KSZ9031MNXIA - 1GbE Automotive Ethernet PHY | Microchip
料号: KSZ9031MNXIA ✓ 量产中KSZ9031MNXIA 概述
An Ethernet PHY is the physical-layer interface between a digital network controller or processor and twisted-pair cabling. It converts digital data into electrical signaling for transmission and converts received signals back into digital data for the host controller. Within the Ethernet hierarchy, the KSZ9031MNXIA belongs to the Ethernet physical layer transceiver category, operating below the MAC and network-interface layers while supporting standard CAT-5 unshielded twisted-pair cabling.
The device combines 10 Mb/s, 100 Mb/s, and 1000 Mb/s capability in one transceiver. Triple-speed support allows the same physical layer to interoperate with legacy 10 Mb/s equipment, Fast Ethernet networks, and Gigabit Ethernet infrastructure. LinkMD adds cable diagnostics that help system integrators identify opens, shorts, and wiring errors, reducing installation time and field maintenance effort. The manufacturer identifies the KSZ9031 as automotive qualified and highlights LinkMD as a principal product feature.
KSZ9031MNXIA integrates the analog PHY functions needed for bidirectional communication over standard twisted-pair media. Automotive implementations commonly place the PHY close to the connector and route controlled-impedance traces to the Ethernet magnetics, while the digital management interface connects it to an automotive-capable Ethernet controller. Keeping the high-frequency analog section separated from switching and processor circuitry helps reduce susceptibility to common-mode interference and digital crosstalk.
Typical deployments include automotive infotainment and connectivity domains, in-vehicle Ethernet backbones, vehicle-to-vehicle communication gateways, industrial Ethernet equipment, and other embedded network nodes. Gigabit capability is useful where bandwidth requirements exceed Fast Ethernet limits, while backward compatibility allows connection to lower-speed infrastructure during fleet transitions. Automotive qualification should be confirmed against the exact ordering code and system-level requirements before release.
PCB implementation requires careful separation between the Ethernet magnetics, differential pairs, clock circuitry, supply decoupling, and digital control signals. Follow the manufacturer datasheet for the exact 64-QFN pad layout, exposed-pad connection, component values, isolation spacing, and reference circuit. In particular, do not infer pin functions from the package drawing alone; use the datasheet pin-description table when assigning tracks or reviewing a PCB revision.
This page organizes the manufacturer product information, package characteristics, sourcing guidance, application considerations, and verified drop-in comparison options into one engineering-focused reference. It also highlights the differences between bond-wire ordering variants so engineers can distinguish mechanical interchangeability from material and qualification decisions.
直接替换替代料: KSZ9031MNXIA ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: KSZ9031MNXIA (相同外形与封装尺寸) ——差异在于 Package, Product Type.
KSZ9031MNXIC
✅ 直接替换联系询价
查看数据手册 →KSZ9031MNXIA 规格参数
| Product Type | Integrated Ethernet physical layer transceiver |
| Ethernet Speed Support | 10 Mb/s, 100 Mb/s, and 1000 Mb/s |
| Number of PHY Channels | 1 channel |
| Supported Standards | 10BASE-T, 100BASE-TX, and 1000BASE-T |
| Medium | CAT-5 unshielded twisted-pair cable |
| Cable Diagnostics | LinkMD |
| Automotive Qualification | Automotive qualified |
| 封装 | 64-pin QFN, 8 mm x 8 mm |
| 安装类型 | Surface mount |
| 引脚数 | 64 pins |
| Maximum Data Rate | 1 Gb/s |
| Media Interface | Integrated differential Ethernet PHY |
KSZ9031MNXIA 64-pin qfn, 8 mm x 8 mm 引脚配置指南
KSZ9031MNXIA(64-pin qfn, 8 mm x 8 mm 封装)的引脚配置。 引脚编号、功能和连接图在制造商数据手册中定义。请参阅该手册以了解确切的封装尺寸和焊接指南。
暂无详细引脚数据: KSZ9031MNXIA.
请参阅 数据手册 以查看完整引脚配置。
典型应用
KSZ9031MNXIA 适用于 3 应用s: 嵌入式系统, 物联网设备, 工业控制.
嵌入式系统
使用 KSZ9031MNXIA 在嵌入式应用中进行核心处理。
物联网设备
由 KSZ9031MNXIA 驱动的智能联网设备。
工业控制
使用 KSZ9031MNXIA 的自动化和控制系统。
工程参考数据: KSZ9031MNXIA ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | KSZ9031MNXIC |
|---|---|---|
| Brand | Microchip Technology | Microchip Technology |
| Package | 64-QFN (8 mm x 8 mm) | 64-QFN (8 mm x 8 mm) |
| Ethernet Speeds | 10BASE-T, 100BASE-TX, 1000BASE-T | 10BASE-T, 100BASE-TX, 1000BASE-T |
| Maximum Data Rate | 1 Gb/s | 1 Gb/s |
| PHY Channels | 1 channel | 1 channel |
| Cable Diagnostics | LinkMD | LinkMD |
| Cable Medium | CAT-5 unshielded twisted-pair cable | CAT-5 unshielded twisted-pair cable |
| Bonding Wire | Gold | Copper |
| Automotive Qualification | Qualified | Same functional ordering family; verify exact qualification record |
关键差异点
- Gold bonding-wire construction in the primary ordering code (对比 KSZ9031MNXIC)
- Integrated diagnostic support (对比 KSZ9031MNXIC)
- Single-package automotive Ethernet connectivity (对比 KSZ9031MNXIC)
设计说明
Place the PHY and its supporting clock and decoupling network in the same uninterrupted Ethernet analog section of the PCB. Follow the manufacturer reference layout for every decoupling capacitor, including the placement and connection of the 64-QFN exposed pad. Keep the Ethernet differential pairs short, continuous, and symmetrical, with their return path over a continuous reference plane. Avoid routing digital, switching, and high-current supply paths beneath the PHY or magnetics area.
Use the manufacturer-recommended differential impedance and pair-length geometry for both copper and fiber media interfaces connected to the Ethernet magnetics. Keep the 100BASE-TX and 1000BASE-T paths away from switching-node edges and high-current inductors. Maintain the specified isolation around the magnetics and line-driver circuitry because automotive environments combine high-energy transient events with long cable runs. Validate the complete channel with eye diagrams and compliance testing before production release.
Do not treat KSZ9031MNXIA and KSZ9031MNXIC as automatically approved for every vehicle program solely because their documented difference is bonding-wire material. Review the exact ordering information, AEC-Q100 status, temperature grade, traceability requirements, and customer-specific qualification rules. Microchip reports equal long-term reliability and burn-in testing for the copper-wire construction, but procurement approval and change-control documentation remain necessary for an automotive substitution.
Use the exposed pad as the primary thermal path and follow the manufacturer’s thermal-layout and paste-application guidance. Estimate junction temperature from actual switching loss, ambient conditions, board copper area, and the thermal resistance associated with the selected PCB construction. Avoid relying on package body size alone because the 8 mm by 8 mm QFN transfers most heat through its exposed pad and internal vias.
合规信息
Microchip identifies the KSZ9031 as automotive qualified. Exact RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations for the KSZ9031MNXIA ordering code should be confirmed in the current manufacturer product documentation.