DS90C402MX/NOPB - Dual LVDS Receiver | Texas Instruments
MPN: DS90C402MX/NOPB ✓ فعالDS90C402MX/NOPB نمای کلی
An LVDS receiver is an interface circuit that converts a small differential voltage into a compatible digital logic signal. LVDS belongs to the differential-signal interface family and is commonly positioned between a high-speed transmitter and downstream digital circuitry. The DS90C402 receiver works with the DS90C401 transmitter to form a complete high-speed point-to-point link. This architecture reduces signal amplitude while preserving noise immunity compared with many single-ended interfaces.
The DS90C402MX/NOPB provides a dual-receiver configuration in an 8-pin SOIC, allowing two data channels to share one device. Its 155.5 Mbps maximum data rate supports legacy point-to-point links that may appear in industrial control, telecommunications, test equipment, and embedded systems. A 4.5 V minimum supply supports 5 V interface designs, while the 5.5 V maximum accommodates standard 5 V supply tolerances.
The receiver's ±100 mV threshold sensitivity defines the differential signal amplitude required for reliable detection. Common-mode noise protection helps separate the intended differential signal from voltage disturbances shared by both conductors. Because LVDS depends on balanced routing and controlled termination, the receiver itself does not eliminate the need for proper PCB geometry, characteristic-impedance control, and connector or source termination.
Typical applications include dual-channel point-to-point backplanes, industrial data links, telecommunications equipment, instrumentation, and embedded control systems. The DS90C402 is especially appropriate when two receive channels are needed near one another and a compact 8-pin SOIC is preferred over larger receiver packages. Pairing it with the DS90C401 provides a matched transmitter and receiver solution for a bidirectional or paired communication path.
PCB layout should keep the LVDS traces short, continuous, and matched in geometry, with a solid ground plane providing the return path. Place termination components at the appropriate transmitter or receiver endpoint, and avoid stubs or test-point structures that create impedance discontinuities. Decoupling capacitors should connect directly to the device power and ground pins to minimize supply-loop inductance.
This page combines manufacturer specifications, ordering information, drop-in replacement guidance, comparison data, and practical interface-layout guidance. It supports faster component selection for engineers designing a 155.5 Mbps LVDS link while highlighting the electrical and package conditions required for true PCB-level substitution.
جایگزینهای drop-in برای DS90C402MX/NOPB — همان پکیج، سازگار پینبهپین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.
گونهها در این سری
مدلهای همسری که جایگزین مستقیم هستند برای DS90C402MX/NOPB (همان فرمفاکتور و فوتپرینت) — متفاوت در Package, Operating Temperature Range, Number of Receivers.
DS90C402MX
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←DS90C402M/NOPB
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←DS90LV028AQMA/NOPB
✅ جایگزین مستقیم📋 جایگزین مرجع (خارج از کاتالوگ)
DS90C402MX/NOPB مشخصات
| Receiver Type | Dual LVDS receiver |
| Number of Receivers | 2 channels |
| Number of Drivers | 0 channels |
| Maximum Data Rate | 155.5 Mbps |
| Supply Voltage Range | 4.5 V to 5.5 V |
| Differential Input Threshold | ±100 mV |
| Common-Mode Noise Protection | Supported |
| بستهبندی | 8-pin SOIC (D) |
| Package Body Width | 3.90 mm |
| Lead Pitch | 1.27 mm |
| نوع نصب | Surface mount |
| محدوده دمای کاری | -40 °C to +85 °C |
| Protocol | LVDS |
| Power Architecture | Low-power dual receiver |
| Signal Type | Low-voltage differential signaling |
| Shipping Packaging | Tape and reel |
| وضعیت RoHS | Compliant |
راهنمای پیکربندی پین DS90C402MX/NOPB 3.90 mm
پیکربندی پین برای DS90C402MX/NOPB (پکیج 3.90 mm). شمارهگذاری پایهها، عملکردها و نمودارهای اتصال در دیتاشیت سازنده تعریف شده است. برای footprint دقیق و دستورالعملهای لحیمکاری به آن مراجعه کنید.
داده پینآوت تفصیلی موجود نیست برای DS90C402MX/NOPB.
به دیتاشیت برای پیکربندی کامل پینها.
کاربردهای معمول
DS90C402MX/NOPB مناسب است برای 6 کاربردs: Industrial Point-to-Point Data Links, Telecommunications Backplanes, Test and Measurement Instrumentation, Embedded Control Communication, High-Speed Sensor and Data Acquisition, Legacy Computer and Peripheral Interfaces.
Industrial Point-to-Point Data Links
The DS90C402MX/NOPB fits industrial point-to-point links that require two receive channels at rates up to 155.5 Mbps. Its differential input threshold of ±100 mV and common-mode noise protection help distinguish the intended signal from disturbances encountered in industrial environments. The 4.5 V to 5.5 V supply range aligns with nominal 5 V logic, while the -40 °C to +85 °C rating covers a broad commercial operating range. Designers should use controlled-impedance routing, solid grounding, and endpoint termination to preserve the signal integrity expected from the LVDS interface.
پیشنهادی
Telecommunications Backplanes
The dual-receiver architecture of the DS90C402MX/NOPB supports compact telecommunications backplane interfaces where two low-power differential channels must be received near one another. Its 155.5 Mbps maximum data rate suits legacy high-speed point-to-point links, and common-mode noise protection assists operation in systems with substantial switching activity. An 8-pin SOIC can simplify routing compared with larger multi-channel receiver packages. Performance depends on maintaining controlled trace geometry, uninterrupted reference planes, and correct LVDS termination rather than on receiver selection alone.
پیشنهادی
Test and Measurement Instrumentation
The DS90C402MX/NOPB is appropriate for instrumentation that transfers differential data between a transmitter and a measurement or control subsystem. Two receiver channels can reduce package count, while the low-power design and ±100 mV threshold support compact signal-chain implementations. The 4.5 V to 5.5 V operating range permits use with conventional laboratory and embedded 5 V supplies. To preserve data integrity, keep the differential pair matched, route it over a continuous ground plane, and avoid adding unterminated branches that create reflections.
پیشنهادی
Embedded Control Communication
The DS90C402MX/NOPB can receive two differential data channels in an embedded control module that communicates with a nearby high-speed peripheral. Its 155.5 Mbps capability accommodates established LVDS links, while the small 8-pin SOIC supports space-conscious designs. The receiver operates across a -40 °C to +85 °C range and uses a conventional 5 V supply window. Firmware designers should define protocol timing around the device characteristics and validate propagation delay, input thresholds, and system-level clock tolerance during hardware integration.
پیشنهادی
High-Speed Sensor and Data Acquisition
The DS90C402MX/NOPB can form the receiving end of a compact differential sensor or data-acquisition link when the remote source includes a compatible LVDS transmitter. The two-channel configuration supports parallel or redundant channels, and the ±100 mV differential threshold provides a defined detection window. Its 155.5 Mbps maximum rate is suitable for many legacy high-rate acquisition paths. Signal-conditioning requirements, sensor settling time, cable or PCB loss, and endpoint termination must be evaluated together to avoid data errors outside the receiver's specified operating conditions.
پیشنهادی
Legacy Computer and Peripheral Interfaces
The DS90C402MX/NOPB is useful when maintaining or extending a legacy computer or peripheral interface that already uses 155.5 Mbps-class LVDS links. Two receivers can be placed in one 8-pin SOIC, reducing component count compared with separate single-channel receivers. The device accepts a 4.5 V to 5.5 V supply and provides common-mode noise protection for board-level communication. Because legacy links often use established connector and termination arrangements, engineers should retain the original characteristic-impedance geometry and verify signal polarity before replacing a receiver.
پیشنهادی
خلاصه محصولات پیشنهادی
دادههای مرجع مهندسی برای DS90C402MX/NOPB — مقایسه، راهنمای طراحی و اطلاعات انطباق.
راهنمای انتخاب
مقایسه با جایگزینها
| پارامتر | این محصول | DS90C402MX | DS90C402M/NOPB | DS90LV028AQMA/NOPB |
|---|---|---|---|---|
| Package | 8-pin SOIC (D) | 8-pin SOIC (D) | 8-pin SOIC | 8-pin SOP |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Receiver Count | 2 receivers | 2 receivers | 2 receivers | 2 receivers |
| Driver Count | 0 drivers | 0 drivers | 0 drivers | 0 drivers |
| Protocol | LVDS | LVDS | LVDS | LVDS |
| RoHS Ordering Designation | /NOPB, RoHS compliant | Non-/NOPB ordering option | /NOPB, RoHS compliant | /NOPB, RoHS compliant |
تفاوتهای کلیدی
- Maintains the specified dual-channel LVDS performance (در مقابلDS90LV028AQMA/NOPB)
- Uses the lead-free RoHS-compliant ordering designation (در مقابلDS90C402MX)
- Combines two receivers with a 4.5 V to 5.5 V supply range (در مقابلDS90C402M/NOPB)
یادداشتهای طراحی
Route the two LVDS differential pairs as coupled traces over a continuous ground plane, keeping their geometry and spacing uniform. Match the PCB fabrication characteristics of the intended LVDS interconnect and avoid changing layer transitions because a discontinuity can create reflections. Keep the receiver pins away from noisy clock and switching-node traces, and do not add test-point stubs unless their impedance effect has been evaluated.
Place the LVDS termination at the correct end of the link according to the system topology, normally at the receiving endpoint for a standard point-to-point interface. Confirm that the termination value matches the differential impedance used by the transmitter, board, and cable. The DS90C402MX/NOPB offers ±100 mV threshold sensitivity and common-mode protection, but neither feature compensates for incorrect termination or impedance mismatch.
Connect the device's supply and ground pins to a quiet 5 V rail with short, low-inductance traces and place the bypass capacitor directly beside the corresponding pins. Maintain a low-impedance ground return beneath the differential pairs. Decoupling placement is especially important in systems containing switching regulators because supply noise can couple into the receiver even when the differential data lines are routed carefully.
Do not substitute a receiver solely because both devices have eight pins and two channels. Verify differential polarity, supply levels, threshold voltage, propagation delay, maximum data rate, enable or fail-safe behavior, and termination requirements against the manufacturer datasheets. The DS90C402MX/NOPB is specified for 4.5 V to 5.5 V operation and 155.5 Mbps, so a same-package device with materially different timing or electrical limits may not be a functional drop-in.
اطلاعات انطباق
The /NOPB ordering option is identified as RoHS compliant. No separate REACH, halogen-free, conflict-minerals, or automotive qualification statement was identified.