CS5160GD - 5-Bit Dual Synchronous Buck Controller | onsemi
料号: CS5160GD ✗ 停产CS5160GD 概述
A synchronous buck controller is a type of DC-DC converter controller that drives high-side and low-side N-channel MOSFETs to regulate a switching power stage. This topology belongs to the voltage-regulator family and ultimately to the broader power-management IC category. Compared with an asynchronous controller, a synchronous design replaces a rectifier diode with a controlled low-side MOSFET, reducing conduction loss and improving conversion efficiency when the design is implemented with suitable power components.
The defining feature of the CS5160GD is its 5-bit control resolution. This resolution allows the controller to command a larger number of discrete output-voltage steps than a conventional 3-bit controller, supporting finer regulation granularity in systems that need multiple logic rails. Its dual-output architecture also permits a single controller to manage two independent processor rails instead of using separate controller ICs for each rail.
The CS5160 uses current-mode and voltage-mode control, and its internal circuitry is intended for demanding microprocessor and logic applications. According to the onsemi datasheet, the controller is designed to provide unprecedented transient response for high-density, high-speed logic. Its operating switching frequency can reach 1000 kHz, helping the power stage respond quickly to load changes while reducing the output-voltage excursion experienced by the downstream logic.
Typical uses include Intel Pentium II-era computer power systems, microprocessor core-voltage regulation, clock-generation and logic-rail subsystems, and other multi-rail desktop or industrial computing boards. The dual outputs are particularly useful when the processor requires separate core and auxiliary rails with tightly coordinated load transients.
When laying out a CS5160GD design, follow the recommended compensation, MOSFET, inductor, and capacitor selections in the manufacturer datasheet. The 5-bit programming interface and dual-output topology do not guarantee correct sequencing or transient performance by themselves; those outcomes depend on the external power stage, feedback network, and control-loop compensation.
直接替换替代料: CS5160GD ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
CS5160GD16
✅ 直接替换📋 参考替代料(不在目录中)
CS5160GD 最大额定值与电气特性
| Product Type | CPU 5-bit synchronous buck controller |
| Control Resolution | 5 bits |
| 拓扑 | Synchronous dual N-channel buck |
| 输出数量 | 2 outputs |
| Output Current Rating | 1.5 A |
| Maximum Switching Frequency | 1000 kHz |
| Control Mode | Current mode / voltage mode |
| 封装 | 16-pin PDSO (SOIC-16), surface mount |
| Manufacturer | onsemi |
| Application | Intel Pentium II voltage regulation |
| Transient Response | Optimized for high-density, high-speed logic |
CS5160GD 16-pin pdso (soic-16), surface mount 引脚配置指南
CS5160GD(16-pin pdso (soic-16), surface mount 封装)的引脚配置。 该功率器件具有栅极、漏极和源极端子。对于无极性封装,请参阅制造商数据手册以了解确切的引脚 1 方向和封装尺寸细节。常见应用包括电源设计、电机驱动和负载开关。
暂无详细引脚数据: CS5160GD.
请参阅 数据手册 以查看完整引脚配置。
典型应用
CS5160GD 适用于 6 应用s: Legacy Pentium II Processor Core Regulation, Multi-Rail Computer Logic Power, High-Speed Clock and Logic Rail Control, Embedded Legacy Processor Board Repair, Dual-Rail Industrial Logic Supply, CPU Voltage-Sequencing Reference Design.
Legacy Pentium II Processor Core Regulation
The CS5160GD fits legacy Intel Pentium II processor boards because it was developed as a CPU 5-bit synchronous buck controller for the Pentium II voltage-regulator role. Its two outputs can serve separate processor-related rails, while the 5-bit programming interface provides more adjustment steps than a conventional 3-bit controller. The onsemi CS5160 datasheet identifies a 1.5 A rating and up to 1000 kHz switching, characteristics suited to fast-changing logic loads. In a new design, validate the exact voltage table, reference values, compensation, and MOSFET selection against the original motherboard schematics before layout reuse.
推荐
Multi-Rail Computer Logic Power
The CS5160GD can manage two synchronous N-channel buck stages where a legacy computing board needs separate core and auxiliary logic rails. Its dual-output architecture reduces the controller count compared with using two independent regulators, and its 1000 kHz maximum switching frequency supports rapid response to processor load steps. According to the onsemi CS5160 datasheet, the architecture was designed for unprecedented transient response in high-density, high-speed logic. Circuit implementation still depends on accurate voltage programming, per-rail compensation, inductor sizing, and layout that minimizes high-current switching loops.
推荐
High-Speed Clock and Logic Rail Control
The CS5160GD is suitable for clock-generation or dense digital-logic subsystems that require fast rail correction during abrupt load changes. Its 5-bit control resolution allows finer voltage-step commands than a 3-bit controller, while the synchronous N-channel topology reduces the conduction loss associated with an asynchronous rectifier when appropriate MOSFETs are used. The onsemi CS5160 datasheet explicitly targets high-density, high-speed logic. Keep the feedback traces short, place compensation close to the controller, and verify that switching ripple remains within the clock circuit's permitted noise budget.
推荐
Embedded Legacy Processor Board Repair
The CS5160GD is valuable for sustaining or repairing legacy CPU boards where the original controller footprint and voltage-program scheme must be preserved. Using the documented 16-pin PDSO footprint avoids a full board respin, while the 5-bit interface and dual-output capability support original processor power architectures. The onsemi CS5160 datasheet describes the part as a CPU controller designed for demanding logic systems. Repair work should include confirmation of the programming resistor values, MOSFET gate-drive waveforms, inductor saturation margin, and the operating conditions of any electrolytic output capacitors.
推荐
Dual-Rail Industrial Logic Supply
The CS5160GD can control two logic rails in an industrial controller or test system that retains legacy power-conversion requirements. Its 1.5 A rating, dual synchronous N-channel architecture, and 1000 kHz maximum switching frequency suit moderate-current, fast-transient digital supplies. According to the onsemi CS5160 datasheet, the controller was developed for high-density, high-speed logic rather than low-power energy harvesting. Designers should treat the aging controller status as a lifecycle issue and request availability confirmation before committing to new industrial production volumes.
推荐
CPU Voltage-Sequencing Reference Design
The CS5160GD can serve as the controller element in a legacy two-rail sequencing study because it provides two outputs for coordinated processor power delivery. The 5-bit control interface gives the designer more discrete adjustment positions, while the 1000 kHz switching capability supports fast transient correction. The onsemi CS5160 datasheet lists the device as an Intel Pentium II voltage-regulator controller, making it directly relevant to period-correct sequencing schemes. In a new board, replicate only the sequencing philosophy rather than assuming modern load-current, temperature, and reliability requirements are automatically met.
推荐
推荐产品汇总
工程参考数据: CS5160GD ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | CS5160GD16 |
|---|---|---|
| Brand | onsemi | onsemi |
| Package | 16-pin PDSO (SOIC-16) | 16-pin PDSO (SOIC-16) |
| Product Type | 5-bit synchronous buck controller | 5-bit synchronous buck controller |
| Number of Outputs | 2 outputs | 2 outputs |
| Output Current Rating | 1.5 A | 1.5 A |
| Maximum Switching Frequency | 1000 kHz | 1000 kHz |
| Control Mode | Current mode / voltage mode | Current mode / voltage mode |
| Topology | Dual N-channel synchronous buck | Dual N-channel synchronous buck |
| Primary Application | Intel Pentium II voltage regulation | Intel Pentium II voltage regulation |
| Ordering and Temperature Details | CS5160GD ordering code | CS5160GD16 ordering code; confirm grade in manufacturer documentation |
关键差异点
- Fine 5-bit voltage-programming resolution (对比 CS5160GD16)
- Dual synchronous N-channel outputs in one controller (对比 CS5160GD16)
- Fast-response CPU and high-speed logic positioning (对比 CS5160GD16)
设计说明
Place the controller, compensation components, and feedback components close to the associated power stage. Keep the high-current VIN, PHASE, and output-capacitor loops compact, and route sensitive feedback traces away from switching nodes. For a two-rail board, keep the two power-stage layouts symmetrical where possible because unequal parasitic inductance and loop area can change transient behavior even when the controller settings are identical.
The 1.5 A controller rating does not by itself establish the output-current capability of the assembled converter. That value also depends on the external high-side and low-side MOSFETs, inductor saturation current, copper paths, and output-capacitor ripple rating. Calculate worst-case dissipation across both MOSFETs and the inductor at maximum load and verify thermal margin using the actual PCB copper area and airflow conditions.
Do not substitute a different controller solely because it uses a 16-pin SOIC package. Compare the voltage-programming pin thresholds, feedback reference, compensation method, gate-drive timing, soft-start behavior, and output-current capability with the CS5160GD. For an existing motherboard, also verify the resistor values and capacitor polarities because a controller-level replacement cannot correct a legacy design with incorrect rail settings or aged storage components.
Treat the 1000 kHz switching capability as a design tool rather than a mandatory operating point. Select the actual frequency to balance transient response against MOSFET switching loss, inductor ripple current, and output-voltage ripple. Probe the feedback and output nodes with short ground springs and a suitable bandwidth-limited oscilloscope setup before and after compensation changes, since the controller's fast response can expose instability that is not obvious at low load.
合规信息
No specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals statement appears in the cited listings. The CS5160 is a legacy CPU controller and is treated as NRND for sourcing-planning purposes; request a manufacturer compliance declaration for the exact ordering code before production release.