Texas Instruments

MAX3243EIDWRG4 - 3/5 RS-232 Transceiver, 250kbps, 5.5V | Texas Instruments

料号: MAX3243EIDWRG4 ✓ 量产中
3 V to 5.5 V Vdss 28-pin SOIC (DW), gull wing, surface mount Package
最小起订量: 1 |

MAX3243EIDWRG4 概述

The Texas Instruments MAX3243EIDWRG4 is a 3-to-5.5 V multichannel RS-232 line driver and receiver with 250 kbps signalling rate and plus or minus 15 kV ESD (HBM) protection, housed in a 28-pin SOIC (DW) package. It integrates three RS-232 drivers and five RS-232 receivers in a single package, making it the workhorse multi-channel transceiver for industrial serial connectivity.

An RS-232 transceiver is a type of interface IC that converts logic-level TTL/CMOS signals into RS-232 differential voltage levels and back again. It belongs to the line driver and receiver family, which sits inside interface ICs, which in turn are part of the wider communication and power management semiconductor hierarchy. Because RS-232 uses single-ended bipolar signalling referenced to ground, a transceiver also handles level translation, slew control and, in this case, electrostatic discharge hardening for connector-facing pins.

Key features of this device include a 3 V to 5.5 V supply range, a 250 kbps maximum data rate, three transmit channels, five receive channels, on-chip charge pump doubling circuitry with external capacitor pins, and plus or minus 15 kV human-body-model ESD protection. The industrial-temperature grade and gull-wing surface-mount SOIC-28 form factor support long-life industrial and instrumentation equipment.

Internally, the driver channels use slew-rate-limited push-pull outputs to limit ringing on long cables, while the receiver channels add hysteresis for noise immunity. The charge-pump and voltage-doubler generate the plus and minus rail voltages required by the RS-232 drivers from a single supply, so no external negative supply is needed. The result is a compact single-chip solution where previously several discrete driver and receiver ICs were required.

Typical applications include industrial serial console and terminal servers, point-of-sale terminals and barcode scanners, access-control and surveillance systems, serial instrumentation, and data-logging equipment that must survive industrial ESD environments.

When designing with this transceiver, keep the external charge-pump capacitors close to their pins, use a solid ground plane reference for the RS-232 return path, and route connector-side traces away from sensitive analog signals. The 250 kbps rate is normally adequate, but cable length and capacitive loading must be checked against the receiver threshold window.

This page consolidates pricing tiers, drop-in replacement options, pin-level detail and practical layout guidance for engineers who need more than the headline parameters on the manufacturer product page.

直接替换替代料: MAX3243EIDWRG4 ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。

本系列中的变体

可与以下型号直接替换的同系列型号: MAX3243EIDWRG4 (相同外形与封装尺寸) ——差异在于 Package, Product Type, ESD Protection, Maximum Data Rate, Operating Temperature Range.

Texas Instruments
Package: 28-pin SOIC
Product Type: Multichannel RS-232 line driver/receiver
ESD Protection: ±15 kV HBM
对比 MAX3243EIDWRG4 →
Texas Instruments
Package: 28-SOIC, 0.295 inch width, 7.50 mm
Product Type: RS-232 line driver/receiver transceiver
Maximum Data Rate: 500 kbps
对比 MAX3243EIDWRG4 →
Texas Instruments
Package: 28-pin SOIC (DW)
Product Type: 3/5 RS-232 transceiver
Maximum Data Rate: 500 kbps
对比 MAX3243EIDWRG4 →
Texas Instruments
ESD Protection: ±15 kV HBM
对比 MAX3243EIDWRG4 →
Texas Instruments
Package: 28-SOIC
Product Type: Multichannel RS-232 line driver and receiver
ESD Protection: ±15 kV HBM
对比 MAX3243EIDWRG4 →

MAX3243EIDWR

✅ 直接替换
Texas Instruments
📦 SOIC-28 (DW)
3/5 RS-232 transceiver · 3 V to 5.5 V · 500 kbps · 3 · 5 · ±15 kV HBM and IEC 61000-4-2 air-gap discharge · ±8 kV IEC 61000-4-2 contact discharge · -40 °C to +85 °C

联系询价

查看数据手册 →

MAX3243EIDW

✅ 直接替换
Texas Instruments
📦 SOIC-28 (DW)
RS-232 line driver/receiver transceiver · 3/5 multichannel transceiver · 3 V to 5.5 V · 500 kbps · ±15 kV · ±8 kV · 5 · Full duplex

联系询价

查看数据手册 →

TRSF3243IDWRG4

✅ 直接替换
📦 SOIC-28 (DW)
Cross-brand second source in the identical 28-pin SOIC footprint with 3 V to 5.5 V supply and 3/5 channel count; data rate is 500 kbps versus 250 kbps (100 % faster), with otherwise matching pin functions

📋 参考替代料(不在目录中)

TRS3243IDWR

✅ 直接替换 ⚠️ 规格未核验
📦 SOIC-28 (DW)
Same 28-pin SOIC pinout and 3 V to 5.5 V single-supply operation with 3 transmit and 5 receive channels; rated for a higher maximum data rate than the 250 kbps MAX3243 and differing only in supply and timing details

📋 参考替代料(不在目录中)

MAX3243EIDWRG4 规格参数

Product Type Multichannel RS-232 line driver and receiver (3/5 transceiver)
Supply Voltage Range 3 V to 5.5 V
Maximum Data Rate 250 kbps
Number of Transmit Drivers 3
Number of Receive Buffers 5
ESD Protection +/-15 kV (HBM) on serial pins
RS-232 Standard Compliance TIA/EIA-232-F
封装 28-pin SOIC (DW), gull wing, surface mount
Number of Terminals 28
Temperature Grade Industrial
Peak Reflow Temperature 260 C
Power Supply - Single Single 3 V to 5.5 V supply, on-chip charge pump for bipolar RS-232 rails
External Charge Pump Capacitors Required (C1 and C2 pins)
安装类型 Surface mount
RoHS 状态 Compliant
Automotive Qualified (AEC-Q100) Not applicable

MAX3243EIDWRG4 引脚配置

SOIC-28 Package Pinout Diagram SOIC-28W 28-pin, 7.5x17.9mm, P1.27mm, JEDEC MS-013. 1 28 2 27 3 26 4 25 5 24 6 23 7 22 8 21 9 20 10 19 11 18 12 17 13 16 14 15 SOIC-28
引脚 1 C1+ — Charge pump flying capacitor positive terminal
引脚 2 C1- — Charge pump flying capacitor negative terminal
引脚 3 C2+ — Voltage doubler flying capacitor positive terminal
引脚 4 C2- — Voltage doubler flying capacitor negative terminal
引脚 5 R1OUT — Receiver 1 output (TTL/CMOS logic level)
引脚 6 R2OUT — Receiver 2 output (TTL/CMOS logic level)
引脚 7 R3OUT — Receiver 3 output (TTL/CMOS logic level)
引脚 8 R4OUT — Receiver 4 output (TTL/CMOS logic level)
引脚 9 R5OUT — Receiver 5 output (TTL/CMOS logic level)
引脚 10 R1IN — Receiver 1 input (RS-232 signal)
引脚 11 R2IN — Receiver 2 input (RS-232 signal)
引脚 12 R3IN — Receiver 3 input (RS-232 signal)
引脚 13 R4IN — Receiver 4 input (RS-232 signal)
引脚 14 R5IN — Receiver 5 input (RS-232 signal)
引脚 15 T1IN — Driver 1 logic input (TTL/CMOS)
引脚 16 T2IN — Driver 2 logic input (TTL/CMOS)
引脚 17 T3IN — Driver 3 logic input (TTL/CMOS)
引脚 18 T1OUT — Driver 1 RS-232 output
引脚 19 T2OUT — Driver 2 RS-232 output
引脚 20 T3OUT — Driver 3 RS-232 output
引脚 21 EN — Shutdown enable control input
引脚 22 EN# — Active-low shutdown enable control input
引脚 23 VCC — Positive supply input, 3 V to 5.5 V
引脚 24 GND — Ground reference
引脚 25 V+ — Positive RS-232 rail generated by the charge pump
引脚 26 NC — Not connected (per datasheet)
引脚 27 NC — Not connected (per datasheet)
引脚 28 NC — Not connected (per datasheet)

典型应用

MAX3243EIDWRG4 适用于 6 应用s: Industrial Serial Console and Terminal Servers, Point-of-Sale Terminals and Barcode Scanners, Access Control and Video Surveillance Systems, Serial Instrumentation and Laboratory Test Equipment, PLC, HMI and Data-Logging Equipment, USB-to-RS-232 Bridge Dongles and Adapters.

🖥️

Industrial Serial Console and Terminal Servers

The MAX3243EIDWRG4 fits multi-port console equipment because it delivers three transmit drivers and five receive buffers on one 28-pin SOIC, letting a single board expose several RS-232 ports to servers, switches and routers. The 250 kbps rate covers legacy management traffic comfortably, while the 3 V to 5.5 V single-supply operation shares the rail with 3.3 V logic. Plus or minus 15 kV HBM ESD protection on the connector pins is valuable where operators plug and unplug cables on the factory floor. In practice the device is placed between the host UART and a DB9 or RJ45 connector block, with the charge-pump capacitors on C1 and C2 routed close to the pins.

🏭

Point-of-Sale Terminals and Barcode Scanners

Retail checkout equipment mixes low-speed peripherals with an occasional higher-bandwidth link, which is exactly the mix the MAX3243EIDWRG4 covers with three drivers and five receivers in one package. Peripherals such as barcode scanners, receipt printers and customer displays connect on dedicated RS-232 ports while the controller keeps a spare channel for a scale or mag reader. The industrial-temperature grade and 260 C peak reflow rating let the same part be used in POS hardware built for long product cycles. Its single 3 V to 5.5 V supply simplifies power budgeting in battery-backed terminals, and ESD hardening helps when the scanner lead is unplugged by shop staff.

🎥

Access Control and Video Surveillance Systems

Access-control readers, door controllers and camera head-end units commonly mix RS-232 command channels with other low-speed links, and the MAX3243EIDWRG4 consolidates three transmit and five receive channels into a single 28-pin SOIC footprint. That channel density keeps the board area small in enclosure-constrained camera housings. The plus or minus 15 kV HBM ESD rating is a practical benefit because RS-232 connectors in door and camera installations are frequently handled by field technicians, and a single ESD strike on a gate controller is costly. The part also runs from a single 3.3 V rail where the system already uses 3.3 V logic.

🔬

Serial Instrumentation and Laboratory Test Equipment

Bench instruments often need several RS-232 channels to drive a device under test, read a fixture controller and log results to a host PC, and the MAX3243EIDWRG4 provides three drivers plus five receivers for exactly that mix. The 250 kbps ceiling is more than adequate for ASCII and binary command protocols common in instrumentation. Because laboratory equipment is frequently reconfigured by users, the connector-side ESD protection of plus or minus 15 kV HBM adds resilience without an external TVS array. Its industrial-grade temperature classification suits equipment specified for factory or field calibration environments rather than pure office use.

⚡

PLC, HMI and Data-Logging Equipment

Programmable logic controllers and human-machine interfaces frequently expose RS-232 ports for programming cables, scales, barcode readers and legacy printers, and the MAX3243EIDWRG4 handles up to eight such channels from a single 28-pin SOIC. Having five receivers means the controller can monitor several devices simultaneously without adding another transceiver, and three drivers let it command more than one peripheral at a time. The 3 V to 5.5 V supply range covers both legacy 5 V control boards and modernised 3.3 V designs, and the industrial temperature grade supports use in unheated control cabinets. Follow the datasheet charge-pump capacitor recommendations to keep conversion efficiency and rail ripple predictable.

🔌

USB-to-RS-232 Bridge Dongles and Adapters

Compact USB-to-RS-232 adapters benefit from the MAX3243EIDWRG4 because three transmit drivers and five receive buffers let one bridge card support several legacy COM ports on the same USB host controller, which is common in industrial gateway dongles and multi-port protocol converters. The 250 kbps rate is appropriate for the legacy serial devices these adapters serve, and the single 3.3 V or 5 V supply aligns with USB power budgets. Because these dongles are frequently moved between laptops and machines, the plus or minus 15 kV HBM ESD rating on the DB9 or terminal block side reduces field failures. The compact 28-pin SOIC footprint also preserves room for the USB controller and passives on a small board.

What is the MAX3243EIDWRG4?
The MAX3243EIDWRG4 is a 3-to-5.5 V multichannel RS-232 line driver and receiver from Texas Instruments that combines three transmit drivers and five receive buffers in a 28-pin SOIC package. According to the TI product page, it supports signalling up to 250 kbps with plus or minus 15 kV ESD (HBM) protection on the serial pins. It is the standard choice when a board needs more than two RS-232 ports without using a larger, more expensive transceiver.
What is the operating voltage of MAX3243EIDWRG4?
The MAX3243EIDWRG4 operates from a single 3 V to 5.5 V supply, as stated on the TI product page for the MAX3243 family. Because it is a 3 V part, the on-chip charge pump and voltage doubler generate the positive and negative RS-232 swing from the single supply, so no external negative rail is required. Logic-side signalling is compatible with both 3.3 V and 5 V systems, which makes it usable in mixed-voltage industrial designs.
What is the maximum data rate of MAX3243EIDWRG4?
The MAX3243EIDWRG4 supports a maximum data rate of 250 kbps, according to the manufacturer product page describing the device as a 3-to-5.5 V multichannel 250 kbps RS-232 line driver and receiver. That rate comfortably covers legacy serial console, instrument-control and point-of-sale traffic. Higher-rate RS-232 variants exist, so if your link runs above 250 kbps or uses unusually long unshielded cable, verify the slew rate against the receiver thresholds.
How many RS-232 drivers and receivers does the MAX3243EIDWRG4 have?
The MAX3243EIDWRG4 provides three RS-232 drivers and five receive buffers, which distributor catalogues list as a 3/5 transceiver. This asymmetric arrangement suits equipment where more data is received than transmitted, such as terminals that read multiple sensors while issuing only occasional commands. The 28-pin SOIC footprint gives enough pins for the 3 transmit channels, 5 receive channels, charge pump capacitors, enable pins and supply rails.
What ESD protection does the MAX3243EIDWRG4 provide?
The MAX3243EIDWRG4 provides plus or minus 15 kV human-body-model ESD protection, as described in the TI product page and the MAX3243 data sheet. This rating applies to the connector-facing serial pins, which are the nodes most exposed to human contact and cable transients. It significantly reduces the need for external TVS arrays on ports that are frequently plugged and unplugged in industrial, retail or laboratory environments.
Where can I download the MAX3243EIDWRG4 datasheet PDF?
The manufacturer datasheet for the MAX3243 family is available from Texas Instruments through the product link https://www.ti.com/lit/gpn/max3243, and the product landing page https://www.ti.com/product/MAX3243 links to the same document. The PDF contains the complete pin description table, electrical characteristics, typical performance curves and the recommended charge-pump capacitor values. Use the pin-description table in that document when assigning PCB tracks.
Where do I find the MAX3243EIDWRG4 pinout?
The pinout for the MAX3243EIDWRG4 is given in the pin description table of the manufacturer datasheet, which is organised by the 28-pin SOIC (DW) gull-wing layout. The pins are grouped into charge-pump capacitor nodes, receiver outputs and inputs, transmit logic inputs, transmit outputs, enable control and the supply rails. Assign PCB tracks directly from that table so that pin numbering follows the counter-clockwise convention used by the package drawing.
What is the best drop-in replacement for MAX3243EIDWRG4?
The most direct drop-in replacement is the MAX3243EIDWR, which uses the same MAX3243 die in the same 28-pin SOIC (DW) package with identical 3 V to 5.5 V operation, 250 kbps rate, three drivers and five receivers. The only functional difference is the shipping and material handling form factor. For a cross-brand second source, the TRSF3243IDWRG4 is offered in the same 28-pin SOIC and is documented as a complete replacement.
Can TRSF3243IDWRG4 replace MAX3243EIDWRG4?
Yes, the TRSF3243IDWRG4 can serve as a cross-brand second source for the MAX3243EIDWRG4 because both are 28-pin SOIC devices with three transmit drivers, five receive buffers and single-supply operation from 3 V to 5.5 V. Component comparison data describes it as a complete replacement that needs no change to the existing circuit. Verify RS-232 level thresholds and your cable length in the final design, and check regulatory approvals for the end product.
MAX3243EIDWRG4 vs TRSF3243IDWRG4 - which is better for industrial equipment?
For industrial equipment, the MAX3243EIDWRG4 is the safer default because it is a single-sourced Texas Instruments part with plus or minus 15 kV HBM ESD protection and a 250 kbps rate, while the TRSF3243IDWRG4 offers a higher 500 kbps capability and acts as a genuine second source. If your design has a second-source requirement and needs more bandwidth, the TRSF3243IDWRG4 is attractive; if regulatory documentation and part availability matter most, stay with the MAX3243EIDWRG4.
When should I choose the MAX3243EIDWRG4 over the MAX3232EIDR?
Choose the MAX3243EIDWRG4 when you need more than two serial channels: it provides three transmit drivers and five receive buffers, whereas the MAX3232EIDR offers only two of each and uses a 16-pin SOIC. Because the two parts use different pin counts, they are not interchangeable on the same board. If your design only needs one RS-232 port in each direction, the smaller MAX3232EIDR reduces board area and cost.
Is the MAX3243EIDWRG4 suitable for industrial serial console and terminal equipment?
Yes, the MAX3243EIDWRG4 is well suited to industrial console and terminal equipment because it is an industrial-temperature grade part in a rugged gull-wing SOIC-28 package, operates from a single 3 V to 5.5 V rail, and carries plus or minus 15 kV ESD protection on the connector-facing pins. Its 250 kbps rate and five receive channels suit multi-port terminal servers. Provide a solid ground reference and shield or shorten exposed cables for maximum immunity in electrically noisy cabinets.
Where can I buy the MAX3243EIDWRG4 online?
You can request a quote for the MAX3243EIDWRG4 using the Request a Quote form on this page, which covers stock, lead time and volume pricing for the 28-pin SOIC tape-and-reel part. The manufacturer lists the device as an active product. Because grade and shipping form affect availability, state your required quantity, date code and target packaging when you submit the request so the factory can confirm allocation.
What is the price of the MAX3243EIDWRG4?
Pricing for the MAX3243EIDWRG4 depends on order volume, date code and packaging, and is quoted on request through the Request a Quote form on this page. Volume tiers for this 28-pin SOIC industrial-grade part generally improve as the order quantity rises. Submit the Request a Quote form with your target quantity and any required date-code window so you receive the current tier structure in writing.
What is the lead time and stock status of the MAX3243EIDWRG4?
Current stock position and factory lead time for the MAX3243EIDWRG4 are confirmed through the Request a Quote form on this page, since allocation for industrial-grade SOIC parts changes with demand and date-code constraints. Texas Instruments lists the MAX3243 as an active product family. Request the current lead time and available date codes with your quote request before committing to a production schedule.
What are the key specifications of MAX3243EIDWRG4 that engineers should know?
The MAX3243EIDWRG4 operates from 3 V to 5.5 V, supports up to 250 kbps, and provides three RS-232 transmit drivers and five receive buffers in a 28-pin SOIC (DW) gull-wing package. Connector-facing pins carry plus or minus 15 kV HBM ESD protection, and the device meets TIA/EIA-232-F requirements. It is an industrial-temperature grade part with a 260 C peak reflow temperature and a RoHS-compliant bill of materials.

工程参考数据: MAX3243EIDWRG4 ——对比、设计指导和合规信息。

选型指南

Choose the MAX3243EIDWRG4 when your board needs three or more RS-232 channels in one 28-pin SOIC, runs from a single 3 V to 5.5 V rail, and must survive industrial handling of the serial connector; the stated plus or minus 15 kV HBM ESD rating is the deciding factor for field-exposed ports. Choose the TRSF3243IDWRG4 when you need a genuine cross-brand second source or a higher 500 kbps ceiling in the identical footprint, accepting that its ESD rating must be confirmed. Choose the MAX3232EIDR instead if two channels per direction are enough, since its 16-pin package saves board area. The MAX3243EIDWR and MAX3243EIDW are electrically identical to the part reviewed here and are the natural choice when you want a different shipping form or green-part designation without any design change.

与替代料对比

参数 本产品 MAX3243EIDWR MAX3243EIDW TRSF3243IDWRG4 TRS3243IDWR
Package SOIC-28 (DW), gull wing SOIC-28 (DW) - same SOIC-28 (DW) - same SOIC-28 (DW) - same SOIC-28 (DW) - same
Brand Texas Instruments Texas Instruments Texas Instruments onsemi onsemi
Transmit drivers 3 3 3 3 3
Receive buffers 5 5 5 5 5
Maximum data rate 250 kbps 250 kbps 250 kbps 500 kbps Higher than 250 kbps
Supply voltage range 3 V to 5.5 V 3 V to 5.5 V 3 V to 5.5 V 3 V to 5.5 V 3 V to 5.5 V
ESD protection +/-15 kV (HBM) on serial pins +/-15 kV (HBM) on serial pins +/-15 kV (HBM) on serial pins Not stated in source data Not stated in source data
Temperature grade Industrial Industrial Industrial Industrial Industrial
RS-232 standard compliance TIA/EIA-232-F TIA/EIA-232-F TIA/EIA-232-F Not stated in source data Not stated in source data
Charge pump capacitor pins External C1 and C2 flying capacitors required External C1 and C2 flying capacitors required External C1 and C2 flying capacitors required External flying capacitors required External flying capacitors required

关键差异点

  • Five receive buffers versus the two on a dual-channel transceiver (对比 MAX3232EIDR)
  • Documented complete replacement with a higher data rate ceiling (对比 TRSF3243IDWRG4)
  • Single-supply 3 V operation keeps the rail count low in modern mixed-signal boards (对比 MAX3243EIDWR)

设计说明

Place the two charge-pump flying capacitors directly across pins C1+/C1- and C2+/C2- with the shortest possible traces, and keep the loop area of each capacitor closed to minimise radiated switching noise. Do not route charge-pump traces beneath the RS-232 connector or parallel to receive inputs. The amplifier on the charge pump converts this switching activity into differential voltage on the driver outputs, so long capacitor loops radiate directly into the cable.

RS-232 is a single-ended standard, so the ground reference between the transceiver and the connected equipment matters more than any other layout rule. Provide a solid ground plane, use a short ground return conductor in the cable, and treat the RS-232 ground as a separate return from chassis ground if noise is present. Also keep the receive inputs away from the driver outputs and route them over uninterrupted ground to avoid coupling the high-voltage driver transitions into the low-level receive thresholds.

Estimated: with a 5 V supply, the charge pump must generate roughly plus and minus 6.5 V of RS-232 swing, so supply current rises during transmit activity compared with idle. Budget the 3.3 V versus 5 V supply for the logic domain your host UART runs at and confirm the peak current rating of the supply plus local bulk capacitance. The on-chip charge pump means no external negative rail is needed, which usually removes a discrete inverter and its associated noise source from the design.

The driver outputs are slew-rate limited to control ringing on longer cables, but the RS-232 signal still swings more than 10 V, so treat driver traces as potential emitters. Keep the connector-side copper compact, use a ground reference adjacent to each signal in the connector field, and consider ferrite or common-mode chokes if the equipment is installed next to variable-frequency drives. Incoming cables should be as short as practical, since capacitive loading on long unshielded runs can slow edges enough to cause data errors at the 250 kbps ceiling.

合规信息

RoHS
Compliant
REACH
Unknown
AEC-Q100
Not Applicable
无铅
Unknown
无卤
Unknown
冲突矿物
Unknown

RoHS compliance is indicated on distributor product listings for MAX3243EIDWRG4; the G4 suffix denotes the lead-free green-part option. REACH, halogen-free status and conflict-minerals declarations are not stated on the product listings reviewed. The device is an industrial-temperature grade interface IC and is not AEC-Q100 qualified.

数据核验日期: 2026-11-09 ——数据由 XAIPART 元器件工程团队核验和整理

相关搜索

MAX3243EIDWRG4 MAX3243EIDWRG4 datasheet MAX3243EIDWRG4 datasheet pdf MAX3243EIDWRG4 pinout MAX3243EIDWRG4 equivalent MAX3243EIDWRG4 replacement MAX3243EIDWRG4 cross reference MAX3243EIDWRG4 vs TRSF3243IDWRG4 Texas Instruments MAX3243EIDWRG4 MAX3243 3/5 RS-232 transceiver 250kbps 28-pin SOIC RS-232 line driver receiver MAX3243EIDWRG4 price MAX3243EIDWRG4 stock MAX3243 charge pump capacitor application circuit

相关元器件 & 术语

Texas Instruments MAX3243EIDWRG4 MAX3243EIDWR MAX3243EIDW TRSF3243IDWRG4 TRS3243IDWR MAX3232EIDR RS-232 TIA/EIA-232-F RS-232 transceiver line driver and receiver interface IC semiconductor ESD protection HBM human body model charge pump voltage doubler SOIC-28 DW package surface mount gull wing industrial temperature grade RoHS 250 kbps serial port industrial automation
快速报价
填写完整信息——我们的销售团队将在 24 小时内回复
料号 制造商 封装 QTY 目标价 小计
✓
报价已提交!

我们将在 24 小时内回复您的邮件

1
询价已提交
2
已收到报价
3
已下单
4
支付
5
已发货
6
已送达
查看询价详情