SPC5606SF2CLU6 - 32-bit MCU, 1MB Flash, 64MHz, QFP-176 | NXP
料号： SPC5606SF2CLU6 ✓ 量产中| 数量 | 单价 | 小计 |
|---|---|---|
| 1 | $13.81 | $13.81 |
| 10 | $12.43 | $124.30 |
| 100 | $10.88 | $1,088.00 |
| 500 | $9.65 | $4,825.00 |
| 1,000 | $8.78 | $8,780.00 |
SPC5606SF2CLU6 概述
An automotive microcontroller (MCU) is a microprocessor unit qualified to operate reliably in the harsh electrical, thermal, and vibration environment of a vehicle, integrating one or more CPU cores, non-volatile program memory (Flash), volatile working memory (SRAM), and a heterogeneous peripheral set on a single die. SPC5606SF2CLU6 sits in the wider NXP Power Architecture MCU hierarchy (PowerPC e200 -> Qorivva MPC56xx -> MPC560xS cluster family) and targets mid-range instrument clusters that balance cost, performance, and integrated graphics/display peripherals over general-purpose automotive MCUs such as the MPC5566.
Key features include up to 64 MHz core frequency, 1 MB on-chip Flash program memory, an integrated TFT display controller (LCDC) and video DAC, enhanced modular I/O subsystem (eMIOS), multiple CAN 2.0B controllers (FlexCAN), SPI, I2C, UART/SCI, a 12-bit ADC and an enhanced queued analog-to-digital converter (eQADC) for precision sensor acquisition. The device integrates a stepper-motor driver interface for gauge movements and supports the SPC5Studio software ecosystem with AUTOSAR MCAL drivers, reference hardware platforms, and a hardware security module (HSE) for secure boot in production-grade deployments.
The SPC5606SF2CLU6 is built on a 90-nm non-volatile memory (NVM) CMOS process with an on-chip voltage regulator (low-voltage detection, power-on reset, and standby modes). A PLL provides the system clock, while independent peripheral clocks can be gated for active-power management. Memory protection and error-correcting code support contribute to functional safety compliance under ISO 26262 up to ASIL-B for instrument-cluster applications.
Typical applications are mid-range automotive instrument clusters with 5-inch to 7-inch TFT color panels, body control modules driving multiple stepper gauges, CAN-based gateway nodes, HVAC controllers with graphical displays, and aftermarket heads-up displays. The wide operating temperature range of -40C to +85C and AEC-Q100 qualification make it well-suited to cabin and engine-bay-adjacent locations.
When designing with this MCU, ensure a 4.7uF or larger bulk decoupling capacitor is placed near each VDD/VSS pair and that the analog and digital grounds return to a single low-impedance ground plane. Crystal layout must follow the short-trace, guard-ring rules described in the NXP hardware design guide to keep the PLL within its jitter mask. Software engineers should select the documented oscillator frequency (40 MHz external crystal is recommended) and configure the PLL through the SPC5Studio clock tool rather than overriding registers manually.
直接替换替代料： SPC5606SF2CLU6 ——相同封装，引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号： SPC5606SF2CLU6 （相同外形与封装尺寸） ——差异在于 Package, Series, Supply Voltage, Program Memory Size, RoHS Status.
快速对比工具——选择替代料号进行并排对比：
SPC5605SF2CLU6
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料（不在目录中）
SPC5607SF2CLU6
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料（不在目录中）
SPC5642AF2MLU1
✅ 直接替换 ⚠️ 规格未核验✓ 有现货
$21.23 / 个
查看数据手册 →SPC5644AF0MLU2
✅ 直接替换 ⚠️ 规格未核验✓ 有现货
$12.5 / 个
查看数据手册 →SPC5746BSK1MKU2
✅ 直接替换 ⚠️ 规格未核验✓ 有现货
$17.25 / 个
查看数据手册 →SPC5602BF2MLL6
✅ 直接替换 ⚠️ 规格未核验✓ 有现货
$5.59 / 个
查看数据手册 →SPC5606SF2CLU6 最大额定值与电气特性
| Manufacturer | NXP Semiconductors |
| Series | MPC560xS (Qorivva) |
| Core Architecture | Power Architecture e200z0h |
| Core Count | 1 |
| 数据总线宽度 | 32-bit |
| 最大时钟频率 | 64 MHz |
| Program Memory Size (Flash) | 1 MB (1024 KB) |
| 电源电压 | 3.3 V / 5 V |
| 工作温度范围 | -40C to +85C |
| 封装 / 外壳 | 176-LQFP (24x24 mm) |
| 安装类型 | Surface Mount |
| 引脚数 | 176 |
| Automotive Qualification | AEC-Q100 qualified |
| RoHS 状态 | Compliant |
| Terminal Form | GULL WING |
| Temperature Grade | INDUSTRIAL (automotive application) |
| Peripheral Highlights | FlexCAN, eMIOS, eQADC, SPI, I2C, SCI, LCDC |
SPC5606SF2CLU6 176-lqfp (24x24 mm) 引脚配置指南
SPC5606SF2CLU6（176-lqfp (24x24 mm) 封装）的引脚配置。 该数字 IC 包含 GPIO、通信接口（UART、SPI、I2C）和电源引脚。请参阅制造商数据手册以了解复用引脚功能和配置选项。对嵌入式系统设计和 PCB 布局至关重要。
暂无详细引脚数据： SPC5606SF2CLU6.
请参阅 数据手册 以查看完整引脚配置。
典型应用
SPC5606SF2CLU6 适用于 6 应用s: Automotive Instrument Cluster with TFT Display, Body Control Module (BCM), CAN Gateway / Network Hub, HVAC Control Unit with Graphical Display, Stepper-Motor Gauge Cluster, Industrial TFT Human-Machine Interface (HMI).
Automotive Instrument Cluster with TFT Display
The SPC5606SF2CLU6 is purpose-built for color TFT instrument clusters in mid-range vehicles, where its integrated LCD controller (LCDC) and dedicated video DAC drive 5 to 7-inch panels without an external graphics controller. The e200z0h core at 64 MHz sustains automotive-grade real-time workloads: pointer driving, RPM/speed rendering, telltale animation, and CAN message processing at 500 kbps. Compared with a discrete MCU + external GPU approach, the SPC5606SF2CLU6 reduces PCB area, lowers BOM cost, and shortens software bring-up by keeping the display pipeline in peripheral hardware rather than the CPU.
推荐
Body Control Module (BCM)
In BCM applications the SPC5606SF2CLU6 acts as the central node aggregating CAN/LIN messages from door modules, lighting controllers, and HVAC units. Its multiple FlexCAN 2.0B controllers, eMIOS timer channels, and 12-bit ADC deliver the determinism required for lock/unlock, courtesy-light timing, and PWM-driven LED headlamp leveling. AEC-Q100 qualification and the -40C to +85C thermal range meet underhood and cabin-environment derating rules, while the 176-LQFP footprint allows generous trace escape for high-current MOSFET driver outputs alongside CAN transceivers.
推荐
CAN Gateway / Network Hub
The SPC5606SF2CLU6's multiple FlexCAN modules and dedicated message RAM make it an excellent CAN-to-CAN or CAN-to-LIN gateway bridging powertrain, chassis, and body networks. At 64 MHz, it can filter and forward messages at bus speeds up to 1 Mbps with sub-millisecond latency, offloading the central gateway MCU in a zone-oriented E/E architecture. Power-on reset, low-voltage detection, and the integrated voltage regulator simplify the power tree and reduce external components compared with discrete MCU + external CAN bridge ICs.
推荐
HVAC Control Unit with Graphical Display
Climate-control head units with TFT or segment+icon displays run dual-zone logic, blower PWM control, and LIN communication to actuator nodes - all within the SPC5606SF2CLU6's peripheral set. The eQADC digitizes NTC thermistor inputs for cabin and ambient temperature with 12-bit resolution and the eMIOS channels generate the 25 kHz PWM needed for brushless blower drives. Compared with using a small 8-bit MCU plus an external display driver, this single-chip approach cuts board area and reduces integration effort.
推荐
Stepper-Motor Gauge Cluster
Stepper-motor gauges (analog speedometer, tachometer, fuel and temperature pointers) are driven directly by the SPC5606SF2CLU6's eMIOS channels with micro-stepping waveforms, eliminating external stepper drivers and reducing PCB size. The same MCU renders the central TFT display, manages CAN diagnostics, and services OBD-II requests - all inside one device. AEC-Q100 qualification and wide thermal range ensure the electromechanical gauges remain on-spec through a vehicle's lifetime across extreme cabin temperatures.
推荐
Industrial TFT Human-Machine Interface (HMI)
Outside automotive, the SPC5606SF2CLU6 fits rugged industrial HMIs for factory automation and process control where deterministic GPIO, multi-protocol serial, and an integrated TFT controller reduce the bill of materials. The 64 MHz CPU runs embedded GUI libraries such as emWin or Crank Storyboard for HMI panels, while the CAN and SPI peripherals tie the HMI into fieldbus networks. The 176-LQFP package makes the part easy to route on 4-layer industrial PCBs.
推荐
推荐产品汇总
工程参考数据： SPC5606SF2CLU6 ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | SPC5605SF2CLU6 | SPC5607SF2CLU6 | SPC5642AF2MLU1 | SPC5644AF0MLU2 | SPC5746BSK1MKU2 | SPC5602BF2MLL6 |
|---|---|---|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | 176-LQFP (24x24 mm) | 176-LQFP (24x24 mm) | 176-LQFP (24x24 mm) | 176-LQFP (24x24 mm) | 176-LQFP (24x24 mm) | 176-LQFP (24x24 mm) | 176-LQFP (24x24 mm) |
| Core | e200z0h (single core) | e200z0h (single core) | e200z0h (single core) | e200z4 (dual core) | e200z4 (dual core) | e200z4 (lockstep) | e200z0h (single core) |
| Maximum Clock Frequency | 64 MHz | 64 MHz | 64 MHz | 120 MHz | 150 MHz | 180 MHz | 64 MHz |
| Flash Size | 1 MB | 768 KB | 1.5 MB | 2 MB | 3 MB | 4 MB | 768 KB |
| Operating Temperature | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +105C | -40C to +105C | -40C to +125C | -40C to +85C |
| Automotive Qualification | AEC-Q100 | AEC-Q100 | AEC-Q100 | AEC-Q100 | AEC-Q100 | AEC-Q100 | AEC-Q100 |
| Unit Price (qty 1) | $13.81 | $11.50 | $15.20 | $24.50 | $26.30 | $32.40 | $9.80 |
关键差异点
- Purpose-built LCD controller (LCDC) integrated on-chip （对比 STM32H563ZIT6)
- True automotive-grade temperature and qualification （对比 LPC2468FBD208551)
- 1 MB Flash delivers larger application headroom than smaller variants （对比 SPC5602BF2MLL6)
- Single-core design keeps BOM cost low for mid-range clusters （对比 SPC5642AF2MLU1)
设计说明
Decouple each VDD/VSS pair with a 100 nF X7R ceramic in parallel with a 4.7 uF bulk capacitor placed within 5 mm of the package. The SPC5606SF2CLU6 has multiple supply pins (VDD, VDDA, VDDX, VSSS) that must all be tied to low-impedance planes. The internal voltage regulator requires an external ballast transistor and reverse-battery protection - follow the SPC5 hardware design guide reference schematic exactly to avoid POR instability during crank events.
Keep the 40 MHz external crystal traces short, symmetric, and surrounded by a grounded guard ring. Place the crystal within 5 mm of the XTAL pins and avoid routing high-current or TFT data lines across the oscillator area. The 176-LQFP's 0.5 mm pitch pads require 4-layer PCB stack-up; use 1 oz copper and 8 mil-wide escape traces to keep impedance-controlled stubs on the LCD bus within 25 mm.
Do not leave unused FlexCAN pins floating - configure them in software as disabled or tie them to ground through 10 kohm. Watch out for the VDDX voltage tolerance (3.3 V or 5 V variants: verify your board revision). Failing to enable the JTAG security bit before locking production Flash leaves the MCU debuggable - use NXP's HSE secure-boot toolchain to lock the part before volume deployment.
Estimated: with 1.5 W typical power dissipation and a theta_JA of approximately 28 C/W for the LQFP-176 package, the junction-to-ambient rise is roughly 42 C at still air. Derate by 5 C/W for closed plastic enclosures and reserve a copper pour under the exposed die-attach pad as a heat-spreading layer. Automotive clusters at +85 C ambient typically run well inside the 125 C junction limit.
合规信息
AEC-Q100 qualified per NXP product page. RoHS and REACH compliance stated by distributor listings. Halogen-free status not explicitly disclosed in the verified web data - set to unknown.
