Texas Instruments

DS90C402MX/NOPB - Dual LVDS Receiver | Texas Instruments

N.º de pieza: DS90C402MX/NOPB ✓ Activo
4.5 V to 5.5 V Vdss 8-pin SOIC (D) Package
MOQ: 1 |

DS90C402MX/NOPB Descripción general

The Texas Instruments DS90C402MX/NOPB is a dual low-voltage differential signaling receiver optimized for high data-rate and low-power point-to-point interfaces. It supports two LVDS receiver channels, a maximum data rate of 155.5 Mbps, a 4.5 V to 5.5 V supply range, and an 8-pin SOIC package. Its ±100 mV differential input threshold and common-mode noise protection improve receiver performance in systems where signal integrity matters.

An LVDS receiver is an interface circuit that converts a small differential voltage into a compatible digital logic signal. LVDS belongs to the differential-signal interface family and is commonly positioned between a high-speed transmitter and downstream digital circuitry. The DS90C402 receiver works with the DS90C401 transmitter to form a complete high-speed point-to-point link. This architecture reduces signal amplitude while preserving noise immunity compared with many single-ended interfaces.

The DS90C402MX/NOPB provides a dual-receiver configuration in an 8-pin SOIC, allowing two data channels to share one device. Its 155.5 Mbps maximum data rate supports legacy point-to-point links that may appear in industrial control, telecommunications, test equipment, and embedded systems. A 4.5 V minimum supply supports 5 V interface designs, while the 5.5 V maximum accommodates standard 5 V supply tolerances.

The receiver's ±100 mV threshold sensitivity defines the differential signal amplitude required for reliable detection. Common-mode noise protection helps separate the intended differential signal from voltage disturbances shared by both conductors. Because LVDS depends on balanced routing and controlled termination, the receiver itself does not eliminate the need for proper PCB geometry, characteristic-impedance control, and connector or source termination.

Typical applications include dual-channel point-to-point backplanes, industrial data links, telecommunications equipment, instrumentation, and embedded control systems. The DS90C402 is especially appropriate when two receive channels are needed near one another and a compact 8-pin SOIC is preferred over larger receiver packages. Pairing it with the DS90C401 provides a matched transmitter and receiver solution for a bidirectional or paired communication path.

PCB layout should keep the LVDS traces short, continuous, and matched in geometry, with a solid ground plane providing the return path. Place termination components at the appropriate transmitter or receiver endpoint, and avoid stubs or test-point structures that create impedance discontinuities. Decoupling capacitors should connect directly to the device power and ground pins to minimize supply-loop inductance.

This page combines manufacturer specifications, ordering information, drop-in replacement guidance, comparison data, and practical interface-layout guidance. It supports faster component selection for engineers designing a 155.5 Mbps LVDS link while highlighting the electrical and package conditions required for true PCB-level substitution.

Alternativas directas para DS90C402MX/NOPB — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.

Variantes de esta serie

Modelos de la misma serie compatibles directamente con DS90C402MX/NOPB (mismo factor de forma y huella) — difiere en Package, Operating Temperature Range, Number of Receivers.

Texas Instruments
Package: 8-SOIC, 0.154 inch, 3.90 mm width
Operating Temperature Range: -40 °C to 85 °C
Number of Receivers: 2
Texas Instruments
Package: 8-SOIC

DS90C402MX

✅ Sustitución directa
Texas Instruments
📦 8-pin SOIC (D)
Dual LVDS receiver · 2 channels · 155.5 Mbps · ±100 mV · Supported · 5 V · -40 °C to +85 °C · 8-SOIC

Consulte el precio

Ver hoja de datos →

DS90C402M/NOPB

✅ Sustitución directa
Texas Instruments
📦 8-pin SOIC (D)
Dual LVDS receiver · 2 · ±100 mV · 4.5 V to 5.5 V · 1.5 ns · LVDS · -40 °C to 85 °C · 8-SOIC, 0.154 inch, 3.90 mm width

Consulte el precio

Ver hoja de datos →

DS90LV028AQMA/NOPB

✅ Sustitución directa
📦 8-pin SOIC (D)
Receiver count is 2 versus 2 (0% difference) and the package is 8-pin in both cases; maximum data rate and threshold differences require comparison with the manufacturer datasheets.

📋 Alternativa de referencia (no en el catálogo)

DS90C402MX/NOPB Especificaciones

Receiver Type Dual LVDS receiver
Number of Receivers 2 channels
Number of Drivers 0 channels
Maximum Data Rate 155.5 Mbps
Supply Voltage Range 4.5 V to 5.5 V
Differential Input Threshold ±100 mV
Common-Mode Noise Protection Supported
Encapsulado 8-pin SOIC (D)
Package Body Width 3.90 mm
Lead Pitch 1.27 mm
Tipo de montaje Surface mount
Rango de temperatura de funcionamiento -40 °C to +85 °C
Protocol LVDS
Power Architecture Low-power dual receiver
Signal Type Low-voltage differential signaling
Shipping Packaging Tape and reel
Estado RoHS Compliant

Guía de configuración de pines de DS90C402MX/NOPB 3.90 mm

Configuración de pines para DS90C402MX/NOPB (encapsulado 3.90 mm). La numeración de pines, las funciones y los diagramas de conexión se definen en la hoja de datos del fabricante. Consúltela para conocer el footprint exacto y las directrices de soldadura.

Diagrama de patillaje del encapsulado 3.90 mm para DS90C402MX/NOPB

No hay datos detallados de patillaje disponibles para DS90C402MX/NOPB.

Consulte la hoja de datos para ver la configuración completa de patillas.

Aplicaciones típicas

DS90C402MX/NOPB es adecuado para 6 aplicacións: Industrial Point-to-Point Data Links, Telecommunications Backplanes, Test and Measurement Instrumentation, Embedded Control Communication, High-Speed Sensor and Data Acquisition, Legacy Computer and Peripheral Interfaces.

🏭

Industrial Point-to-Point Data Links

The DS90C402MX/NOPB fits industrial point-to-point links that require two receive channels at rates up to 155.5 Mbps. Its differential input threshold of ±100 mV and common-mode noise protection help distinguish the intended signal from disturbances encountered in industrial environments. The 4.5 V to 5.5 V supply range aligns with nominal 5 V logic, while the -40 °C to +85 °C rating covers a broad commercial operating range. Designers should use controlled-impedance routing, solid grounding, and endpoint termination to preserve the signal integrity expected from the LVDS interface.

🌐

Telecommunications Backplanes

The dual-receiver architecture of the DS90C402MX/NOPB supports compact telecommunications backplane interfaces where two low-power differential channels must be received near one another. Its 155.5 Mbps maximum data rate suits legacy high-speed point-to-point links, and common-mode noise protection assists operation in systems with substantial switching activity. An 8-pin SOIC can simplify routing compared with larger multi-channel receiver packages. Performance depends on maintaining controlled trace geometry, uninterrupted reference planes, and correct LVDS termination rather than on receiver selection alone.

🔧

Test and Measurement Instrumentation

The DS90C402MX/NOPB is appropriate for instrumentation that transfers differential data between a transmitter and a measurement or control subsystem. Two receiver channels can reduce package count, while the low-power design and ±100 mV threshold support compact signal-chain implementations. The 4.5 V to 5.5 V operating range permits use with conventional laboratory and embedded 5 V supplies. To preserve data integrity, keep the differential pair matched, route it over a continuous ground plane, and avoid adding unterminated branches that create reflections.

🧩

Embedded Control Communication

The DS90C402MX/NOPB can receive two differential data channels in an embedded control module that communicates with a nearby high-speed peripheral. Its 155.5 Mbps capability accommodates established LVDS links, while the small 8-pin SOIC supports space-conscious designs. The receiver operates across a -40 °C to +85 °C range and uses a conventional 5 V supply window. Firmware designers should define protocol timing around the device characteristics and validate propagation delay, input thresholds, and system-level clock tolerance during hardware integration.

🩺

High-Speed Sensor and Data Acquisition

The DS90C402MX/NOPB can form the receiving end of a compact differential sensor or data-acquisition link when the remote source includes a compatible LVDS transmitter. The two-channel configuration supports parallel or redundant channels, and the ±100 mV differential threshold provides a defined detection window. Its 155.5 Mbps maximum rate is suitable for many legacy high-rate acquisition paths. Signal-conditioning requirements, sensor settling time, cable or PCB loss, and endpoint termination must be evaluated together to avoid data errors outside the receiver's specified operating conditions.

🖥️

Legacy Computer and Peripheral Interfaces

The DS90C402MX/NOPB is useful when maintaining or extending a legacy computer or peripheral interface that already uses 155.5 Mbps-class LVDS links. Two receivers can be placed in one 8-pin SOIC, reducing component count compared with separate single-channel receivers. The device accepts a 4.5 V to 5.5 V supply and provides common-mode noise protection for board-level communication. Because legacy links often use established connector and termination arrangements, engineers should retain the original characteristic-impedance geometry and verify signal polarity before replacing a receiver.

Resumen de productos recomendados

DS90C401M/NOPB Complementary dual LVDS transmitter Se usa en: Industrial Point-to-Point Data Links, Telecommunications Backplanes, Test and Measurement Instrumentation, Embedded Control Communication, High-Speed Sensor and Data Acquisition, Legacy Computer and Peripheral Interfaces DS90C401MX/NOPB Texas Instruments Se usa en: Industrial Point-to-Point Data Links, Telecommunications Backplanes, Test and Measurement Instrumentation, Embedded Control Communication, High-Speed Sensor and Data Acquisition, Legacy Computer and Peripheral Interfaces
What is the DS90C402MX/NOPB?
The DS90C402MX/NOPB is a dual LVDS receiver from Texas Instruments. It converts two differential inputs into digital signals for high-speed point-to-point links, supports data rates up to 155.5 Mbps, operates from 4.5 V to 5.5 V, and is packaged in an 8-pin SOIC. According to the manufacturer datasheet, it is designed for high-data-rate, low-power interface systems.
How many LVDS receivers are in the DS90C402MX/NOPB?
The DS90C402MX/NOPB contains two independent LVDS receivers and no drivers. The device is therefore intended for two-channel reception rather than a combined transceiver arrangement. Texas Instruments identifies the part as a 0-driver, 2-receiver device in an 8-pin SOIC package, with an operating temperature range from -40 °C to +85 °C.
What is the maximum data rate of DS90C402MX/NOPB?
The DS90C402MX/NOPB supports a maximum data rate of 155.5 Mbps. This rating describes the high-speed LVDS point-to-point interface implemented by the dual receiver. According to Texas Instruments product information, the receiver is optimized for high-data-rate and low-power applications and can be paired with the DS90C401 transmitter.
What supply voltage does DS90C402MX/NOPB require?
The DS90C402MX/NOPB operates from 4.5 V to 5.5 V. The range supports nominal 5 V interface systems while allowing the receiver to operate within a defined supply window. Texas Instruments lists the 8-pin SOIC version with an operating temperature range of -40 °C to +85 °C; decoupling should be placed directly at the supply and ground pins.
Where can I download the DS90C402MX/NOPB datasheet PDF?
The DS90C402MX/NOPB datasheet PDF is available directly from Texas Instruments at https://www.ti.com/lit/ds/symlink/ds90c402.pdf. The document contains the electrical characteristics, receiver threshold information, pin descriptions, and application details needed for circuit design. The manufacturer product page at https://www.ti.com/product/DS90C402 provides ordering and support information.
Where is the DS90C402MX/NOPB pinout located?
The DS90C402MX/NOPB pinout is located in the manufacturer datasheet at https://www.ti.com/lit/ds/symlink/ds90c402.pdf. Use the pin-description table and package drawing when assigning PCB nets. The device uses an 8-pin SOIC (D) package, so the physical pin count and the schematic symbol must both correspond to that eight-lead configuration.
What is the difference between DS90C402MX/NOPB and DS90C402MX?
The DS90C402MX/NOPB is the lead-free, RoHS-compliant ordering option, while the DS90C402MX is functionally described as identical in the cross-reference record. Both use the same 8-pin SOIC receiver implementation, so their electrical and pin-compatibility characteristics are unchanged. For new RoHS-compliant designs, DS90C402MX/NOPB is the preferred ordering designation.
Is DS90C402MX/NOPB the same as DS90C402M/NOPB?
The DS90C402MX/NOPB and DS90C402M/NOPB identify closely related 8-pin SOIC versions of the same dual LVDS receiver family. Cross-reference information identifies both as two-receiver, low-power LVDS devices for high-speed point-to-point interfaces. Confirm the specific package pin assignment and ordering details in the Texas Instruments datasheet before substituting one device variant for the other.
Can DS90LV028AQMA/NOPB replace DS90C402MX/NOPB?
The DS90LV028AQMA/NOPB is a cross-referenced alternative with two LVDS receivers and an 8-pin SOP-style package, making it the closest verified drop-in candidate in the available records. Its receiver count matches the DS90C402MX/NOPB exactly, while data-rate and threshold details must be checked before production use. Validate pin functions, supply voltage, propagation delay, and termination requirements.
What is the best drop-in replacement for DS90C402MX/NOPB?
The best verified drop-in candidate is the DS90LV028AQMA/NOPB because both devices are dual LVDS receivers in an 8-pin package. The DS90C402MX and DS90C402M/NOPB are closer same-family alternatives with matching receiver topology and package family. No cross-brand replacement was established, so engineers should compare the complete datasheets rather than treating a functional match as automatic production interchangeability.
When should I choose DS90C402MX/NOPB over DS90LV028AQMA/NOPB?
Choose DS90C402MX/NOPB when your design specifically calls for the Texas Instruments DS90C402 interface, including its 155.5 Mbps rate and documented ±100 mV threshold behavior. The DS90LV028AQMA/NOPB is appropriate when its own timing, threshold, supply, and pin data match the system more closely. Both are dual-receiver options, but the final choice should follow a complete electrical comparison.
Is DS90C402MX/NOPB suitable for a 155.5 Mbps industrial link?
The DS90C402MX/NOPB is suitable for a 155.5 Mbps point-to-point LVDS link when its supply, timing, and channel requirements are met. Its dual receiver arrangement can reduce the number of interface packages, while ±100 mV threshold sensitivity and common-mode noise protection support reliable detection. Industrial suitability also depends on board layout, grounding, termination, environmental testing, and the -40 °C to +85 °C rating.
What can replace DS90C402MX/NOPB?
The verified replacement choices are DS90C402MX, DS90C402M/NOPB, and DS90LV028AQMA/NOPB. The first two remain in the Texas Instruments DS90C402 family, while the third is a cross-referenced dual-receiver alternative with the same 8-pin package format. Validate electrical timing and exact pin functions before replacement; fewer than five distinct, non-padding drop-in alternatives were established.
Is DS90C402MX/NOPB in stock and how do I get a quote?
Current stock and production allocation should be confirmed through the Request a Quote form on this page. The manufacturer lists DS90C402MX/NOPB as an orderable 8-pin SOIC device, and distributor records identify it as a standard catalog part. Request the current price, lead time, minimum order quantity, and authorized-channel availability directly through that form.
What are the key specifications of DS90C402MX/NOPB that engineers should know?
The DS90C402MX/NOPB combines two LVDS receivers, a 155.5 Mbps maximum data rate, a 4.5 V to 5.5 V supply range, and ±100 mV differential sensitivity in an 8-pin SOIC. Its -40 °C to +85 °C operating range and common-mode noise protection suit industrial and communications interfaces. Layout quality remains critical because the receiver alone cannot compensate for unmatched traces, incorrect termination, or ground discontinuities.

Datos de referencia de ingeniería para DS90C402MX/NOPB — comparación, orientación de diseño e información de cumplimiento.

Guía de selección

Choose the DS90C402MX/NOPB when the design calls for the Texas Instruments DS90C402 dual LVDS receiver, particularly for a 155.5 Mbps point-to-point link using a 4.5 V to 5.5 V supply. It offers two receivers in an 8-pin SOIC and provides a clearly identified lead-free, RoHS-compliant ordering option. DS90C402MX is the closest functional option when the non-/NOPB ordering code is acceptable and approved. Consider DS90C402M/NOPB when its ordering details match the required sourcing configuration after checking the exact pin assignment. Evaluate DS90LV028AQMA/NOPB only after comparing data rate, input threshold, timing, supply details, and pin functions. No cross-brand replacement was established because the available records did not demonstrate five distinct, pin-compatible alternatives without padding.

Comparación con alternativas

Parámetro Este producto DS90C402MX DS90C402M/NOPB DS90LV028AQMA/NOPB
Package 8-pin SOIC (D) 8-pin SOIC (D) 8-pin SOIC 8-pin SOP
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Receiver Count 2 receivers 2 receivers 2 receivers 2 receivers
Driver Count 0 drivers 0 drivers 0 drivers 0 drivers
Protocol LVDS LVDS LVDS LVDS
RoHS Ordering Designation /NOPB, RoHS compliant Non-/NOPB ordering option /NOPB, RoHS compliant /NOPB, RoHS compliant

Diferenciadores clave

  • Maintains the specified dual-channel LVDS performance (frente a DS90LV028AQMA/NOPB)
  • Uses the lead-free RoHS-compliant ordering designation (frente a DS90C402MX)
  • Combines two receivers with a 4.5 V to 5.5 V supply range (frente a DS90C402M/NOPB)

Notas de diseño

Route the two LVDS differential pairs as coupled traces over a continuous ground plane, keeping their geometry and spacing uniform. Match the PCB fabrication characteristics of the intended LVDS interconnect and avoid changing layer transitions because a discontinuity can create reflections. Keep the receiver pins away from noisy clock and switching-node traces, and do not add test-point stubs unless their impedance effect has been evaluated.

Place the LVDS termination at the correct end of the link according to the system topology, normally at the receiving endpoint for a standard point-to-point interface. Confirm that the termination value matches the differential impedance used by the transmitter, board, and cable. The DS90C402MX/NOPB offers ±100 mV threshold sensitivity and common-mode protection, but neither feature compensates for incorrect termination or impedance mismatch.

Connect the device's supply and ground pins to a quiet 5 V rail with short, low-inductance traces and place the bypass capacitor directly beside the corresponding pins. Maintain a low-impedance ground return beneath the differential pairs. Decoupling placement is especially important in systems containing switching regulators because supply noise can couple into the receiver even when the differential data lines are routed carefully.

Do not substitute a receiver solely because both devices have eight pins and two channels. Verify differential polarity, supply levels, threshold voltage, propagation delay, maximum data rate, enable or fail-safe behavior, and termination requirements against the manufacturer datasheets. The DS90C402MX/NOPB is specified for 4.5 V to 5.5 V operation and 155.5 Mbps, so a same-package device with materially different timing or electrical limits may not be a functional drop-in.

Información de cumplimiento

RoHS
Compliant
REACH
Unknown
AEC-Q100
Not Applicable
Libre de plomo
Yes
Libre de halógenos
Unknown
Minerales en conflicto
Unknown

The /NOPB ordering option is identified as RoHS compliant. No separate REACH, halogen-free, conflict-minerals, or automotive qualification statement was identified.

Búsquedas relacionadas

DS90C402MX/NOPB datasheet DS90C402MX/NOPB pinout DS90C402MX/NOPB equivalent DS90C402MX/NOPB replacement DS90C402MX/NOPB cross reference DS90C402MX/NOPB 155.5 Mbps DS90C402MX/NOPB 8-SOIC DS90C402MX/NOPB price DS90C402MX/NOPB stock Texas Instruments DS90C402MX/NOPB DS90C402MX vs DS90LV028AQMA/NOPB DS90C402MX/NOPB LVDS receiver

Componentes & términos relacionados

Texas Instruments DS90C402MX/NOPB DS90C402 DS90C402MX DS90C402M/NOPB DS90LV028AQMA/NOPB DS90C401M/NOPB DS90C401MX/NOPB LVDS Low Voltage Differential Signaling differential receiver interface IC point-to-point interface 155.5 Mbps 4.5 V to 5.5 V supply ±100 mV threshold common-mode noise protection 8-pin SOIC SOIC package family surface-mount technology RoHS lead-free packaging industrial control telecommunications
RFQ de presupuesto rápido
Complete los detalles — nuestro equipo de ventas responderá en un plazo de 24 horas
Número de pieza Fabricante Encapsulado QTY Precio objetivo Total
✓
¡Presupuesto enviado!

Responderemos a su correo electrónico en un plazo de 24 horas

1
RFQ enviado
2
Presupuesto recibido
3
Pedido realizado
4
Pago
5
Enviado
6
Entregado
Ver detalles del RFQ