during PCB layout and assembly.
What kind of component is ADF4213BRU-REEL?
The ADF4213BRU-REEL is a clock/frequency synthesizer IC with one phase-locked loop. The manufacturer datasheet identifies a maximum frequency of 3 GHz, a differential phase-detector input, a CMOS clock output, and a 20-TSSOP package. It belongs to the clock-generation and timing-control category and is intended for RF, IF, and precision clock-synthesis systems.
How does a PLL frequency synthesizer generate a 3 GHz output?
A PLL frequency synthesizer locks an internal voltage-controlled oscillator to a reference by comparing a divided feedback signal with the phase-detector input. The charge pump and loop filter then control the oscillator until the phase error is minimized. In the ADF4213BRU-REEL, the programmable feedback path allows a stable reference to establish an output frequency up to 3 GHz.
What can replace ADF4213BRU-REEL?
The closest documented replacements are ADF4216BRU-REEL, ADF4216BRUZ-RL, and ADF4212LBRUZ-RL because they use the same 20-TSSOP format and appear in a direct comparison for ADF4213BRU. Their frequency limits and tuning specifications differ, so a replacement must be checked against the required output frequency, loop settings, register map, and charge-pump requirements before PCB reuse is approved.
Is ADF4216BRU-REEL the same as ADF4213BRU-REEL?
No. ADF4216BRU-REEL is pin- and package-compatible with ADF4213BRU-REEL according to the cited comparison, but it does not have identical performance. The ADF4216 family is associated with a lower maximum synthesis frequency than the 3 GHz ADF4213BRU-REEL. Confirm the required channel frequency and recalculate the loop filter before treating the parts as interchangeable.
ADF4213BRU-REEL vs ADF4212LBRUZ-RL - which is better for RF synthesis?
Choose ADF4213BRU-REEL when the design requires operation up to 3 GHz, and choose ADF4212LBRUZ-RL only when its lower frequency capability covers the complete required tuning range. Both are presented as 20-TSSOP clock solutions with compatible terminal arrangements, but the output-frequency ceiling and related PLL characteristics differ. Frequency coverage must be the primary selection criterion.
When should I choose ADF4213BRU-REEL over a lower-frequency PLL?
Choose ADF4213BRU-REEL when the synthesizer must generate a signal above the tuning range of a lower-frequency PLL and the target frequency does not exceed 3 GHz. Its differential phase-detector input, separate charge-pump supply, and programmable feedback divider support RF and IF clock architecture. A lower-frequency part may still be preferable when required output range is modest.
Is ADF4213BRU-REEL suitable for RF receiver and mixer applications?
Yes. ADF4213BRU-REEL is suitable for RF receiver, mixer, and IF-conversion applications because its PLL can synthesize a clock up to 3 GHz from a reference source. Practical performance depends on reference phase noise, loop bandwidth, integer-N division ratio, charge-pump settings, and output filtering. Those conditions should be evaluated before confirming adequate system phase noise.
What is the best Analog Devices equivalent for ADF4213BRU-REEL?
ADF4216BRU-REEL is the closest cited Analog Devices alternative for an existing 20-TSSOP design, but its maximum frequency is lower than the ADF4213BRU-REEL's 3 GHz capability. It is therefore suitable only when the required channel remains inside its tuning range. Register compatibility, reference setup, loop-filter values, and output-drive requirements must also be reviewed.
How should the ADF4213BRU-REEL reference and feedback paths be routed?
Route the reference and feedback connections as short, controlled-impedance paths and keep them away from noisy switching nodes and the charge-pump output. The manufacturer application circuit should be used as the basis for component placement and grounding. Because loop phase noise is strongly influenced by reference jitter, divider ratio, and loop bandwidth, preserve the recommended topology rather than changing it without recalculation.
What are the important design considerations for ADF4213BRU-REEL?
The main design considerations are supply decoupling, loop-filter selection, reference routing, output filtering, and PCB grounding. According to the manufacturer datasheet, the device supports a 2.7 V to 5.5 V operating supply and a separate VP charge-pump supply. Keep supply and bypass connections compact, isolate sensitive feedback paths, and verify the complete loop at the intended reference and output frequencies.
What is the price of ADF4213BRU-REEL?
Current commercial terms for ADF4213BRU-REEL should be obtained through the Request a Quote form on this page as of 2026-11-20. The quote form allows the required quantity, delivery target, and packaging preference to be entered for an accurate response. Availability and lead time should be confirmed at the same time because the reel designation is an orderable package configuration.
Where can I buy ADF4213BRU-REEL and what is the lead time?
Use the Request a Quote form on this page to request ADF4213BRU-REEL pricing, availability, minimum order quantity, and lead time as of 2026-11-20. This form is the appropriate route for a quote-based component order and avoids relying on a static listing that may not reflect current production allocation. Provide the required reel quantity and target delivery date for the fastest response.

工程参考数据: ADF4213BRU-REEL ——对比、设计指导和合规信息。

选型指南

Choose ADF4213BRU-REEL when the design requires an integer-N PLL clock or local-oscillator output reaching 3 GHz and uses a 20-TSSOP footprint. ADF4216BRU-REEL or ADF4216BRUZ-RL may permit PCB reuse for designs whose required frequency falls within their lower tuning range, but the loop settings and register behavior must be rechecked. ADF4212LBRUZ-RL is appropriate only when its 1.2 GHz ceiling covers the design, so it is not a direct substitute for high-frequency channels. ADF4113BRU-REEL offers a higher 4 GHz ceiling but belongs to a different PLL family and may require different programming, reference, and loop-filter details. Confirm package pins, voltage ratings, register compatibility, output drive, reference frequency, and phase-noise requirements before approving any substitution.

与替代料对比

参数 本产品 ADF4216BRU-REEL ADF4216BRUZ-RL ADF4212LBRUZ-RL ADF4113BRU-REEL ADF4112BCP-REEL
Brand Analog Devices Analog Devices Analog Devices Analog Devices Analog Devices Analog Devices
Package 20-TSSOP 20-TSSOP 20-TSSOP 20-TSSOP 20-TSSOP 20-TSSOP
Terminal Count 20 20 20 20 20 20
Mounting Type Surface mount Surface mount Surface mount Surface mount Surface mount Surface mount

关键差异点

  • Higher maximum synthesis frequency than the documented ADF4212-class alternative (对比 ADF4212LBRUZ-RL)
  • Lower maximum frequency than the ADF4113 alternative (对比 ADF4113BRU-REEL)
  • Documented 20-TSSOP terminal and package consistency (对比 ADF4216BRU-REEL)

设计说明

Decouple the 2.7 V to 5.5 V supply close to the relevant device pins and connect the exposed return network to a low-impedance ground plane. The separate VP charge-pump rail permits an extended tuning voltage, so its allowable range must be checked independently from the main analog supply. Keep the charge-pump connection short and isolate it from sensitive reference and feedback traces.

Use the manufacturer application circuit as the baseline for the reference, phase-detector, feedback, charge-pump, and loop-filter layout. Route high-frequency nodes with short connections and keep the feedback path away from switching and charge-pump nodes. A ground plane is preferable to fragmented return paths because PLL phase-noise performance is sensitive to supply and ground impedance.

The ADF4213BRU-REEL is an integer-N PLL, so reference jitter, division ratio, and loop bandwidth strongly affect output phase noise. Calculate the loop filter for the actual reference and output frequencies, preserve the recommended charge-pump current and output-divider topology, and verify acquisition and lock behavior across temperature and supply tolerance before production release.

合规信息

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
无铅
Unknown
无卤
Unknown
冲突矿物
Unknown

The device is identified as industrial-grade. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status require confirmation from the current manufacturer product documentation.

数据核验日期: 2026-11-20 ——数据由 XAIPART 元器件工程团队核验和整理

相关搜索

ADF4213BRU-REEL datasheet ADF4213BRU-REEL specifications ADF4213BRU-REEL pinout ADF4213BRU-REEL datasheet pdf Analog Devices ADF4213BRU-REEL ADF4213BRU-REEL 3 GHz PLL ADF4213BRU-REEL 20-TSSOP ADF4213BRU-REEL RF synthesizer ADF4213BRU-REEL vs ADF4216BRU-REEL ADF4213BRU-REEL replacement ADF4213BRU-REEL equivalent ADF4213BRU-REEL price ADF4213BRU-REEL stock ADF4213BRU-REEL application circuit

相关元器件 & 术语

Analog Devices ADF4213BRU-REEL ADF4216BRU-REEL ADF4216BRUZ-RL ADF4212LBRUZ-RL ADF4113BRU-REEL ADF4112BCP-REEL PLL phase-locked loop clock generator frequency synthesizer integer-N PLL phase detector charge pump voltage-controlled oscillator 20-TSSOP TSSOP family surface-mount package CMOS differential input RF IF phase noise reference clock RoHS
快速报价
填写完整信息——我们的销售团队将在 24 小时内回复
料号 制造商 封装 QTY 目标价 小计
✓
报价已提交!

我们将在 24 小时内回复您的邮件

1
询价已提交
2
已收到报价
3
已下单
4
支付
5
已发货
6
已送达
查看询价详情