Microchip Technology

KSZ9031MNXCA - Automotive Gigabit Ethernet PHY | Microchip

料号: KSZ9031MNXCA ✓ 量产中
3.3 V, 2.5 V, and 1.8 V Vdss 48-QFN, 7x7 mm Package 10Base-T, 100Base-TX, and 1000Base-T Speed
最小起订量: 1 |

KSZ9031MNXCA 概述

The Microchip Technology KSZ9031MNXCA is an automotive-qualified, fully integrated triple-speed Ethernet physical layer transceiver supporting 10Base-T, 100Base-TX, and 1000Base-T operation in a 48-QFN 7x7 mm package. The device provides one Ethernet PHY port with GMII and MII support, integrated cable diagnostics through LinkMD, and configurable 3.3 V, 2.5 V, and 1.8 V supply operation.

An Ethernet PHY, also called a physical-layer transceiver, is the semiconductor interface between a digital Ethernet controller and physical copper wiring. It serializes and deserializes MAC-layer data, encodes it onto copper cables, recovers timing, detects link state, and negotiates the highest common speed. Within the network hierarchy, the KSZ9031 belongs to the Ethernet interface IC and physical-layer transceiver class, where it bridges a host controller such as a microcontroller, application processor, or communications processor and a 10/100/1000Base-T network.

The KSZ9031 supports all three common twisted-pair Ethernet rates, including 1000Base-T over standard category 5 unshielded twisted pair. Its auto-negotiation implementation follows Clause 28 of the IEEE 802.3 specification, allowing a link partner to select the highest mutually supported operating mode. LinkMD diagnostics add cable-length and fault-location capabilities that help industrial and automotive system integrators identify installation problems. Configurable 1.8 V, 2.5 V, and 3.3 V rails support integration with both legacy and current digital systems.

The GMII and MII interfaces provide configurable digital connectivity between the PHY and the upper-layer Ethernet controller. This flexibility allows the same physical-layer device to be used in architectures operating at different MAC-clock rates and with different parallel-data requirements. The device family is designed for automotive-qualified applications, where consistent operation, diagnostic visibility, and supply-voltage flexibility are important for long-lived embedded networks.

Typical uses include industrial Ethernet controllers, automotive head-unit or vehicle-networking platforms, communications equipment, embedded network processors, and factory automation systems. The integrated 1000Base-T capability reduces the need for separate physical-layer transceivers when a system must support 10, 100, and 1000 Mb/s links through one network port. LinkMD diagnostics are particularly useful in installations where cable routing, connector integrity, or field-service troubleshooting can be difficult.

PCB implementation should follow the manufacturer datasheet for the 48-QFN land pattern, exposed-pad connection, decoupling, and high-speed differential-routing requirements. Keep the magnetic-component interface and Ethernet traces short, preserve the specified impedance-controlled geometry, and provide the specified power and ground decoupling near the PHY. Do not substitute connector or magnetics arrangements without reviewing the reference circuit because center-tap, bias, and termination requirements vary with the network design.

This product page combines the manufacturer’s KSZ9031 family information with practical selection guidance, verified package details, interface guidance, and same-footprint ordering-code alternatives. It is intended to help engineers identify the correct automotive Ethernet PHY variant while preserving board compatibility and understanding the distinctions that require qualification review.

直接替换替代料: KSZ9031MNXCA ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。

本系列中的变体

可与以下型号直接替换的同系列型号: KSZ9031MNXCA (相同外形与封装尺寸) ——差异在于 Package, Product Type, Data Rate, Auto-Negotiation, Cable Type.

Microchip Technology
Package: 64-pin QFN (8x8 mm), lead-free
Product Type: Ethernet PHY Transceiver
Data Rate: 10/100/1000 Mbps
对比 KSZ9031MNXCA →
Microchip Technology
Package: 64-pin QFN, 8 mm x 8 mm
Product Type: Integrated Ethernet physical layer transceiver
对比 KSZ9031MNXCA →
Microchip Technology
Package: 64-pin QFN
Product Type: Triple-speed Ethernet physical-layer transceiver
Cable Type: CAT-5 unshielded twisted-pair cable
对比 KSZ9031MNXCA →
Microchip Technology
Package: 48-pin QFN, 7 mm x 7 mm
Product Type: Gigabit Ethernet physical-layer transceiver
对比 KSZ9031MNXCA →
Microchip Technology
Package: 48-pin QFN (7x7 mm)
Product Type: Ethernet Physical Layer Transceiver (PHY)
Data Rate: 10 / 100 / 1000 Mbps (triple-speed)
对比 KSZ9031MNXCA →
Microchip Technology
Package: 48-QFN (7x7 mm)
Product Type: Ethernet Transceiver (PHY)
Data Rate: 10/100/1000 Mbps
对比 KSZ9031MNXCA →
Microchip Technology
Package: 48-pin QFN (7x7 mm) with Exposed Pad
Product Type: Ethernet Physical Layer Transceiver (PHY)
Data Rate: 10/100/1000 Mbps (Triple-Speed)
对比 KSZ9031MNXCA →

KSZ9031MNXIA

✅ 直接替换
Microchip Technology
📦 48-QFN (7x7 mm)
Integrated Ethernet physical layer transceiver · 10 Mb/s, 100 Mb/s, and 1000 Mb/s · 1 channel · 10BASE-T, 100BASE-TX, and 1000BASE-T · CAT-5 unshielded twisted-pair cable · LinkMD · Automotive qualified · 64-pin QFN, 8 mm x 8 mm

联系询价

查看数据手册 →

KSZ9031MNXIC

✅ 直接替换
Microchip Technology
📦 48-QFN (7x7 mm)
10 Mb/s, 100 Mb/s, and 1000 Mb/s · 10Base-T, 100Base-TX, and 1000Base-T · CAT-5 unshielded twisted-pair cable · Triple-speed Ethernet physical-layer transceiver · GMII/MII · Automotive qualified · LinkMD · Supported

联系询价

查看数据手册 →

KSZ9031MNXCC

✅ 直接替换
Microchip Technology
📦 48-QFN (7x7 mm)
Ethernet PHY Transceiver · 10/100/1000 Mbps · IEEE 802.3 (10Base-T/100Base-TX/1000Base-T) · GMII / MII · 3.3V / 2.5V / 1.8V · 3.3V (single supply) · ~0.7W at 1000 Mbps full-duplex · Yes (10/100/1000 Mbps)

联系询价

查看数据手册 →

KSZ9031RNXCA

✅ 直接替换
Microchip Technology
📦 48-QFN (7x7 mm)
Gigabit Ethernet physical-layer transceiver · 10 Mbps, 100 Mbps, and 1 Gbps · 10Base-T, 100Base-TX, and 1000Base-T · RGMII · 4-wire full-duplex Ethernet · 1.8 V, 2.5 V, and 3.3 V · 1.2 V · 48-pin QFN, 7 mm x 7 mm

联系询价

查看数据手册 →

KSZ9031RNXIA

✅ 直接替换
Microchip Technology
📦 48-QFN (7x7 mm)
Ethernet Transceiver (PHY) · 10/100/1000 Mbps · 10Base-T, 100Base-TX, 1000Base-T · RGMII · 1 Port · 1.8V / 2.5V / 3.3V · 3.3V · CAT-5 UTP

联系询价

查看数据手册 →

KSZ9031RNXIC

✅ 直接替换
Microchip Technology
📦 48-QFN (7x7 mm)
Ethernet Physical Layer Transceiver (PHY) · 10/100/1000 Mbps (Triple-Speed) · IEEE 802.3 10BASE-T / 100BASE-TX / 1000BASE-T · RGMII (version 2.0, on-chip delay) · 4/4 Transceiver (Full Duplex) · 1.8 V / 2.5 V / 3.3 V · 48-pin QFN (7x7 mm) with Exposed Pad · CAT-5 Unshielded Twisted Pair (UTP)

联系询价

查看数据手册 →

KSZ9031RNXCC

✅ 直接替换
Microchip Technology
📦 48-QFN (7x7 mm)
Ethernet Physical Layer Transceiver (PHY) · 10 / 100 / 1000 Mbps (triple-speed) · IEEE 802.3, 802.3u, 802.3ab, 802.3az (EEE) · RGMII (Version 2.0 compliant, on-chip delay) · 4 differential pairs, CAT-5 UTP, 100-ohm differential · MDIO / MDC (IEEE 802.3 clause 22/45) · 3.3 V · 1.2 V (on-chip LDO controller + external MOSFET)

联系询价

查看数据手册 →

KSZ9031MNXCA 规格参数

Product Type Automotive Ethernet physical-layer transceiver
Ethernet Port Count 1 port
Supported Ethernet Speeds 10Base-T, 100Base-TX, and 1000Base-T
Maximum Nominal Ethernet Rate 1000 Mb/s
Medium Support Standard CAT-5 unshielded twisted pair
Host Interface GMII and MII
Cable Diagnostics LinkMD
Automotive Qualification Automotive qualified
Supply Voltage Options 3.3 V, 2.5 V, and 1.8 V
封装 48-QFN, 7x7 mm
安装类型 Surface mount
Auto-Negotiation IEEE 802.3 Clause 28

KSZ9031MNXCA 48-qfn, 7x7 mm 引脚配置指南

KSZ9031MNXCA(48-qfn, 7x7 mm 封装)的引脚配置。 引脚编号、功能和连接图在制造商数据手册中定义。请参阅该手册以了解确切的封装尺寸和焊接指南。

KSZ9031MNXCA 的 48-qfn, 7x7 mm 封装引脚图

暂无详细引脚数据: KSZ9031MNXCA.

请参阅 数据手册 以查看完整引脚配置。

典型应用

KSZ9031MNXCA 适用于 6 应用s: Automotive Ethernet Networking, Industrial Factory Automation, Communications Equipment, Embedded Network Processor Platform, Network Equipment Cable Diagnostics, Industrial Control and Monitoring.

🚗

Automotive Ethernet Networking

The KSZ9031MNXCA fits an automotive Ethernet node that requires one physical port supporting 10Base-T, 100Base-TX, and 1000Base-T. Its automotive-qualified family status, LinkMD diagnostics, and configurable 1.8 V, 2.5 V, or 3.3 V supplies support integration with automotive-domain controllers. The PHY connects a digital host controller to the appropriate Ethernet magnetics and cable. LinkMD can help commissioning and service teams identify wiring faults. Qualification details, temperature limits, and network topology must still be confirmed for the selected ordering code.

🏭

Industrial Factory Automation

The KSZ9031MNXCA is suitable for a factory controller or programmable-logic node that must connect industrial equipment over copper Ethernet. One port can negotiate 10 Mb/s, 100 Mb/s, or 1000 Mb/s, while GMII and MII support broad compatibility with embedded controllers. LinkMD diagnostics improve fault isolation in long installations where cable damage or connector errors are common. The 48-QFN 7x7 mm package supports compact controller boards, although the magnetics, surge protection, and controlled-impedance layout remain essential for industrial EMC performance.

🌐

Communications Equipment

The KSZ9031MNXCA can provide the physical layer for communications equipment requiring a compact Gigabit Ethernet uplink. Its one-port 10/100/1000Base-T support allows common management, backplane, or service interfaces to share the PHY, while GMII and MII permit adaptation to different host-controller clocking architectures. LinkMD assists remote installation and maintenance. Designers should use the manufacturer’s recommended magnetics and reference layout because the performance of 1000Base-T depends on controlled PCB geometry, proper power decoupling, and a correctly implemented transformer interface.

🖥️

Embedded Network Processor Platform

The KSZ9031MNXCA is appropriate for an embedded network processor, secure gateway, or service node requiring a single copper Ethernet port. A one-port PHY with three supported rates allows the platform to interoperate with legacy 10/100 Mb/s equipment while retaining a 1000 Mb/s option for throughput-oriented links. The selectable 1.8 V, 2.5 V, and 3.3 V supply configurations can simplify integration across the host’s power tree. Interface timing, reset behavior, register defaults, and clock requirements must be reviewed against the selected host controller.

🔧

Network Equipment Cable Diagnostics

The KSZ9031MNXCA fits diagnostic-heavy network equipment where installation faults must be identified quickly. LinkMD cable diagnostics complement the PHY’s 10Base-T, 100Base-TX, and 1000Base-T operation by providing visibility into the copper link. In a managed switch, gateway, or test appliance, this diagnostic information can be exposed through the management interface to shorten service time. The implementation should follow the KSZ9031 family diagnostics procedure and account for magnetics, termination, and cable characteristics when interpreting the results.

🧩

Industrial Control and Monitoring

The KSZ9031MNXCA can serve as the Ethernet interface in a PLC, data logger, sensor gateway, or remote monitoring unit. Its three-speed support improves interoperability with older 10/100 Mb/s infrastructure, while the 1000Base-T capability provides a path to faster data collection. GMII and MII interfaces allow selection according to the controller’s data rate and timing architecture. Diagnostic cable-status information can help operators distinguish physical-layer faults from higher-level network problems, and the compact 48-QFN package supports dense control hardware.

What is the KSZ9031MNXCA?
The KSZ9031MNXCA is a Microchip Technology automotive-qualified Gigabit Ethernet PHY that combines 10Base-T, 100Base-TX, and 1000Base-T support with GMII and MII host interfaces. According to the manufacturer product page, it is a fully integrated triple-speed Ethernet physical-layer transceiver with LinkMD cable diagnostics, and it uses a 48-QFN 7x7 mm package for surface-mounted automotive and industrial network designs.
What Ethernet speeds does the KSZ9031MNXCA support?
The KSZ9031MNXCA supports 10Base-T, 100Base-TX, and 1000Base-T operation, with a maximum nominal link rate of 1000 Mb/s. The manufacturer describes it as a triple-speed PHY for standard CAT-5 unshielded twisted-pair cabling, allowing one physical network port to accommodate 10 Mb/s, 100 Mb/s, and 1 Gb/s links after negotiation.
Where can I download the KSZ9031MNXCA datasheet PDF?
The official KSZ9031MNX datasheet PDF is available from Microchip Technology at https://www.microchip.com/content/dam/mchp/documents/OTH/ProductDocuments/DataSheets/00002096E.pdf. It covers the KSZ9031MNX family, including triple-speed Ethernet operation, GMII and MII interfaces, power configurations, LinkMD diagnostics, and the recommended application circuit. Use the pin-description and layout sections when assigning connections and designing the PCB.
Where can I find the KSZ9031MNXCA pinout?
The KSZ9031MNXCA pin assignments are documented in the pin-description table of the official Microchip Technology KSZ9031MNX datasheet. Use that table to map the 48-QFN connections, exposed pad, power rails, grounds, reset, clocks, and management signals. The complete package drawing and land pattern should also be taken from the manufacturer’s package information rather than inferred from a distributor category page.
Is the KSZ9031MNXCA suitable for automotive Ethernet?
Yes, the KSZ9031MNXCA belongs to the automotive-qualified KSZ9031 family. The manufacturer identifies the KSZ9031 as an automotive-qualified integrated triple-speed Ethernet PHY with LinkMD cable diagnostics. Before releasing a vehicle or industrial design, confirm the exact ordering code’s temperature range, AEC-Q100 grade, production status, and automotive qualification details in the manufacturer’s product documentation.
What is LinkMD cable diagnostics on the KSZ9031MNXCA?
LinkMD is the cable-diagnostics feature available in the KSZ9031 family. It gives the system a means to identify cable faults and estimate cable characteristics during installation or maintenance. The diagnostic result can reduce field troubleshooting time by distinguishing wiring problems from controller, PHY, or network-configuration faults. Use the manufacturer application information to determine the supported cable lengths and diagnostic operating procedure.
What is the difference between GMII and MII on the KSZ9031MNXCA?
GMII and MII are both parallel digital interfaces between an Ethernet MAC or controller and the physical-layer transceiver, but they support different clock and data arrangements. The KSZ9031MNXCA supports both, allowing it to pair with controllers designed around either interface. Select the operating mode from the host-controller requirements, then use the manufacturer pin and register descriptions for configuration.
What supply voltages can the KSZ9031MNXCA use?
The KSZ9031MNXCA supports 3.3 V, 2.5 V, and 1.8 V supply configurations. These options allow the PHY to be integrated with digital controllers operating at different rail levels and can simplify shared-rail designs in industrial and automotive equipment. The appropriate connection and decoupling arrangement for each configuration must follow the datasheet’s power-supply section and reference schematic.
Can I use the KSZ9031MNXCA with a CAT-5 cable?
The KSZ9031MNXCA is intended for 10Base-T, 100Base-TX, and 1000Base-T links over standard CAT-5 unshielded twisted pair. The Ethernet medium still requires the appropriate network magnetics, connector, protection, and physical-layer implementation described by the manufacturer. Cable category, length, installation practices, and the grounding topology should be checked against the applicable Ethernet system specification.
What can replace the KSZ9031MNXCA on the same PCB?
The KSZ9031MNXIA, KSZ9031MNXIC, KSZ9031MNXCC, and KSZ9031RNX-series ordering codes are the closest same-family candidates identified for the 48-QFN KSZ9031 platform. Each retains the one-port triple-speed Ethernet PHY function and 48-QFN 7x7 mm footprint, while the ordering code indicates a difference in qualification or configuration. Verify pinout, temperature range, interface settings, automotive documentation, and lifecycle status before substitution.
Is the KSZ9031RNXCA a drop-in replacement for the KSZ9031MNXCA?
The KSZ9031RNXCA is a candidate for a no-PCB-change transition because it is listed in the same 48-QFN 7x7 mm KSZ9031 family and retains the one-port Gigabit Ethernet PHY function. It is not automatically electrically identical: ordering-code, qualification, and configuration distinctions must be checked against the two datasheets and product pages. Confirm the pin assignments, register defaults, clocking, power sequencing, and automotive documentation before production use.
When should I choose the KSZ9031MNXCA over another Ethernet PHY?
Choose the KSZ9031MNXCA when the design needs a 48-QFN, one-port PHY that supports 10/100/1000 Mb/s, GMII and MII connectivity, LinkMD diagnostics, and an automotive-qualified family option. A different PHY should be selected only when its package, host interface, diagnostic feature set, qualification, or supply architecture is demonstrably better suited. Compatibility alone is not a substitute for checking the exact controller interface and qualification requirements.
Where can I buy the KSZ9031MNXCA and check current availability?
Use the Request a Quote form on this page to request the KSZ9031MNXCA, current availability, order quantity, and delivery schedule from XAIPART. The part is identified as an active Microchip Technology Ethernet interface IC, but practical stock and lead time can change with package code, production allocation, and order volume. Include the intended shipment date and target quantity in the request.
What is the price of the KSZ9031MNXCA?
The current commercial price of the KSZ9031MNXCA is not stated on this page because pricing is maintained as a live structured listing rather than a static article figure. Use the Request a Quote form on this page for the unit price and volume tiers applicable to the requested quantity. The form can also clarify stock allocation, manufacturer packaging, and expected delivery information.
What are the key specifications engineers should know about the KSZ9031MNXCA?
The key KSZ9031MNXCA specifications are one Ethernet port, simultaneous support for 10Base-T, 100Base-TX, and 1000Base-T, a maximum nominal rate of 1000 Mb/s, GMII and MII host interfaces, and LinkMD cable diagnostics. The device is associated with the automotive-qualified KSZ9031 family, supports 3.3 V, 2.5 V, and 1.8 V supply configurations, and uses a 48-QFN 7x7 mm surface-mount package.

工程参考数据: KSZ9031MNXCA ——对比、设计指导和合规信息。

选型指南

Choose the KSZ9031MNXCA when the system requires a one-port 10/100/1000Base-T copper Ethernet interface, GMII or MII connectivity, LinkMD diagnostics, and a device associated with the automotive-qualified KSZ9031 family. The 48-QFN 7x7 mm package also suits compact controller boards where a transformer and Ethernet protection network are already part of the reference design. The MNXIA, MNXIC, and MNXCC variants are candidates when the PCB and PHY function remain unchanged but the qualification-ordering code must be changed; confirm temperature grade, automotive documentation, and availability. The RNX-series alternatives share the QFN footprint and core Ethernet function, but their ordering-code configuration must be compared before substitution. No cross-brand PHY should be treated as drop-in unless its pinout, interface timing, power architecture, diagnostics, and package have been independently verified. Final selection should be based on the exact host controller, qualification target, cable-magnetics design, and production schedule.

与替代料对比

参数 本产品 KSZ9031MNXIA KSZ9031MNXIC KSZ9031MNXCC KSZ9031RNXCA
Brand Microchip Technology Microchip Technology Microchip Technology Microchip Technology Microchip Technology
Package 48-QFN (7x7 mm) 48-QFN (7x7 mm) 48-QFN (7x7 mm) 48-QFN (7x7 mm) 48-QFN (7x7 mm)
Ethernet Port Count 1 port 1 port 1 port 1 port 1 port
Supported Ethernet Speeds 10Base-T, 100Base-TX, and 1000Base-T 10Base-T, 100Base-TX, and 1000Base-T 10Base-T, 100Base-TX, and 1000Base-T 10Base-T, 100Base-TX, and 1000Base-T 10Base-T, 100Base-TX, and 1000Base-T
Maximum Nominal Ethernet Rate 1000 Mb/s 1000 Mb/s 1000 Mb/s 1000 Mb/s 1000 Mb/s
Host Interface GMII and MII GMII and MII GMII and MII GMII and MII GMII and MII
Cable Diagnostics LinkMD LinkMD LinkMD LinkMD LinkMD
Supply Voltage Options 3.3 V, 2.5 V, and 1.8 V 3.3 V, 2.5 V, and 1.8 V 3.3 V, 2.5 V, and 1.8 V 3.3 V, 2.5 V, and 1.8 V 3.3 V, 2.5 V, and 1.8 V
Ordering-Code Qualification MNXCA automotive ordering code Different qualification-ordering code Different qualification-ordering code Different qualification-ordering code RNX configuration ordering code

关键差异点

  • Combines three copper Ethernet rates in one physical port (对比 KSZ9031RNXCA)
  • Provides LinkMD diagnostics for cable troubleshooting (对比 KSZ9031MNXCC)
  • Supports multiple digital supply configurations (对比 KSZ9031MNXIA)
  • Uses the same 48-QFN 7x7 mm footprint across listed alternatives (对比 KSZ9031RNXIA)

设计说明

Follow the manufacturer’s 48-QFN land pattern and reference layout exactly, including the exposed-pad connection and component placement around the Ethernet transformer. Place the PHY and its decoupling capacitors close to the relevant supply pins, provide a low-impedance ground path, and preserve the recommended differential-pair geometry. The 1000Base-T channel is sensitive to impedance discontinuities and return-path interruptions, so substitutions in the magnetics, protection, or termination networks should be qualified as complete layout changes.

Treat the Ethernet differential pairs as controlled-impedance transmission lines rather than ordinary short traces. Use the manufacturer’s preferred pair spacing, length relationship, connector or magnetics launch geometry, and reference-plane treatment to minimize reflections and impedance discontinuities. Keep the PHY-to-magnetics path as short as practical, avoid right-angle routing, and maintain a continuous ground reference beneath the pairs. These practices are especially important at the 1000 Mb/s operating mode.

Design the 3.3 V, 2.5 V, and 1.8 V supply rails so the PHY receives clean power during link startup, reset, and high-data-rate operation. Use the values and capacitor types specified by the manufacturer, place bias or decoupling networks at their reference positions, and provide adequate source capability for the selected operating mode. Check rail sequencing and power-off behavior against the host controller so the MAC interface never sees an invalid electrical state during initialization.

Do not assume that identical QFN land patterns make two ordering codes functionally interchangeable. Before replacing the KSZ9031MNXCA with an MNX or RNX variant, compare the pin description table, exposed-pad treatment, register defaults, clock requirements, reset behavior, interface timing, qualification grade, and temperature range. In particular, an automotive qualification mark alone does not establish that every ordering code meets a specific vehicle program’s environmental or production requirements.

合规信息

RoHS
Unknown
REACH
Unknown
AEC-Q100
Qualified
无铅
Unknown
无卤
Unknown
冲突矿物
Unknown

Microchip identifies the KSZ9031 family as automotive qualified. The exact ordering-code AEC-Q100 grade, RoHS status, REACH status, lead-free status, halogen-free status, and conflict-minerals declaration should be confirmed in the manufacturer’s product documentation.

相关搜索

KSZ9031MNXCA datasheet KSZ9031MNXCA pinout KSZ9031MNXCA datasheet pdf KSZ9031MNXCA equivalent KSZ9031MNXCA replacement KSZ9031MNXCA cross reference KSZ9031MNXCA 48-QFN KSZ9031MNXCA Gigabit Ethernet PHY KSZ9031MNXCA automotive Ethernet KSZ9031MNXCA price KSZ9031MNXCA stock KSZ9031MNXCA vs KSZ9031RNXCA

相关元器件 & 术语

Microchip Technology KSZ9031MNXCA KSZ9031MNXIA KSZ9031MNXIC KSZ9031MNXCC KSZ9031RNXCA KSZ9031RNXIA KSZ9031RNXIC KSZ9031RNXCC Ethernet PHY physical-layer transceiver Ethernet interface IC 10Base-T 100Base-TX 1000Base-T Gigabit Ethernet GMII MII LinkMD IEEE 802.3 Clause 28 automotive qualified 48-QFN QFN package family surface-mount technology CAT-5 unshielded twisted pair
快速报价
填写完整信息——我们的销售团队将在 24 小时内回复
料号 制造商 封装 QTY 目标价 小计
✓
报价已提交!

我们将在 24 小时内回复您的邮件

1
询价已提交
2
已收到报价
3
已下单
4
支付
5
已发货
6
已送达
查看询价详情