SI5366-C-GQ - 1.05GHz Jitter Attenuator Clock Multiplier | Skyworks
料号： SI5366-C-GQ ✓ 量产中| 数量 | 单价 | 小计 |
|---|---|---|
| 1 | $42.5 | $42.50 |
| 10 | $38.9 | $389.00 |
| 100 | $34.75 | $3,475.00 |
| 500 | $31.2 | $15,600.00 |
| 1,000 | $28.6 | $28,600.00 |
SI5366-C-GQ 概述
A jitter attenuator is a specialized clock generator built around a phase-locked loop (PLL) that cleans reference clocks by narrowing their jitter distribution while synthesizing output frequencies. Within the timing hierarchy, the Si5366 belongs to the clock multiplier and frequency synthesizer family, positioned below full network synchronization cards but above simple zero-delay buffers, and it serves as the timing backbone for synchronous optical networking (SONET), Ethernet, and Fibre Channel line cards.
Key features include selectable output frequencies from 8 kHz to 1050 MHz, third-generation DSPLL technology, an integrated loop filter with selectable loop bandwidth from 60 Hz to 8.4 kHz, four clock inputs with manual or automatic hitless switching, and output logic levels selectable among CML, CMOS, LVDS, and LVPECL. The C-grade option delivers 0.3 ps rms typical jitter generation and meets OC-192 GR-253-CORE jitter specifications, making it suitable for the most demanding telecom compliance regimes.
Technically, the DSPLL architecture replaces conventional discrete RC loop filters with an on-chip digital loop filter, enabling precise bandwidth programmability without external components and superior tolerance of noisy references. Frequency plans are configured through in-circuit programming rather than factory pin-strapping, allowing one device to serve many clocking architectures.
Typical applications include SONET OC-48/OC-192 line-card clock recovery and synthesis, 10 Gigabit Ethernet PHY reference clocking, Fibre Channel storage-area-network switching, and telecom transport equipment requiring hitless reference switching between redundant sources.
A key design consideration is power supply integrity: high-speed CML and LVPECL outputs demand clean 2.5V/3.3V rails and solid ground planes; omitting proper decoupling at the PLL supply pins degrades the sub-picosecond jitter floor.
This page synthesizes distributor pricing, drop-in alternatives, design notes, and compliance data not found in the manufacturer datasheet alone.
直接替换替代料： SI5366-C-GQ ——相同封装，引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号： SI5366-C-GQ （相同外形与封装尺寸） ——差异在于 Input Frequency Range, Output Frequency Range, Package, Maximum Output Frequency, Packaging.
快速对比工具——选择替代料号进行并排对比：
SI5366-B-GQ
✅ 直接替换 ⚠️ 规格未核验✓ 有现货
联系询价
查看数据手册 →SI5366-A-GQ
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料（不在目录中）
SI5366-C-GQR
✅ 直接替换✓ 有现货
$14.22 / 个
查看数据手册 →SI5369A-C-GQ
✅ 直接替换📋 参考替代料（不在目录中）
SI5369B-C-GQ
✅ 直接替换📋 参考替代料（不在目录中）
SI5366-C-GQ 规格参数
| 功能 | Clock Multiplier, Jitter Attenuator |
| PLL | Yes (DSPLL, third generation) |
| Maximum Output Frequency | 1050 MHz (1.05 GHz) |
| Input Frequency Range | 8 kHz to 707 MHz |
| Output Frequency Range | 8 kHz to 1050 MHz |
| Number of Clock Inputs | 4 |
| Number of Clock Outputs | 5 |
| Jitter Generation | 0.3 ps rms typ (12 kHz to 20 MHz) |
| Output Logic Levels | CML, CMOS, LVDS, LVPECL |
| Loop Bandwidth | 60 Hz to 8.4 kHz (selectable, integrated loop filter) |
| Hitless Switching | Manual or automatically controlled |
| Standards Compliance | Meets OC-192 GR-253-CORE jitter specifications |
| 封装 | 100-TQFP |
| 安装类型 | Surface Mount |
SI5366-C-GQ 100-tqfp 引脚配置指南
SI5366-C-GQ（100-tqfp 封装）的引脚配置。 引脚编号、功能和连接图在制造商数据手册中定义。请参阅该手册以了解确切的封装尺寸和焊接指南。
暂无详细引脚数据： SI5366-C-GQ.
请参阅 数据手册 以查看完整引脚配置。
典型应用
SI5366-C-GQ 适用于 6 应用s: SONET OC-48/OC-192 Line Cards, 10 Gigabit Ethernet Switching, Fibre Channel SAN Switching, Telecom Synchronization and Timing Cards, Test and Measurement Instrumentation, Wireless Baseband and Radio Units.
SONET OC-48/OC-192 Line Cards
The SI5366-C-GQ was designed explicitly for SONET OC-48 and OC-192 transport systems, where transmit and receive clocks must satisfy ITU-T-derived GR-253-CORE jitter masks. Its C-grade 0.3 ps rms jitter generation (12 kHz to 20 MHz) provides margin against the OC-192 jitter generation limit, while the selectable 60 Hz to 8.4 kHz loop bandwidth aligns with SONET jitter transfer requirements. Four clock inputs with automatic hitless switching allow seamless transition between redundant timing references without output phase disturbance, a mandatory feature in carrier-grade line cards. The five outputs simultaneously serve the framer, SerDes, and mapper reference clocks from one cleaned timing source.
推荐
10 Gigabit Ethernet Switching
In 10GbE switch and router line cards, PHY and MAC reference clocks demand low phase noise to keep SerDes bit-error rates low across 64b/66b links. The SI5366-C-GQ synthesizes 156.25 MHz and 312.5 MHz LVPECL or LVDS outputs from a common reference with jitter generation as low as 0.3 ps rms, directly meeting typical 10G PHY phase-jitter mask requirements. Its any-frequency DSPLL means one inventory item covers 10GBASE-R, 40GBASE-R gear-train references, and legacy 1G timing. Automatic hitless input switching supports redundant sync-E/1588 timing sources without output glitches, and output logic-level selectability (CML, CMOS, LVDS, LVPECL) lets one part drive heterogeneous clock trees.
推荐
Fibre Channel SAN Switching
Fibre Channel switch fabrics require tightly controlled reference clocks at 1.0625 Gbps, 2.125 Gbps, and higher rates to sustain BER targets across retimed ports. The SI5366-C-GQ generates these Fibre Channel frequencies from a single reference using its DSPLL core, with integrated loop filter and selectable 60 Hz to 8.4 kHz bandwidth suppressing reference noise effectively. Because the datasheet explicitly lists Fibre Channel among its target systems, jitter compliance at these rates is characterized. The four-input hitless architecture also supports redundant fabric-clock cards, while five simultaneous outputs distribute timing to fabric, edge, and management ports from one device in the 100-TQFP footprint.
推荐
Telecom Synchronization and Timing Cards
Central-office synchronization supply units (SSUs) and BITS cards groom timing references derived from GPS, PRC, or T1/E1 spans. The SI5366-C-GQ accepts slow 8 kHz references and multiplies them to any output up to 1050 MHz, covering both legacy TDM distribution at 1.544/2.048 MHz rates and modern packet-timing PHY references. Hitless switching between four inputs protects against reference failures, and the narrow selectable loop bandwidth (down to 60 Hz) provides deep reference-noise filtering for wander-sensitive TDM output. Operating as the core of a timing card, one 100-TQFP device replaces discrete VCXO-plus-PLL chains and their manual loop-filter tuning.
推荐
Test and Measurement Instrumentation
Bit-error-rate testers, protocol analyzers, and jitter-tolerance test sets need programmable, ultra-clean clocks spanning thousands of standard rates. The SI5366-C-GQ's any-frequency DSPLL, programmable via serial interface, lets one instrument platform generate 8 kHz to 1050 MHz outputs on demand, including SONET/SDH, Ethernet, and Fibre Channel standard rates, with 0.3 ps rms jitter adequate as a measurement reference. Four inputs allow the instrument to lock to the device-under-test reference or an external house standard with hitless transition. The CML/LVDS/LVPECL/CMOS output selectability matches arbitrary DUT input requirements without level-shifting circuitry.
推荐
Wireless Baseband and Radio Units
LTE and 5G baseband cards synchronize data converters, FPGAs, and modems to a common low-jitter reference derived from fronthaul timing. The SI5366-C-GQ cleans an incoming SyncE/PTP-derived clock and synthesizes converter sampling clocks up to 1050 MHz with 0.3 ps rms jitter, preserving SNR in wideband ADCs and DACs whose aperture jitter converts to noise. Automatic hitless input switching maintains coherent timing when fronthaul references fail over. Its wide 8 kHz input acceptance also allows locking directly to slow synchronization pulses, and the selectable narrow loop bandwidth (60 Hz) suppresses packet-based phase noise before it reaches the converters.
推荐
推荐产品汇总
工程参考数据： SI5366-C-GQ ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | SI5366-B-GQ | SI5366-A-GQ | SI5366-C-GQR | SI5369A-C-GQ | SI5369B-C-GQ |
|---|---|---|---|---|---|---|
| Package | 100-TQFP | 100-TQFP - same | 100-TQFP - same | 100-TQFP - same | 100-TQFP - same | 100-TQFP - same |
| Brand | Skyworks Solutions | Skyworks Solutions | Skyworks Solutions | Skyworks Solutions | Skyworks Solutions | Skyworks Solutions |
| Drop-in Compatibility | Reference part | Pin-to-pin, grade change only | Pin-to-pin, grade change only | Identical die, reel packaging | Requires design re-verification | Requires design re-verification |
关键差异点
- Best jitter grade in the Si5366 family （对比 SI5366-B-GQ)
- Hitless input switching across four references （对比 SI5369A-C-GQ)
- Fully integrated loop filter （对比 SI5366-A-GQ)
设计说明
The SI5366-C-GQ's 0.3 ps rms jitter floor is achievable only with disciplined power distribution. Provide separate low-noise supply domains for the DSPLL analog core and each output-bank supply, decoupling each pin with 0.1 uF ceramic capacitors placed within 2 mm, plus bulk 10 uF per rail. Ferrite beads between the digital 3.3V rail and the PLL analog supply attenuate switching-regulator spurs that would otherwise modulate output phase. Estimated: a 20 mV rms supply ripple coupling to a typical PLL supply-pushing figure produces phase spurs well above the 0.3 ps noise budget, so linear post-regulation of the PLL rail is recommended for jitter-critical designs.
On the 100-TQFP land pattern, route LVPECL/CML outputs as 100-ohm differential pairs with length matching within 5 mil and a solid, unbroken reference plane beneath. Keep input reference clock traces away from output traces to avoid crosstalk-induced jitter, and surround the device ground pins with a dense via stitch to the ground plane. Place the series termination resistors for CML/LVPECL outputs close to the driver pins. Avoid routing other clock trees or fast digital buses directly under the Si5366; the DSPLL supply pins are the most sensitive nodes on the board.
Two frequent mistakes with the Si5366: first, assuming pin compatibility with the Si5369 family - although both are 100-TQFP Skyworks DSPLL parts, the Si5369 architecture and configuration differ, and substitution requires re-verification against the datasheet. Second, ignoring the frequency-plan configuration: outputs are set by programmed divider values, not pin straps, so a board brought up with default or stale register files will run at wrong frequencies. Validate the loop-bandwidth setting against your jitter-transfer requirement - a bandwidth set too wide passes reference noise through and defeats the attenuation purpose.
合规信息
Compliance status not stated in the retrieved source snippets; confirm via Skyworks product page or DigiKey part 2278217 before release.