DS90LV001TMX - 800 Mbps LVDS Buffer | Texas Instruments
料号: DS90LV001TMX ✗ 停产DS90LV001TMX 概述
An LVDS buffer is a digital interface component in the LVDS interface IC family. LVDS, or Low-Voltage Differential Signaling, uses low-amplitude differential voltage to transmit high-speed data with common-mode noise rejection and reduced electromagnetic emissions. A buffer placed in the signal path can extend usable distribution distance, isolate a transmitter from capacitive loading, and reduce the effect of imperfect terminations. The DS90LV001 family is therefore positioned between an LVDS transmitter and downstream LVDS receivers within the broader interface IC and semiconductor hierarchy.
The principal electrical characteristic is an 800-Mbps data rate, suitable for high-speed backplane links, industrial control systems, communications equipment, and test platforms. The verified distributor description identifies the DS90LV001TMX as a single-channel LVDS buffer in an 8-SOIC package with an industrial temperature range from -40°C to +85°C. The output-enable pin allows the output to be disabled for bus sharing, controlled test modes, power-management schemes, or designs that need a high-impedance state during transitions.
The device is designed to address signal-conditioning problems caused by transmission-line reflections, loading, and stub length. In large systems, the distance between a transmission line and an unterminated receiver on an individual card can limit system speed. A dedicated LVDS buffer can be placed near the receiver or at a card boundary to create a controlled signal path. Designers must still use suitable transmission-line geometry, correct source and load terminations, and a return-path reference to obtain reliable operation.
Typical applications include LVDS backplane buffering, point-to-point high-speed links, industrial data acquisition, communications racks, and instrumentation platforms. The 800-Mbps capability makes the device appropriate for systems that need one LVDS signal to be redistributed or isolated without changing the underlying differential signaling format. The output-enable function is especially useful where multiple buffers share a bus or where the receiver must be disconnected during a controlled system state.
When laying out a circuit using the DS90LV001TMX, place the device close to the source or receiver whose loading is being isolated. Route the differential pair as a controlled-impedance transmission line, keep the pair geometry consistent, and terminate the line according to the system architecture. Check the datasheet's absolute maximum ratings, supply recommendations, and propagation-delay information before finalizing a high-speed design.
This page combines the manufacturer identification, package information, lifecycle status, verified distributor references, practical interface-design guidance, and a conservative comparison of available replacement information. It is intended to help engineers evaluate whether the DS90LV001TMX remains appropriate for an existing LVDS design or whether an alternate sourcing strategy is required.
直接替换替代料: DS90LV001TMX ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: DS90LV001TMX (相同外形与封装尺寸) ——差异在于 Package, Operating Temperature Range.
DS90LV001TMX/NOPB
✅ 直接替换联系询价
查看数据手册 →DS90LV001TM
✅ 直接替换联系询价
查看数据手册 →DS90LV001TMX 规格参数
| Device Type | LVDS-to-LVDS buffer |
| 数据速率 | 800 Mbps |
| Channel Count | 1 channel |
| Input Signal | LVDS |
| Output Signal | LVDS |
| Output Enable | Available; supports TRI-STATE output |
| 封装 | 8-SOIC |
| 工作温度 | -40°C to +85°C |
| Logic Family | LVDS |
| Application | Backplane and high-speed data distribution |
| Signal Integrity Role | Signal buffering and receiver isolation |
| 安装类型 | Surface mount |
| Manufacturer | Texas Instruments |
| 生命周期状态 | Obsolete and no longer manufactured |
DS90LV001TMX 8-soic 引脚配置指南
DS90LV001TMX(8-soic 封装)的引脚配置。 引脚编号、功能和连接图在制造商数据手册中定义。请参阅该手册以了解确切的封装尺寸和焊接指南。
暂无详细引脚数据: DS90LV001TMX.
请参阅 数据手册 以查看完整引脚配置。
典型应用
DS90LV001TMX 适用于 6 应用s: High-Speed Backplane Buffering, Point-to-Point LVDS Link Isolation, Industrial Data Acquisition, Communications Rack Interconnect, Test and Measurement Front Ends, Synchronized Video and Imaging Systems.
High-Speed Backplane Buffering
The DS90LV001TMX fits at a card boundary or receiver input in an 800-Mbps LVDS backplane, where a controlled buffer can isolate the upstream transmitter from downstream board capacitance. Its LVDS-to-LVDS signal path preserves the differential signaling format while the 8-SOIC package supports conventional surface-mount assembly. The design must still use controlled-impedance routing, suitable terminations, and a continuous reference plane to preserve signal integrity.
推荐
Point-to-Point LVDS Link Isolation
Use the DS90LV001TMX when a point-to-point 800-Mbps LVDS link needs source or receiver isolation. The buffer can reduce the loading seen by the original transmitter when placed near the receiving endpoint, helping separate the signal source from cable, connector, and board capacitance. Its output-enable function also permits the output to enter TRI-STATE during controlled bus states, although timing and state sequencing should follow the manufacturer guidance.
推荐
Industrial Data Acquisition
The DS90LV001TMX is suitable for industrial data-acquisition equipment that distributes differential clock or data signals at up to 800 Mbps. Its -40°C to +85°C operating range supports industrial-temperature environments, while the LVDS interface provides a practical basis for reliable transfer across cables or inter-card links. Engineers should verify grounding, connector return paths, and termination values for the complete acquisition channel.
推荐
Communications Rack Interconnect
In a communications rack, the DS90LV001TMX can buffer an 800-Mbps LVDS signal between line cards where stub length or loading would otherwise degrade margin. Placing it close to the receiving card helps control the electrical environment seen by that card. The single-channel SOIC-8 implementation is particularly useful when only one differential route requires buffering and additional fan-out is not needed.
推荐
Test and Measurement Front Ends
The DS90LV001TMX can serve as a signal-conditioning element in test and measurement front ends that distribute high-speed differential clock or data signals. Buffering near the instrument input can reduce sensitivity to source loading and provide controlled high-impedance output states. For accurate measurements, keep the differential pair geometry consistent, minimize discontinuities, and confirm that probe, connector, and termination effects do not dominate the channel behavior.
推荐
Synchronized Video and Imaging Systems
The 800-Mbps DS90LV001TMX can buffer differential synchronization or data links in imaging systems where multiple circuit blocks require consistent signal arrival. Its output-enable pin supports controlled isolation during operating states, while the LVDS electrical interface suits compact, high-speed boards. Layout should preserve differential symmetry and maintain adequate return-path continuity across board and connector transitions.
推荐
推荐产品汇总
工程参考数据: DS90LV001TMX ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | DS90LV001TMX/NOPB | DS90LV001TM |
|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 8-SOIC | 8-SOIC - same package | 8-SOIC - same package |
| Function | Single-channel LVDS-to-LVDS buffer | Single-channel LVDS-to-LVDS buffer | DS90LV001 LVDS buffer |
| Data Rate | 800 Mbps | 800 Mbps | 800 Mbps |
| Output Enable | Yes; TRI-STATE supported | Yes; functional and terminal characteristics are consistent | Yes; same DS90LV001 family |
关键差异点
- Documented drop-in ordering option (对比 DS90LV001TMX/NOPB)
- Same 800-Mbps LVDS buffer function (对比 DS90LV001TM)
- Output control for isolated bus states (对比 DS90LV001TMX/NOPB)
设计说明
Place the DS90LV001TMX close to the endpoint that requires isolation, especially on a card with connector, trace, or receiver capacitance. Route the differential pair with continuous reference-plane return and matched spacing. The buffer can isolate loading, but it cannot correct mismatched impedance, discontinuity, or improper terminations in the complete channel.
Use the manufacturer pin-description table to assign the 8-SOIC connections and preserve the differential geometry from the input through the device to the output. Keep supply and ground connections short, provide a solid ground reference, and avoid routing the LVDS pair beneath switching or other high-current paths. Validate the final stack-up with controlled-impedance calculations.
Do not assume that a family-member suffix is automatically interchangeable in every purchasing environment. Compare the exact orderable drawing, pin names, electrical limits, temperature grade, lead finish, and traceability requirements with the Texas Instruments datasheet. The verified comparison supports DS90LV001TMX/NOPB as package and terminal compatible, but production approval should still be based on the exact suffix documentation.
Use a clean, low-impedance supply and ground arrangement around the 8-SOIC device. Place local high-frequency bypassing at the supply pins according to the manufacturer layout recommendations and keep return-current paths continuous. Confirm the actual supply voltage, current, and bypass values in the manufacturer datasheet before release because those numerical requirements are not stated in the product-page references.
合规信息
The verified references discuss the obsolete lifecycle state and device function but do not explicitly establish the requested compliance categories. The NOPB suffix commonly denotes a lead-free ordering option, but that is not treated as explicit lead-free evidence without the relevant manufacturer declaration.