DG412DVZ - Quad SPST CMOS Analog Switch | Renesas
料号: DG412DVZ ✓ 量产中DG412DVZ 概述
An analog switch is a semiconductor interface that connects or isolates circuit nodes under digital control. The DG412 belongs to the broader hierarchy of CMOS analog switches, multiplexer and demultiplexer devices, and signal-routing integrated circuits. Its four independent SPST channels allow separate control of four signal paths instead of forcing the designer to use one common multiplexer configuration. This makes the device suitable for analog measurement, test, communication, and control systems where independent routing is required.
The key verified features are four switch circuits, 1:1 signal routing, 35-ohm on resistance, normally open SPST construction, CMOS-compatible control, and a 16-pin TSSOP package. The normally open architecture keeps each switched path disconnected until its corresponding control input activates it. This behavior is useful when signal integrity, fault isolation, or predictable default states matter. The compact TSSOP outline also supports denser layouts than a larger through-hole package.
Renesas describes the DG412 family as monolithic CMOS analog switches with four independent SPST channels and TTL- and CMOS-compatible digital inputs. The DG412 series is positioned as a drop-in replacement for the earlier DG211 and DG212 device families. Its independent architecture separates each analog path while providing digital control from common logic systems, which is important in instrumentation and embedded test equipment.
Typical uses include signal isolation between a sensor and an analog-to-digital converter, channel selection in automated test systems, routing control signals between circuits, and disconnecting unused loads. In each case, the 35-ohm on resistance influences signal attenuation and drive requirements. Engineers should also verify the complete electrical limits and control timing from the manufacturer datasheet before operating signals near the device's specified limits.
PCB implementation requires care because analog switches can inject charge into high-impedance nodes and can respond to fast control-edge transients. Place the device close to the switched signal, provide a stable ground reference, and route control inputs away from sensitive analog traces. Avoid long unprotected control wires, and use the pin-description table in the manufacturer datasheet when assigning every TSSOP connection.
This page organizes the verified DG412DVZ product identity, package information, purchasing path, technical comparisons, and replacement guidance into one engineering-focused reference. It also identifies where application-specific electrical requirements must be checked against the DG411/DG412/DG413 datasheet before a board design is released for production.
直接替换替代料: DG412DVZ ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: DG412DVZ (相同外形与封装尺寸) ——差异在于 Mounting Type, Package, Switch Configuration.
DG412DVZ-T
✅ 直接替换📋 参考替代料(不在目录中)
DG411DVZ
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
DG411DVZ-T
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
DG412DVZ 最大额定值与电气特性
| Number of Switch Circuits | 4 circuits |
| Switch Configuration | 1:1 SPST |
| On Resistance | 35 ohms |
| Number of Terminals | 16 terminals |
| 封装 | 16-TSSOP |
| 安装类型 | Surface mount |
| Technology | CMOS |
| Control Compatibility | TTL-compatible and CMOS-compatible digital inputs |
| Default Contact State | Normally open |
| Channel Independence | 4 independent SPST switches |
| Temperature Grade | Industrial |
DG412DVZ 16-tssop 引脚配置指南
DG412DVZ(16-tssop 封装)的引脚配置。 引脚编号、功能和连接图在制造商数据手册中定义。请参阅该手册以了解确切的封装尺寸和焊接指南。
暂无详细引脚数据: DG412DVZ.
请参阅 数据手册 以查看完整引脚配置。
典型应用
DG412DVZ 适用于 6 应用s: Sensor Signal Isolation, ADC Channel Routing, Automated Test Systems, Communication Signal Routing, Battery-Powered Instrumentation, Control and Peripheral Routing.
Sensor Signal Isolation
The DG412DVZ fits sensor-interfaces that need several analog paths to be connected or disconnected independently. Its four normally open SPST switches prevent one sensor branch from disturbing another when inactive, while the 35-ohm on resistance provides a defined series impedance in the closed state. Place the switch close to the sensor interface and use the lowest-impedance return path available. Check leakage, charge injection, and off isolation against high-impedance sensor requirements in the Renesas datasheet.
推荐
ADC Channel Routing
DG412DVZ can route four independently controlled sources toward an analog-to-digital converter, allowing unused channels to remain disconnected from the conversion node. The 1:1 configuration preserves signal polarity, and the 35-ohm on resistance must be included when calculating divider ratios, source loading, and acquisition settling. For high-resolution conversions, verify injected charge, switch resistance matching, leakage, and switching timing from the manufacturer datasheet before selecting acquisition times.
推荐
Automated Test Systems
The four independent SPST channels make DG412DVZ useful in automated test equipment for connecting test stimuli to several nodes under digital control. Normally open contacts establish a defined disconnected state between measurements, reducing unwanted cross-connection. The 35-ohm on resistance affects drive level and sensing accuracy, so account for it in the test-path budget. Control timing also determines how quickly a new path may be trusted after switching.
推荐
Communication Signal Routing
DG412DVZ can provide independent connect and disconnect functions in low-speed communication equipment, especially where a transmitter, receiver, or termination network must be isolated during alternate operating modes. The 1:1 SPST topology does not reverse signal polarity, and the 35-ohm on resistance influences insertion loss and logic-level loading. Keep the analog traces short, provide a continuous ground reference, and verify whether control-edge transients require external filtering for the signal being routed.
推荐
Battery-Powered Instrumentation
The normally open DG412DVZ channels can disconnect loads and inactive circuit sections to reduce unintended current flow in battery-powered instruments. The four independent controls provide targeted isolation rather than shutting down an entire analog path at once. The 35-ohm on resistance should be evaluated for the maximum switched current and logic-level margin. Because switched nodes can transient when control inputs change, use clean control drive and confirm leakage behavior over the intended temperature range.
推荐
Control and Peripheral Routing
DG412DVZ can route or isolate control and peripheral signals between logic subsystems where four independent paths are more useful than a shared multiplexer. TTL- and CMOS-compatible digital inputs support integration with embedded logic, while the normally open state offers a predictable inactive condition. Keep control traces away from sensitive analog nets and use a solid ground reference to limit switching transients. Confirm the supply range, input thresholds, and timing from the manufacturer datasheet for the selected logic family.
推荐
推荐产品汇总
工程参考数据: DG412DVZ ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | DG412DVZ-T | DG411DVZ | DG411DVZ-T |
|---|---|---|---|---|
| Brand | Renesas Electronics | Renesas Electronics | Renesas Electronics | Renesas Electronics |
| Package | 16-TSSOP | 16-TSSOP | 16-TSSOP | 16-TSSOP |
| Number of Switch Circuits | 4 circuits | 4 circuits | 4 circuits | 4 circuits |
| Switch Configuration | 1:1 SPST | 1:1 SPST | SPST | SPST |
| Technology | CMOS | CMOS | CMOS | CMOS |
| Number of Terminals | 16 terminals | 16 terminals | 16 terminals | 16 terminals |
| Control Compatibility | TTL-compatible and CMOS-compatible digital inputs | TTL-compatible and CMOS-compatible digital inputs | TTL-compatible and CMOS-compatible digital inputs | TTL-compatible and CMOS-compatible digital inputs |
关键差异点
- Documented direct catalog alternative (对比 DG412DVZ-T)
- Independent four-channel routing (对比 DG411DVZ)
- Normally open default isolation (对比 DG411DVZ-T)
设计说明
Include the 35-ohm on resistance in the complete signal-path calculation for attenuation, logic-level margin, and output-current demand. For high-impedance receivers, also evaluate the switch leakage and off isolation specified in the manufacturer datasheet. Keep the switched node and its return path short, because long PCB traces add capacitance and can increase settling time after a control transition.
Place DG412DVZ near the signal source and receiver to minimize trace capacitance and coupling. Use the pin-description table in the Renesas datasheet to assign all 16 connections and connect the supply and ground pins to a low-impedance plane. Keep digital control routing away from sensitive analog nets, and provide a bypass capacitor close to the device when the application circuit requires local supply decoupling.
Do not treat a SPST switch as a multiplexer, and do not assume that a similarly named DG411 or DG413 device has identical behavior. Verify normally open versus normally closed contacts, control polarity, input thresholds, supply range, and timing before substituting. A footprint match alone does not establish functional drop-in compatibility, particularly when the design relies on a defined disconnected state.
合规信息
The DG412 catalog information identifies an industrial-grade device but does not establish the requested environmental or material compliance statuses. Confirm package-specific declarations with Renesas before production release.