STM32L011G3U6 - 32MHz Cortex-M0+ MCU | STMicroelectronics
料号: STM32L011G3U6 ✓ 量产中STM32L011G3U6 概述
A microcontroller is a programmable semiconductor that integrates a processor core, nonvolatile program memory, working memory, peripherals and communication interfaces on one device. The STM32L0 access-line family combines a compact Arm Cortex-M0+ processor with energy-focused design, providing a platform for control, sensing, communication and data acquisition without requiring a separate processor and external memory.
The STM32L011G3U6 includes an Arm Cortex-M0+ RISC core, 8 KB Flash and 32 MHz processing capability. Its 28-UFQFPN 4 x 4 mm package supports compact PCB layouts, while the supported 1.8 V, 2.5 V and 3.3 V operating levels accommodate both low-voltage energy-harvesting systems and conventional 3.3 V electronics. The manufacturer describes the STM32L011x3/x4 family as an ultra-low-power access-line platform.
The device is organized around the Arm Cortex-M0+ architecture, a 32-bit RISC instruction set designed for efficient embedded control. Flash memory retains programmed firmware when power is removed, allowing autonomous operation after reset. The manufacturer product page identifies reset and supply-management functions as part of the family architecture, supporting compact systems that need controlled startup behavior and predictable power management.
Typical uses include battery-powered sensor nodes, compact industrial control modules, low-power IoT endpoints, wearable accessories, metering equipment and embedded instruments. The small package is particularly useful where board area is constrained but a general-purpose 32-bit control platform is required. Designers should select the appropriate external clock, decoupling and programming connections according to the manufacturer's pin and application guidance.
A key design consideration is the balance between processing capability, low-power operation and board density. The 8 KB Flash capacity should be checked against the final firmware image, including bootloader, application code and configuration data. The 32 MHz maximum CPU frequency also requires attention to clock configuration, peripheral timing and power-management settings during firmware development.
This product reference combines the device's principal architecture, memory, package and supply information with practical design guidance, sourcing questions, and a clear comparison against related STMicrocontrollers. It is intended to help engineers evaluate fit, plan firmware and hardware integration, and determine whether the STM32L011G3U6 belongs in an ultra-low-power embedded design.
直接替换替代料: STM32L011G3U6 ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
该产品暂无直接替换替代料。
请求替代料STM32L011G3U6 最大额定值与电气特性
| Product Type | 32-bit ultra-low-power microcontroller |
| Processor Core | Arm Cortex-M0+ |
| Instruction Set | 32-bit RISC |
| Maximum CPU Frequency | 32 MHz |
| Flash Memory | 8 KB |
| Flash Organization | 8K x 8 bits |
| Supported Supply Voltage | 1.8 V, 2.5 V or 3.3 V |
| 封装 | 28-UFQFPN, 4 x 4 mm |
| 引脚数量 | 28 pins |
| 安装类型 | Surface mount |
| Delivery Format | Tray |
| Series | STM32L0 |
| Family | STM32L011x3/x4 access line |
| Core Architecture | Arm Cortex-M0+ RISC |
| Reset and Supply Management | Supported |
STM32L011G3U6 28-ufqfpn, 4 x 4 mm 引脚配置指南
STM32L011G3U6(28-ufqfpn, 4 x 4 mm 封装)的引脚配置。 该数字 IC 包含 GPIO、通信接口(UART、SPI、I2C)和电源引脚。请参阅制造商数据手册以了解复用引脚功能和配置选项。对嵌入式系统设计和 PCB 布局至关重要。
暂无详细引脚数据: STM32L011G3U6.
请参阅 数据手册 以查看完整引脚配置。
典型应用
STM32L011G3U6 适用于 6 应用s: Battery-Powered Sensor Node, Compact Industrial Control Module, Low-Power IoT Endpoint, Portable Metering Instrument, Wearable Accessory Controller, Embedded Test and Measurement Instrument.
Battery-Powered Sensor Node
The STM32L011G3U6 fits a compact sensor node because its Arm Cortex-M0+ core provides 32-bit control at up to 32 MHz while the device belongs to an ultra-low-power STM32L0 access-line family. The 8 KB Flash is suitable for small acquisition, thresholding and communication-control firmware, provided the final image fits with margin. Its 28-UFQFPN 4 x 4 mm package reduces board area, and support for 1.8 V, 2.5 V and 3.3 V supplies permits integration with low-voltage sensors. For battery life, configure the MCU's sleep modes, peripheral clocks and wake sources carefully and measure the complete operating profile rather than relying on CPU frequency alone.
推荐
Compact Industrial Control Module
STM32L011G3U6 is appropriate for compact industrial controls that need deterministic embedded processing without a large processor footprint. Its Cortex-M0+ RISC core operates up to 32 MHz, while the 28-UFQFPN package leaves board perimeter available for connectors and protection components. The device's 1.8 V, 2.5 V and 3.3 V operating choices support multiple industrial interface arrangements. Engineers should verify every required peripheral, I/O count and timing function against the manufacturer pin table. Firmware should include appropriate fault handling and watchdog strategy, while PCB design should isolate switching nodes and provide stable decoupling close to the device.
推荐
Low-Power IoT Endpoint
The STM32L011G3U6 can form the control core of a low-power IoT endpoint when the application fits within 8 KB of Flash and uses a small number of external interfaces. The 32 MHz Cortex-M0+ core can execute protocol framing, sensor management and local state handling, while the 4 x 4 mm 28-pin package supports dense terminal-board layouts. Selection should account for radio-control signals, antenna interfaces and any buffering that cannot be integrated into the MCU. Low-power performance depends on the selected system architecture, including sleep duration, wake-up frequency and radio current, so evaluate the complete product duty cycle with representative peripheral loads.
推荐
Portable Metering Instrument
STM32L011G3U6 suits portable metering equipment where low power, compact packaging and local control are important. The device's 8 KB Flash can hold a focused firmware image for measurement sequencing, calibration handling and data output, while its Cortex-M0+ architecture provides a 32-bit processing platform at up to 32 MHz. Its supply-voltage options allow design flexibility around sensor and display circuitry. For accurate measurement, use the manufacturer guidance for analog-capable pins, reference routing and grounding. Keep sensitive analog paths away from fast digital return currents and verify the selected operating voltage against all peripheral and I/O limits before schematic release.
推荐
Wearable Accessory Controller
The STM32L011G3U6 is a logical controller for a small wearable accessory because its 28-UFQFPN 4 x 4 mm package occupies little board area and its STM32L0 family emphasizes ultra-low-power operation. The 32 MHz Cortex-M0+ core is appropriate for gesture logic, sensor coordination and communication sequencing, provided the application remains within the 8 KB Flash constraint. Low-voltage operation at 1.8 V, 2.5 V or 3.3 V can simplify integration with compact battery and sensor systems. Mechanical and thermal design remain critical: keep the MCU away from heat-generating components, minimize exposed area where needed, and confirm package details against the manufacturer drawing.
推荐
Embedded Test and Measurement Instrument
STM32L011G3U6 can be used in small test and measurement instruments when the required firmware, interface count and memory fit its 8 KB Flash limit. The 32 MHz Cortex-M0+ RISC core supports control sequencing, configuration handling and data formatting, while the compact 28-pin UFQFPN package preserves space for analog, power and connector sections. The device supports 1.8 V, 2.5 V and 3.3 V configurations, enabling tailored rail selection. Use the manufacturer pin descriptions to choose appropriate signal types, and follow the application guidance for decoupling and clock configuration. A higher-memory STM32 family may be preferable if data logging, complex UI control or extensive protocol stacks exceed the available Flash.
推荐
推荐产品汇总
工程参考数据: STM32L011G3U6 ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | STM32G0C1KEU6N | STM32G474CET6 |
|---|---|---|---|
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics |
| Series | STM32L0 | STM32G0 | STM32G4 |
| Pin-to-Pin Compatibility | Reference footprint | Not established as drop-in | Not established as drop-in |
关键差异点
- Compact STM32L0 access-line implementation (对比 STM32G0C1KEU6N)
- Low-voltage supply flexibility (对比 STM32G474CET6)
- Dedicated 32-bit control platform (对比 ATTINY13A-SUR)
设计说明
Choose the supply rail and operating mode from the manufacturer's electrical limits before laying out the power network. The STM32L011G3U6 supports 1.8 V, 2.5 V and 3.3 V configurations, but the selected voltage also constrains I/O behavior, clocking and peripheral use. Place the required bulk and high-frequency decoupling capacitors close to their associated pins, keep the return path short and verify startup behavior for the complete rail arrangement.
Use the manufacturer package drawing and land pattern rather than a generic square-QFN footprint. The 28-UFQFPN is only 4 x 4 mm, so small routing errors can move a trace beneath the exposed thermal area or interfere with adjacent pads. Confirm pin-one orientation, pad dimensions, solder-mask clearance and the exposed-pad connection against the official package drawing before releasing artwork.
The 8 KB Flash limit is the most immediate design constraint. Budget space for startup code, peripheral drivers, communication handlers, calibration data and future fixes rather than sizing the design from application code alone. Also verify the number and electrical type of required I/O pins, since a firmware-compatible MCU in a different package cannot be substituted without a PCB redesign.
Validate battery life using the complete duty cycle, including sensor conversion, communications, processing and sleep periods. A 32 MHz maximum CPU frequency describes performance capability, not continuous power consumption. Use the manufacturer's clock-tree, sleep-mode and peripheral-control guidance to prevent unused blocks from remaining clocked, and measure current at the system level with the intended firmware and external loads.
Assign sensitive analog or communication-adjacent pins early and route them away from switching and high-current paths. Keep oscillator and reset-related connections short, follow the reference-circuit values in the manufacturer application information, and provide clean ground references beneath and around the device. Although the MCU is compact, disciplined return-current planning is important for reliable low-voltage operation and electromagnetic behavior.
合规信息
The available product information confirms the STM32L011G3U6 identity, architecture, memory, voltage configurations, package and delivery format but does not explicitly state the requested compliance declarations. Confirm RoHS, REACH, lead-free, halogen-free, conflict-minerals and automotive qualification status in the current manufacturer documentation before production release.