DS90C402MX/NOPB - Dual LVDS Receiver | Texas Instruments
料号: DS90C402MX/NOPB ✓ 量产中DS90C402MX/NOPB 概述
An LVDS receiver is an interface circuit that converts a small differential voltage into a compatible digital logic signal. LVDS belongs to the differential-signal interface family and is commonly positioned between a high-speed transmitter and downstream digital circuitry. The DS90C402 receiver works with the DS90C401 transmitter to form a complete high-speed point-to-point link. This architecture reduces signal amplitude while preserving noise immunity compared with many single-ended interfaces.
The DS90C402MX/NOPB provides a dual-receiver configuration in an 8-pin SOIC, allowing two data channels to share one device. Its 155.5 Mbps maximum data rate supports legacy point-to-point links that may appear in industrial control, telecommunications, test equipment, and embedded systems. A 4.5 V minimum supply supports 5 V interface designs, while the 5.5 V maximum accommodates standard 5 V supply tolerances.
The receiver's ±100 mV threshold sensitivity defines the differential signal amplitude required for reliable detection. Common-mode noise protection helps separate the intended differential signal from voltage disturbances shared by both conductors. Because LVDS depends on balanced routing and controlled termination, the receiver itself does not eliminate the need for proper PCB geometry, characteristic-impedance control, and connector or source termination.
Typical applications include dual-channel point-to-point backplanes, industrial data links, telecommunications equipment, instrumentation, and embedded control systems. The DS90C402 is especially appropriate when two receive channels are needed near one another and a compact 8-pin SOIC is preferred over larger receiver packages. Pairing it with the DS90C401 provides a matched transmitter and receiver solution for a bidirectional or paired communication path.
PCB layout should keep the LVDS traces short, continuous, and matched in geometry, with a solid ground plane providing the return path. Place termination components at the appropriate transmitter or receiver endpoint, and avoid stubs or test-point structures that create impedance discontinuities. Decoupling capacitors should connect directly to the device power and ground pins to minimize supply-loop inductance.
This page combines manufacturer specifications, ordering information, drop-in replacement guidance, comparison data, and practical interface-layout guidance. It supports faster component selection for engineers designing a 155.5 Mbps LVDS link while highlighting the electrical and package conditions required for true PCB-level substitution.
直接替换替代料: DS90C402MX/NOPB ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: DS90C402MX/NOPB (相同外形与封装尺寸) ——差异在于 Package, Operating Temperature Range, Number of Receivers.
DS90C402MX
✅ 直接替换联系询价
查看数据手册 →DS90C402M/NOPB
✅ 直接替换联系询价
查看数据手册 →DS90LV028AQMA/NOPB
✅ 直接替换📋 参考替代料(不在目录中)
DS90C402MX/NOPB 规格参数
| Receiver Type | Dual LVDS receiver |
| Number of Receivers | 2 channels |
| Number of Drivers | 0 channels |
| Maximum Data Rate | 155.5 Mbps |
| Supply Voltage Range | 4.5 V to 5.5 V |
| Differential Input Threshold | ±100 mV |
| Common-Mode Noise Protection | Supported |
| 封装 | 8-pin SOIC (D) |
| Package Body Width | 3.90 mm |
| Lead Pitch | 1.27 mm |
| 安装类型 | Surface mount |
| 工作温度范围 | -40 °C to +85 °C |
| Protocol | LVDS |
| Power Architecture | Low-power dual receiver |
| Signal Type | Low-voltage differential signaling |
| Shipping Packaging | Tape and reel |
| RoHS 状态 | Compliant |
DS90C402MX/NOPB 3.90 mm 引脚配置指南
DS90C402MX/NOPB(3.90 mm 封装)的引脚配置。 引脚编号、功能和连接图在制造商数据手册中定义。请参阅该手册以了解确切的封装尺寸和焊接指南。
暂无详细引脚数据: DS90C402MX/NOPB.
请参阅 数据手册 以查看完整引脚配置。
典型应用
DS90C402MX/NOPB 适用于 6 应用s: Industrial Point-to-Point Data Links, Telecommunications Backplanes, Test and Measurement Instrumentation, Embedded Control Communication, High-Speed Sensor and Data Acquisition, Legacy Computer and Peripheral Interfaces.
Industrial Point-to-Point Data Links
The DS90C402MX/NOPB fits industrial point-to-point links that require two receive channels at rates up to 155.5 Mbps. Its differential input threshold of ±100 mV and common-mode noise protection help distinguish the intended signal from disturbances encountered in industrial environments. The 4.5 V to 5.5 V supply range aligns with nominal 5 V logic, while the -40 °C to +85 °C rating covers a broad commercial operating range. Designers should use controlled-impedance routing, solid grounding, and endpoint termination to preserve the signal integrity expected from the LVDS interface.
推荐
Telecommunications Backplanes
The dual-receiver architecture of the DS90C402MX/NOPB supports compact telecommunications backplane interfaces where two low-power differential channels must be received near one another. Its 155.5 Mbps maximum data rate suits legacy high-speed point-to-point links, and common-mode noise protection assists operation in systems with substantial switching activity. An 8-pin SOIC can simplify routing compared with larger multi-channel receiver packages. Performance depends on maintaining controlled trace geometry, uninterrupted reference planes, and correct LVDS termination rather than on receiver selection alone.
推荐
Test and Measurement Instrumentation
The DS90C402MX/NOPB is appropriate for instrumentation that transfers differential data between a transmitter and a measurement or control subsystem. Two receiver channels can reduce package count, while the low-power design and ±100 mV threshold support compact signal-chain implementations. The 4.5 V to 5.5 V operating range permits use with conventional laboratory and embedded 5 V supplies. To preserve data integrity, keep the differential pair matched, route it over a continuous ground plane, and avoid adding unterminated branches that create reflections.
推荐
Embedded Control Communication
The DS90C402MX/NOPB can receive two differential data channels in an embedded control module that communicates with a nearby high-speed peripheral. Its 155.5 Mbps capability accommodates established LVDS links, while the small 8-pin SOIC supports space-conscious designs. The receiver operates across a -40 °C to +85 °C range and uses a conventional 5 V supply window. Firmware designers should define protocol timing around the device characteristics and validate propagation delay, input thresholds, and system-level clock tolerance during hardware integration.
推荐
High-Speed Sensor and Data Acquisition
The DS90C402MX/NOPB can form the receiving end of a compact differential sensor or data-acquisition link when the remote source includes a compatible LVDS transmitter. The two-channel configuration supports parallel or redundant channels, and the ±100 mV differential threshold provides a defined detection window. Its 155.5 Mbps maximum rate is suitable for many legacy high-rate acquisition paths. Signal-conditioning requirements, sensor settling time, cable or PCB loss, and endpoint termination must be evaluated together to avoid data errors outside the receiver's specified operating conditions.
推荐
Legacy Computer and Peripheral Interfaces
The DS90C402MX/NOPB is useful when maintaining or extending a legacy computer or peripheral interface that already uses 155.5 Mbps-class LVDS links. Two receivers can be placed in one 8-pin SOIC, reducing component count compared with separate single-channel receivers. The device accepts a 4.5 V to 5.5 V supply and provides common-mode noise protection for board-level communication. Because legacy links often use established connector and termination arrangements, engineers should retain the original characteristic-impedance geometry and verify signal polarity before replacing a receiver.
推荐
推荐产品汇总
工程参考数据: DS90C402MX/NOPB ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | DS90C402MX | DS90C402M/NOPB | DS90LV028AQMA/NOPB |
|---|---|---|---|---|
| Package | 8-pin SOIC (D) | 8-pin SOIC (D) | 8-pin SOIC | 8-pin SOP |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Receiver Count | 2 receivers | 2 receivers | 2 receivers | 2 receivers |
| Driver Count | 0 drivers | 0 drivers | 0 drivers | 0 drivers |
| Protocol | LVDS | LVDS | LVDS | LVDS |
| RoHS Ordering Designation | /NOPB, RoHS compliant | Non-/NOPB ordering option | /NOPB, RoHS compliant | /NOPB, RoHS compliant |
关键差异点
- Maintains the specified dual-channel LVDS performance (对比 DS90LV028AQMA/NOPB)
- Uses the lead-free RoHS-compliant ordering designation (对比 DS90C402MX)
- Combines two receivers with a 4.5 V to 5.5 V supply range (对比 DS90C402M/NOPB)
设计说明
Route the two LVDS differential pairs as coupled traces over a continuous ground plane, keeping their geometry and spacing uniform. Match the PCB fabrication characteristics of the intended LVDS interconnect and avoid changing layer transitions because a discontinuity can create reflections. Keep the receiver pins away from noisy clock and switching-node traces, and do not add test-point stubs unless their impedance effect has been evaluated.
Place the LVDS termination at the correct end of the link according to the system topology, normally at the receiving endpoint for a standard point-to-point interface. Confirm that the termination value matches the differential impedance used by the transmitter, board, and cable. The DS90C402MX/NOPB offers ±100 mV threshold sensitivity and common-mode protection, but neither feature compensates for incorrect termination or impedance mismatch.
Connect the device's supply and ground pins to a quiet 5 V rail with short, low-inductance traces and place the bypass capacitor directly beside the corresponding pins. Maintain a low-impedance ground return beneath the differential pairs. Decoupling placement is especially important in systems containing switching regulators because supply noise can couple into the receiver even when the differential data lines are routed carefully.
Do not substitute a receiver solely because both devices have eight pins and two channels. Verify differential polarity, supply levels, threshold voltage, propagation delay, maximum data rate, enable or fail-safe behavior, and termination requirements against the manufacturer datasheets. The DS90C402MX/NOPB is specified for 4.5 V to 5.5 V operation and 155.5 Mbps, so a same-package device with materially different timing or electrical limits may not be a functional drop-in.
合规信息
The /NOPB ordering option is identified as RoHS compliant. No separate REACH, halogen-free, conflict-minerals, or automotive qualification statement was identified.