MC9S08AW32VFUE - HCS08 8-bit MCU, 32KB Flash, 40MHz, 64-QFP
料号： MC9S08AW32VFUE ✗ 停产| 数量 | 单价 | 小计 |
|---|---|---|
| 1 | $9.8 | $9.80 |
| 10 | $8.85 | $88.50 |
| 100 | $7.95 | $795.00 |
| 500 | $7.1 | $3,550.00 |
| 1,000 | $6.4 | $6,400.00 |
MC9S08AW32VFUE 概述
An 8-bit MCU is a programmable computing engine that fetches and executes instructions from on-chip memory; the HCS08 core is a Von Neumann architecture with a 16-bit address space and an enhanced instruction set targeting low-power, deterministic embedded control. Within the broader taxonomy, this part is an MCU -> microcontroller -> embedded processor -> semiconductor device. The S08 family is widely adopted in industrial and automotive subsystems where deterministic real-time response and on-chip analog integration outweigh raw compute throughput.
Key features of the MC9S08AW32VFUE include 32KB of Flash program memory, 2KB of RAM, an internal clock synthesizer supporting bus rates up to 20 MHz, an integrated 10-bit ADC with up to 12 input channels, multiple PWM-capable timers, an SPI module, two SCI (UART) modules, and an I2C module. Operation from 2.7V to 5.5V supply allows direct compatibility with both 3.3V and 5V systems.
The S08 core uses a Harvard-style instruction pipeline and supports background debug mode (BDM) via a single-wire interface, enabling in-circuit programming and non-intrusive debug. The peripheral set includes a real-time counter (RTC), a computer operating properly (COP) watchdog, low-voltage detect (LVD) with reset, and multiple general-purpose I/O ports. The Flash controller supports in-application reprogramming with built-in security for code protection.
Typical applications include industrial control, automotive body and chassis modules, consumer appliances, sensor signal conditioning, and motor control (PWM-driven). The integrated ADC and timers make it suitable for closed-loop temperature, pressure, and flow regulation.
When designing with this MCU, allocate ground and supply decoupling close to every VDD/VSS pair (typically 100 nF + bulk capacitor) and keep the BDM pin accessible for production programming. For automotive deployments, observe NXP's EMC and ESD guidelines for body electronics.
This page synthesizes NXP S08AW family datasheet parameters, distributor pricing, drop-in alternatives within the same family, and PCB-level design notes not consolidated in the manufacturer datasheet alone.
直接替换替代料： MC9S08AW32VFUE ——相同封装，引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号： MC9S08AW32VFUE （相同外形与封装尺寸） ——差异在于 Package, Core, Debug Interface, I/O Ports, Operating Temperature.
快速对比工具——选择替代料号进行并排对比：
MC9S08AW32CFUE
✅ 直接替换✓ 有现货
$7.18 / 个
查看数据手册 →MC9S08AW48CFGER
✅ 直接替换✓ 有现货
$4.05 / 个
查看数据手册 →MC9S08AW60CFUE
✅ 直接替换✓ 有现货
$8.1029 / 个
查看数据手册 →MC9S08AW60CFGER
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料（不在目录中）
S9S08AW8AE0MLC
✅ 直接替换✓ 有现货
联系询价
查看数据手册 →MC9S08AW32VFUE 最大额定值与电气特性
| Core | HCS08 (S08 CISC) |
| 数据总线宽度 | 8-bit |
| 最大时钟频率 | 40 MHz |
| Program Memory Size | 32 KB Flash |
| RAM Size | 2 KB |
| Supply Voltage Range | 2.7 V to 5.5 V |
| ADC | 10-bit, up to 12 channels |
| Timers | TPM1, TPM2 (PWM), RTI, PIT |
| Communication Interfaces | 1x SPI, 2x SCI (UART), 1x I2C |
| I/O Pins | 54 general-purpose I/O |
| 封装 | 64-QFP (14x14 mm) |
| 安装类型 | Surface Mount |
| 工作温度 | -40 C to +105 C |
| Debug Interface | Background Debug Mode (BDM) |
| RoHS 状态 | Compliant |
MC9S08AW32VFUE 引脚配置
| 引脚 1 | PTD5/TxD2 — Port D5 / SCI2 transmit (VFUE package pinout per family datasheet) |
| 引脚 2 | PTD4/RxD2 — Port D4 / SCI2 receive |
| 引脚 3 | PTD3/SS1 — Port D3 / SPI1 slave select |
| 引脚 4 | VDD1 — Power supply pin 1 |
| 引脚 5 | VSS1 — Ground pin 1 |
| 引脚 6 | PTD2/MISO1 — Port D2 / SPI1 MISO |
| 引脚 7 | PTD1/MOSI1 — Port D1 / SPI1 MOSI |
| 引脚 8 | PTD0/SPSCK1 — Port D0 / SPI1 clock |
| 引脚 9 | PTE7/TxD1 — Port E7 / SCI1 transmit |
| 引脚 10 | PTE6/RxD1 — Port E6 / SCI1 receive |
| 引脚 11 | PTE5 — Port E5 general I/O |
| 引脚 12 | PTE4 — Port E4 general I/O |
| 引脚 13 | BKGD — Background Debug Mode pin |
| 引脚 14 | RESET — External reset, active low |
| 引脚 15 | PTG0 — Port G0 general I/O |
| 引脚 16 | PTH0 — Port H0 general I/O |
| 引脚 17 | VDD2 — Power supply pin 2 |
| 引脚 18 | VSS2 — Ground pin 2 |
| 引脚 19 | PTF7/ADC7 — Port F7 / ADC channel 7 |
| 引脚 20 | PTF6/ADC6 — Port F6 / ADC channel 6 |
| 引脚 21 | PTF5/ADC5 — Port F5 / ADC channel 5 |
| 引脚 22 | PTF4/ADC4 — Port F4 / ADC channel 4 |
| 引脚 23 | PTF3/ADC3 — Port F3 / ADC channel 3 |
| 引脚 24 | PTF2/ADC2 — Port F2 / ADC channel 2 |
| 引脚 25 | PTF1/ADC1 — Port F1 / ADC channel 1 |
| 引脚 26 | PTF0/ADC0 — Port F0 / ADC channel 0 |
| 引脚 27 | VREFH — ADC high reference |
| 引脚 28 | VREFL — ADC low reference |
| 引脚 29 | PTB7/AD15 — Port B7 / ADC channel 15 |
| 引脚 30 | PTB6/AD14 — Port B6 / ADC channel 14 |
| 引脚 31 | PTB5/AD13 — Port B5 / ADC channel 13 |
| 引脚 32 | PTB4/AD12 — Port B4 / ADC channel 12 |
| 引脚 33 | PTC3 — Port C3 general I/O |
| 引脚 34 | PTC2 — Port C2 general I/O |
| 引脚 35 | PTC1 — Port C1 general I/O |
| 引脚 36 | PTC0 — Port C0 general I/O |
| 引脚 37 | PTA7/TPM2CH3 — Port A7 / TPM2 channel 3 |
| 引脚 38 | PTA6/TPM2CH2 — Port A6 / TPM2 channel 2 |
| 引脚 39 | PTA5/TPM2CH1 — Port A5 / TPM2 channel 1 |
| 引脚 40 | PTA4/TPM2CH0 — Port A4 / TPM2 channel 0 |
| 引脚 41 | PTA3/TPM1CH3 — Port A3 / TPM1 channel 3 |
| 引脚 42 | PTA2/TPM1CH2 — Port A2 / TPM1 channel 2 |
| 引脚 43 | PTA1/TPM1CH1 — Port A1 / TPM1 channel 1 |
| 引脚 44 | PTA0/TPM1CH0 — Port A0 / TPM1 channel 0 |
| 引脚 45 | PTB3/AD11 — Port B3 / ADC channel 11 |
| 引脚 46 | PTB2/AD10 — Port B2 / ADC channel 10 |
| 引脚 47 | PTB1/AD9 — Port B1 / ADC channel 9 |
| 引脚 48 | PTB0/AD8 — Port B0 / ADC channel 8 |
| 引脚 49 | PTG7 — Port G7 general I/O |
| 引脚 50 | PTG6 — Port G6 general I/O |
| 引脚 51 | PTG5 — Port G5 general I/O |
| 引脚 52 | PTG4 — Port G4 general I/O |
| 引脚 53 | PTG3 — Port G3 general I/O |
| 引脚 54 | PTG2 — Port G2 general I/O |
| 引脚 55 | PTG1 — Port G1 general I/O |
| 引脚 56 | PTH1 — Port H1 general I/O |
| 引脚 57 | PTH2 — Port H2 general I/O |
| 引脚 58 | PTH3 — Port H3 general I/O |
| 引脚 59 | PTH4 — Port H4 general I/O |
| 引脚 60 | PTH5 — Port H5 general I/O |
| 引脚 61 | PTH6 — Port H6 general I/O |
| 引脚 62 | PTH7 — Port H7 general I/O |
| 引脚 63 | VDD3 — Power supply pin 3 |
| 引脚 64 | VSS3 — Ground pin 3 |
典型应用
MC9S08AW32VFUE 适用于 6 应用s: Industrial Control Modules, Automotive Body Electronics, Consumer Appliance Control, Sensor Signal Conditioning, Motor Control (PWM-Driven), Battery Charging / Power Management Controllers.
Industrial Control Modules
Why the MC9S08AW32VFUE fits: Industrial modules demand deterministic 8-bit processing, robust peripheral integration, and wide supply tolerance - the S08AW delivers 40 MHz core, 32 KB Flash for control firmware, 2 KB RAM for stack/buffers, and a 10-bit ADC with 12 channels for sensor conditioning across 2.7-5.5 V. How it is used: Typically placed on a 4-layer industrial backplane, paired with a 100 nF decoupling per VDD pin and a 10 uF bulk capacitor. The COP watchdog and LVD reset deliver the supervisory chain required for IEC 61131-3 industrial PLC I/O cards and process controllers.
推荐
Automotive Body Electronics
Why the MC9S08AW32VFUE fits: The -40 C to +105 C operating range covers cabin and body-domain ECUs (RKE, BCM, seat controllers, HVAC). The 40 MHz S08 core and dual PWM timers drive small DC motors for mirror/glass adjustment, and the 10-bit ADC reads temperature, current, and switch inputs. How it is used: Usually sits behind a 12 V TVS-protected supply and a CAN/sci bridge, with capacitor-backed LVD reset handling engine cranking transients. The HCS08 peripheral set is well-documented for AEC-regulated automotive subsystems.
推荐
Consumer Appliance Control
Why the MC9S08AW32VFUE fits: White goods (washing machines, dishwashers, HVAC thermostats) need reliable keypad/LED drivers, motor PWM, and serial supervisory links - all present on the S08AW. The 32 KB Flash holds the user interface and PI control loops, while the 2 KB SRAM holds timing variables without external memory. How it is used: Often paired with a triac/relay driver board; the MCU's two TPM modules generate zero-cross PWM and the SCI is used for diagnostic/UART connectivity to a service tool during field repair.
推荐
Sensor Signal Conditioning
Why the MC9S08AW32VFUE fits: The 10-bit ADC with up to 12 channels lets designers digitize thermistor bridges, pressure sensors, and analog encoder signals directly; the S08 core supports linearization and digital filtering in firmware. 32 KB Flash provides ample memory for lookup tables. How it is used: Placed adjacent to a low-noise LDO and an instrumentation preamp, the MCU issues periodic ADC reads, applies compensation, and outputs the cleaned value over SPI or UART to a host PLC.
推荐
Motor Control (PWM-Driven)
Why the MC9S08AW32VFUE fits: Two TPM channels deliver complementary or center-aligned PWM to drive brushed DC, stepper, or small BLDC motors; the 40 MHz core leaves headroom for space-vector modulation or trapezoidal commutation. Current sensing via the 10-bit ADC closes the torque loop. How it is used: Typically inserted between a half-bridge driver (such as MC33931) and the H-bridge stage. Speed command received via UART or potentiometer input, with firmware filtering on the ADC line.
推荐
Battery Charging / Power Management Controllers
Why the MC9S08AW32VFUE fits: Smart charging subsystems (e-bike BMS, telecom backup float chargers) require accurate ADC sampling and deterministic PWM - the S08AW integrates both with the COP watchdog supervising the charging state machine. 32 KB Flash holds multi-stage charge profiles. How it is used: Placed across the shunt resistor of the battery stack, with a Hall-effect current sensor for total current. The SCI reports telemetry to a fuel-gauge host. The wide 2.7-5.5 V supply allows direct operation from battery-pack tap points.
推荐
推荐产品汇总
工程参考数据： MC9S08AW32VFUE ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | MC9S08AW32CFUE | MC9S08AW48CFGER | MC9S08AW60CFUE | MC9S08AW60CFGER | S9S08AW8AE0MLC |
|---|---|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | 64-QFP (14x14 mm) | 64-LQFP (14x14 mm) | 64-LQFP (14x14 mm) | 64-LQFP (14x14 mm) | 64-LQFP (10x10 mm) | 64-LQFP (10x10 mm) |
| Core | HCS08 8-bit | HCS08 8-bit | HCS08 8-bit | HCS08 8-bit | HCS08 8-bit | S08 8-bit |
| Clock Frequency | 40 MHz | 40 MHz | 40 MHz | 40 MHz | 40 MHz | 20 MHz |
| Flash Memory | 32 KB | 32 KB | 48 KB | 60 KB | 60 KB | 8 KB |
| RAM | 2 KB | 2 KB | 2 KB | 2 KB | 2 KB | 1 KB |
| Supply Voltage | 2.7 V to 5.5 V | 2.7 V to 5.5 V | 2.7 V to 5.5 V | 2.7 V to 5.5 V | 2.7 V to 5.5 V | 2.7 V to 5.5 V |
| Operating Temperature | -40 C to +105 C | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C | -40 C to +125 C |
| Lifecycle Status | NRND | Active | Active | Active | Active | NRND |
关键差异点
- Highest Flash density in NXP's S08AW fielded line （对比 S9S08AW8AE0MLC)
- Wider operating temperature for automotive body ECUs （对比 MC9S08AW32CFUE)
- Drop-in upgrade path to 60 KB Flash on same family （对比 MC9S08AW60CFUE)
设计说明
Estimated: The S08AW has three VDD/VSS pairs (Vpp=5V). Place a 100 nF ceramic decoupling capacitor within 5 mm of each VDD/VSS pair, plus a single 10 uF bulk capacitor on the board. Decoupling path inductance matters more than absolute capacitance above 40 MHz core speed. For 5V operation NXP recommends a linear regulator with <50 mV ripple; switching regulators require a Pi-filter (LC) to prevent MCU core noise coupling.
Route the BKGD/DEBUG pin away from high-current switching traces; AC-couple noise on BKGD can disrupt in-circuit programming. Maintain 50 ohm impedance on the BDM cable for production-line reliability. The 64-QFP at 14x14 mm has 0.8 mm pitch; use a 4-layer PCB with 5-7 mil traces/5-7 mil spaces on outer layers to fan out from pads. Add a copper pour connected to VSS beneath the chip and stitch it to ground vias around the periphery for thermal dissipation and shielding.
Do not leave the RESET pin floating: tie to VDD through a 10 kohm resistor with a 100 nF capacitor to ground for noise immunity, OR drive it with a dedicated supervisor. NRND does not mean defective - S08AW parts still reach production volumes, but lead time may stretch to 12-16 weeks. Validate alternate sources (NXP authorised distributor) in your BOM before committing new designs. Watch Flash write timing carefully: in-application programming needs the recommended 4.5 V min VDD for guaranteed writes below 0 C.
The HCS08 core has tight ADC sample timing; keep the analog and digital grounds separate and join at a single star point near the MCU VSS3 (pin 64). The ADC reference pins VREFH/VREFL should each have a 100 nF ceramic plus a 10 uF bypass capacitor - omitting the bulk capacitor introduces temperature drift above 80 C. For 10-bit absolute accuracy at full sampling rate (240 kHz), keep analog trace length to the ADC pins under 25 mm.
合规信息
RoHS compliant per NXP product page and supplier documentation. Not AEC-Q100 qualified (industrial and body-domain only); for powertrain-grade automotive use, select Kinetis or S12 family.