DS90LV001TMX - 800 Mbps LVDS Buffer | Texas Instruments
MPN: DS90LV001TMX ✗ 停產DS90LV001TMX 概覽
An LVDS buffer is a digital interface component in the LVDS interface IC family. LVDS, or Low-Voltage Differential Signaling, uses low-amplitude differential voltage to transmit high-speed data with common-mode noise rejection and reduced electromagnetic emissions. A buffer placed in the signal path can extend usable distribution distance, isolate a transmitter from capacitive loading, and reduce the effect of imperfect terminations. The DS90LV001 family is therefore positioned between an LVDS transmitter and downstream LVDS receivers within the broader interface IC and semiconductor hierarchy.
The principal electrical characteristic is an 800-Mbps data rate, suitable for high-speed backplane links, industrial control systems, communications equipment, and test platforms. The verified distributor description identifies the DS90LV001TMX as a single-channel LVDS buffer in an 8-SOIC package with an industrial temperature range from -40°C to +85°C. The output-enable pin allows the output to be disabled for bus sharing, controlled test modes, power-management schemes, or designs that need a high-impedance state during transitions.
The device is designed to address signal-conditioning problems caused by transmission-line reflections, loading, and stub length. In large systems, the distance between a transmission line and an unterminated receiver on an individual card can limit system speed. A dedicated LVDS buffer can be placed near the receiver or at a card boundary to create a controlled signal path. Designers must still use suitable transmission-line geometry, correct source and load terminations, and a return-path reference to obtain reliable operation.
Typical applications include LVDS backplane buffering, point-to-point high-speed links, industrial data acquisition, communications racks, and instrumentation platforms. The 800-Mbps capability makes the device appropriate for systems that need one LVDS signal to be redistributed or isolated without changing the underlying differential signaling format. The output-enable function is especially useful where multiple buffers share a bus or where the receiver must be disconnected during a controlled system state.
When laying out a circuit using the DS90LV001TMX, place the device close to the source or receiver whose loading is being isolated. Route the differential pair as a controlled-impedance transmission line, keep the pair geometry consistent, and terminate the line according to the system architecture. Check the datasheet's absolute maximum ratings, supply recommendations, and propagation-delay information before finalizing a high-speed design.
This page combines the manufacturer identification, package information, lifecycle status, verified distributor references, practical interface-design guidance, and a conservative comparison of available replacement information. It is intended to help engineers evaluate whether the DS90LV001TMX remains appropriate for an existing LVDS design or whether an alternate sourcing strategy is required.
直接替換替代品,適用於 DS90LV001TMX — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: DS90LV001TMX (相同外形與佔位) — 差異在於 Package, Operating Temperature Range.
DS90LV001TMX/NOPB
✅ 直接替換聯絡詢價
查看資料表 →DS90LV001TM
✅ 直接替換聯絡詢價
查看資料表 →DS90LV001TMX 規格
| Device Type | LVDS-to-LVDS buffer |
| 資料速率 | 800 Mbps |
| Channel Count | 1 channel |
| Input Signal | LVDS |
| Output Signal | LVDS |
| Output Enable | Available; supports TRI-STATE output |
| 封裝 | 8-SOIC |
| 工作溫度 | -40°C to +85°C |
| Logic Family | LVDS |
| Application | Backplane and high-speed data distribution |
| Signal Integrity Role | Signal buffering and receiver isolation |
| 安裝類型 | Surface mount |
| Manufacturer | Texas Instruments |
| 生命週期狀態 | Obsolete and no longer manufactured |
DS90LV001TMX 8-soic 腳位配置指南
DS90LV001TMX(8-soic 封裝)的腳位配置。 腳位編號、功能與連接圖定義於製造商資料手冊中。請參閱該手冊以取得確切的封裝尺寸與焊接指引。
無詳細腳位定義資料: DS90LV001TMX.
請參閱 資料表 以查看完整腳位配置。
典型應用
DS90LV001TMX 適用於 6 應用s: High-Speed Backplane Buffering, Point-to-Point LVDS Link Isolation, Industrial Data Acquisition, Communications Rack Interconnect, Test and Measurement Front Ends, Synchronized Video and Imaging Systems.
High-Speed Backplane Buffering
The DS90LV001TMX fits at a card boundary or receiver input in an 800-Mbps LVDS backplane, where a controlled buffer can isolate the upstream transmitter from downstream board capacitance. Its LVDS-to-LVDS signal path preserves the differential signaling format while the 8-SOIC package supports conventional surface-mount assembly. The design must still use controlled-impedance routing, suitable terminations, and a continuous reference plane to preserve signal integrity.
推薦
Point-to-Point LVDS Link Isolation
Use the DS90LV001TMX when a point-to-point 800-Mbps LVDS link needs source or receiver isolation. The buffer can reduce the loading seen by the original transmitter when placed near the receiving endpoint, helping separate the signal source from cable, connector, and board capacitance. Its output-enable function also permits the output to enter TRI-STATE during controlled bus states, although timing and state sequencing should follow the manufacturer guidance.
推薦
Industrial Data Acquisition
The DS90LV001TMX is suitable for industrial data-acquisition equipment that distributes differential clock or data signals at up to 800 Mbps. Its -40°C to +85°C operating range supports industrial-temperature environments, while the LVDS interface provides a practical basis for reliable transfer across cables or inter-card links. Engineers should verify grounding, connector return paths, and termination values for the complete acquisition channel.
推薦
Communications Rack Interconnect
In a communications rack, the DS90LV001TMX can buffer an 800-Mbps LVDS signal between line cards where stub length or loading would otherwise degrade margin. Placing it close to the receiving card helps control the electrical environment seen by that card. The single-channel SOIC-8 implementation is particularly useful when only one differential route requires buffering and additional fan-out is not needed.
推薦
Test and Measurement Front Ends
The DS90LV001TMX can serve as a signal-conditioning element in test and measurement front ends that distribute high-speed differential clock or data signals. Buffering near the instrument input can reduce sensitivity to source loading and provide controlled high-impedance output states. For accurate measurements, keep the differential pair geometry consistent, minimize discontinuities, and confirm that probe, connector, and termination effects do not dominate the channel behavior.
推薦
Synchronized Video and Imaging Systems
The 800-Mbps DS90LV001TMX can buffer differential synchronization or data links in imaging systems where multiple circuit blocks require consistent signal arrival. Its output-enable pin supports controlled isolation during operating states, while the LVDS electrical interface suits compact, high-speed boards. Layout should preserve differential symmetry and maintain adequate return-path continuity across board and connector transitions.
推薦
推薦產品摘要
工程參考資料,適用於 DS90LV001TMX — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | DS90LV001TMX/NOPB | DS90LV001TM |
|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 8-SOIC | 8-SOIC - same package | 8-SOIC - same package |
| Function | Single-channel LVDS-to-LVDS buffer | Single-channel LVDS-to-LVDS buffer | DS90LV001 LVDS buffer |
| Data Rate | 800 Mbps | 800 Mbps | 800 Mbps |
| Output Enable | Yes; TRI-STATE supported | Yes; functional and terminal characteristics are consistent | Yes; same DS90LV001 family |
主要差異化特點
- Documented drop-in ordering option (對比DS90LV001TMX/NOPB)
- Same 800-Mbps LVDS buffer function (對比DS90LV001TM)
- Output control for isolated bus states (對比DS90LV001TMX/NOPB)
設計說明
Place the DS90LV001TMX close to the endpoint that requires isolation, especially on a card with connector, trace, or receiver capacitance. Route the differential pair with continuous reference-plane return and matched spacing. The buffer can isolate loading, but it cannot correct mismatched impedance, discontinuity, or improper terminations in the complete channel.
Use the manufacturer pin-description table to assign the 8-SOIC connections and preserve the differential geometry from the input through the device to the output. Keep supply and ground connections short, provide a solid ground reference, and avoid routing the LVDS pair beneath switching or other high-current paths. Validate the final stack-up with controlled-impedance calculations.
Do not assume that a family-member suffix is automatically interchangeable in every purchasing environment. Compare the exact orderable drawing, pin names, electrical limits, temperature grade, lead finish, and traceability requirements with the Texas Instruments datasheet. The verified comparison supports DS90LV001TMX/NOPB as package and terminal compatible, but production approval should still be based on the exact suffix documentation.
Use a clean, low-impedance supply and ground arrangement around the 8-SOIC device. Place local high-frequency bypassing at the supply pins according to the manufacturer layout recommendations and keep return-current paths continuous. Confirm the actual supply voltage, current, and bypass values in the manufacturer datasheet before release because those numerical requirements are not stated in the product-page references.
合規資訊
The verified references discuss the obsolete lifecycle state and device function but do not explicitly establish the requested compliance categories. The NOPB suffix commonly denotes a lead-free ordering option, but that is not treated as explicit lead-free evidence without the relevant manufacturer declaration.