DG412DVZ - Quad SPST CMOS Analog Switch | Renesas
부품 번호: DG412DVZ ✓ 활성DG412DVZ 개요
An analog switch is a semiconductor interface that connects or isolates circuit nodes under digital control. The DG412 belongs to the broader hierarchy of CMOS analog switches, multiplexer and demultiplexer devices, and signal-routing integrated circuits. Its four independent SPST channels allow separate control of four signal paths instead of forcing the designer to use one common multiplexer configuration. This makes the device suitable for analog measurement, test, communication, and control systems where independent routing is required.
The key verified features are four switch circuits, 1:1 signal routing, 35-ohm on resistance, normally open SPST construction, CMOS-compatible control, and a 16-pin TSSOP package. The normally open architecture keeps each switched path disconnected until its corresponding control input activates it. This behavior is useful when signal integrity, fault isolation, or predictable default states matter. The compact TSSOP outline also supports denser layouts than a larger through-hole package.
Renesas describes the DG412 family as monolithic CMOS analog switches with four independent SPST channels and TTL- and CMOS-compatible digital inputs. The DG412 series is positioned as a drop-in replacement for the earlier DG211 and DG212 device families. Its independent architecture separates each analog path while providing digital control from common logic systems, which is important in instrumentation and embedded test equipment.
Typical uses include signal isolation between a sensor and an analog-to-digital converter, channel selection in automated test systems, routing control signals between circuits, and disconnecting unused loads. In each case, the 35-ohm on resistance influences signal attenuation and drive requirements. Engineers should also verify the complete electrical limits and control timing from the manufacturer datasheet before operating signals near the device's specified limits.
PCB implementation requires care because analog switches can inject charge into high-impedance nodes and can respond to fast control-edge transients. Place the device close to the switched signal, provide a stable ground reference, and route control inputs away from sensitive analog traces. Avoid long unprotected control wires, and use the pin-description table in the manufacturer datasheet when assigning every TSSOP connection.
This page organizes the verified DG412DVZ product identity, package information, purchasing path, technical comparisons, and replacement guidance into one engineering-focused reference. It also identifies where application-specific electrical requirements must be checked against the DG411/DG412/DG413 datasheet before a board design is released for production.
드롭인 대체품: DG412DVZ — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: DG412DVZ (동일 폼 팩터 및 풋프린트) — 차이점: Mounting Type, Package, Switch Configuration.
DG412DVZ-T
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
DG411DVZ
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
DG411DVZ-T
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
DG412DVZ 최대 정격 & 전기적 특성
| Number of Switch Circuits | 4 circuits |
| Switch Configuration | 1:1 SPST |
| On Resistance | 35 ohms |
| Number of Terminals | 16 terminals |
| 패키지 | 16-TSSOP |
| 실장 유형 | Surface mount |
| Technology | CMOS |
| Control Compatibility | TTL-compatible and CMOS-compatible digital inputs |
| Default Contact State | Normally open |
| Channel Independence | 4 independent SPST switches |
| Temperature Grade | Industrial |
DG412DVZ 16-tssop 핀 구성 가이드
DG412DVZ(16-tssop 패키지)의 핀 구성입니다. 핀 번호, 기능, 연결 다이어그램은 제조사 데이터시트에 정의되어 있습니다. 정확한 풋프린트와 솔더링 지침은 해당 문서를 참조하십시오.
다음에 대한 상세 핀아웃 데이터 없음: DG412DVZ.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
DG412DVZ 적합 용도: 6 애플리케이션s: Sensor Signal Isolation, ADC Channel Routing, Automated Test Systems, Communication Signal Routing, Battery-Powered Instrumentation, Control and Peripheral Routing.
Sensor Signal Isolation
The DG412DVZ fits sensor-interfaces that need several analog paths to be connected or disconnected independently. Its four normally open SPST switches prevent one sensor branch from disturbing another when inactive, while the 35-ohm on resistance provides a defined series impedance in the closed state. Place the switch close to the sensor interface and use the lowest-impedance return path available. Check leakage, charge injection, and off isolation against high-impedance sensor requirements in the Renesas datasheet.
추천
ADC Channel Routing
DG412DVZ can route four independently controlled sources toward an analog-to-digital converter, allowing unused channels to remain disconnected from the conversion node. The 1:1 configuration preserves signal polarity, and the 35-ohm on resistance must be included when calculating divider ratios, source loading, and acquisition settling. For high-resolution conversions, verify injected charge, switch resistance matching, leakage, and switching timing from the manufacturer datasheet before selecting acquisition times.
추천
Automated Test Systems
The four independent SPST channels make DG412DVZ useful in automated test equipment for connecting test stimuli to several nodes under digital control. Normally open contacts establish a defined disconnected state between measurements, reducing unwanted cross-connection. The 35-ohm on resistance affects drive level and sensing accuracy, so account for it in the test-path budget. Control timing also determines how quickly a new path may be trusted after switching.
추천
Communication Signal Routing
DG412DVZ can provide independent connect and disconnect functions in low-speed communication equipment, especially where a transmitter, receiver, or termination network must be isolated during alternate operating modes. The 1:1 SPST topology does not reverse signal polarity, and the 35-ohm on resistance influences insertion loss and logic-level loading. Keep the analog traces short, provide a continuous ground reference, and verify whether control-edge transients require external filtering for the signal being routed.
추천
Battery-Powered Instrumentation
The normally open DG412DVZ channels can disconnect loads and inactive circuit sections to reduce unintended current flow in battery-powered instruments. The four independent controls provide targeted isolation rather than shutting down an entire analog path at once. The 35-ohm on resistance should be evaluated for the maximum switched current and logic-level margin. Because switched nodes can transient when control inputs change, use clean control drive and confirm leakage behavior over the intended temperature range.
추천
Control and Peripheral Routing
DG412DVZ can route or isolate control and peripheral signals between logic subsystems where four independent paths are more useful than a shared multiplexer. TTL- and CMOS-compatible digital inputs support integration with embedded logic, while the normally open state offers a predictable inactive condition. Keep control traces away from sensitive analog nets and use a solid ground reference to limit switching transients. Confirm the supply range, input thresholds, and timing from the manufacturer datasheet for the selected logic family.
추천
추천 제품 요약
엔지니어링 참조 데이터: DG412DVZ — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | DG412DVZ-T | DG411DVZ | DG411DVZ-T |
|---|---|---|---|---|
| Brand | Renesas Electronics | Renesas Electronics | Renesas Electronics | Renesas Electronics |
| Package | 16-TSSOP | 16-TSSOP | 16-TSSOP | 16-TSSOP |
| Number of Switch Circuits | 4 circuits | 4 circuits | 4 circuits | 4 circuits |
| Switch Configuration | 1:1 SPST | 1:1 SPST | SPST | SPST |
| Technology | CMOS | CMOS | CMOS | CMOS |
| Number of Terminals | 16 terminals | 16 terminals | 16 terminals | 16 terminals |
| Control Compatibility | TTL-compatible and CMOS-compatible digital inputs | TTL-compatible and CMOS-compatible digital inputs | TTL-compatible and CMOS-compatible digital inputs | TTL-compatible and CMOS-compatible digital inputs |
주요 차별점
- Documented direct catalog alternative (vs DG412DVZ-T)
- Independent four-channel routing (vs DG411DVZ)
- Normally open default isolation (vs DG411DVZ-T)
설계 노트
Include the 35-ohm on resistance in the complete signal-path calculation for attenuation, logic-level margin, and output-current demand. For high-impedance receivers, also evaluate the switch leakage and off isolation specified in the manufacturer datasheet. Keep the switched node and its return path short, because long PCB traces add capacitance and can increase settling time after a control transition.
Place DG412DVZ near the signal source and receiver to minimize trace capacitance and coupling. Use the pin-description table in the Renesas datasheet to assign all 16 connections and connect the supply and ground pins to a low-impedance plane. Keep digital control routing away from sensitive analog nets, and provide a bypass capacitor close to the device when the application circuit requires local supply decoupling.
Do not treat a SPST switch as a multiplexer, and do not assume that a similarly named DG411 or DG413 device has identical behavior. Verify normally open versus normally closed contacts, control polarity, input thresholds, supply range, and timing before substituting. A footprint match alone does not establish functional drop-in compatibility, particularly when the design relies on a defined disconnected state.
규정 준수 정보
The DG412 catalog information identifies an industrial-grade device but does not establish the requested environmental or material compliance statuses. Confirm package-specific declarations with Renesas before production release.