XC7A100T-L2FGG484E - 101,440-Cell Artix-7 FPGA | AMD
料号: XC7A100T-L2FGG484E ✓ 量产中XC7A100T-L2FGG484E 概述
An FPGA is a semiconductor whose digital functionality is defined after manufacture through a configuration bitstream. Within the product hierarchy, the XC7A100T-L2FGG484E is an Artix-7 FPGA, which belongs to the 7-series FPGA family and the broader category of programmable logic devices. This makes it appropriate when fixed-function logic is insufficient but an ASIC or large processor-based implementation would be unnecessarily complex.
Key resources include 101,440 logic cells, 7,925 configurable logic blocks, 285 I/O, and up to 1,286 MHz operation as identified in the manufacturer-family product listing. The device combines programmable logic with DSP and block-RAM resources, allowing parallel arithmetic, control logic, data acquisition, and communications functions to share one device. Its I/O count supports systems with substantial external data, control, display, memory, and network connectivity requirements.
The 28 nm CMOS implementation supports lower system power than larger 7-series devices while preserving high clock rates and programmable I/O performance. The L2 ordering code identifies the specified Artix-7 configuration, while FGG484 denotes the 484-pin fine-pitch BGA package. The E suffix follows the manufacturer's ordering nomenclature and should not be interpreted independently without the family documentation.
Typical applications include industrial control, camera and image processing, robotics, communications infrastructure, test and measurement, embedded signal processing, and compact edge-computing systems. Parallel programmable logic is particularly effective for sensor aggregation, protocol handling, waveform processing, and real-time control loops.
A new design should confirm the complete power architecture, decoupling strategy, configuration interface, clocking plan, PCB stack-up, and pin assignments against the manufacturer data sheet and package pinout files. The 484-pin FBGA requires careful escape-routing planning, multilayer PCB construction, via-in-pad or via-adjacent fanout, and thermal management appropriate to utilization and ambient temperature.
This page combines verified product identity, package and resource details, practical application guidance, and design-focused comparison information to support faster engineering evaluation and sourcing decisions.
直接替换替代料: XC7A100T-L2FGG484E ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: XC7A100T-L2FGG484E (相同外形与封装尺寸) ——差异在于 Package, Logic Cells, Process Technology, Core Supply Voltage, Device Type.
XC7A100T-3FGG484E
✅ 直接替换联系询价
查看数据手册 →XC7A100T-2FGG484C
✅ 直接替换联系询价
查看数据手册 →XC7A100T-2FGG484I
✅ 直接替换✓ 有现货
$45.9375 / 个
查看数据手册 →XC7A100T-2FGG484C
✅ 直接替换 ⚠️ 规格未核验联系询价
查看数据手册 →XC7A100T-3FGG484E
✅ 直接替换 ⚠️ 规格未核验联系询价
查看数据手册 →XC7A100T-L2FGG484E 最大额定值与电气特性
| Device Type | Artix-7 Field-Programmable Gate Array (FPGA) |
| Logic Cells | 101,440 cells |
| Configurable Logic Blocks | 7,925 CLBs |
| Maximum Operating Frequency | 1,286 MHz |
| Input/Output Count | 285 I/O |
| Process Technology | 28 nm CMOS |
| Core Supply Voltage | 1 V |
| 封装 | 484-pin FBGA |
| Package Designation | FGG484 |
| Device Family | Artix-7 |
| Product Series | XC7A100T |
| Architecture | 7-series FPGA |
| Programming Technology | Configuration memory |
| 安装类型 | Surface mount |
| Packaging Form | Tray |
XC7A100T-L2FGG484E fgg484 引脚配置指南
XC7A100T-L2FGG484E(fgg484 封装)的引脚配置。 该数字 IC 包含 GPIO、通信接口(UART、SPI、I2C)和电源引脚。请参阅制造商数据手册以了解复用引脚功能和配置选项。对嵌入式系统设计和 PCB 布局至关重要。
暂无详细引脚数据: XC7A100T-L2FGG484E.
请参阅 数据手册 以查看完整引脚配置。
典型应用
XC7A100T-L2FGG484E 适用于 6 应用s: Industrial Control and Automation, Camera and Image Processing, Robotics and Motion Control, Communications and Network Interface, Test and Measurement, Embedded Signal Processing.
Industrial Control and Automation
The XC7A100T-L2FGG484E fits machine-control systems requiring deterministic parallel logic, extensive sensor and actuator I/O, and integrated DSP or block RAM. Its 101,440 logic cells and 285 I/O can accommodate multiple control loops, encoder interfaces, interlocks, and communications logic in one programmable device. Parallel hardware execution reduces dependence on a real-time processor for simple sequencing and filtering. The FGG484 package also provides a substantial pin budget for memory, differential interfaces, and expansion connectors, although the exact voltage banks, temperature grade, and industrial qualification must be confirmed against the ordering documentation.
推荐
Camera and Image Processing
The XC7A100T-L2FGG484E is appropriate for camera modules and image-processing pipelines that benefit from parallel pixel handling. Its 101,440 logic cells, DSP resources, and 285 I/O can support parallel pre-processing, color conversion, thresholding, exposure control, and interface adaptation. Dedicated hardware execution provides predictable throughput for each incoming frame. In a practical design, external image-sensor data enters through supported I/O standards, is captured into block RAM or external memory, and is processed through parallel pipelines before being transmitted or compressed. Bank-specific voltage and pin multiplexing must be checked against the official package files.
推荐
Robotics and Motion Control
The XC7A100T-L2FGG484E supports robotic control architectures where low-latency motor command generation, sensor fusion preprocessing, and safety logic must operate concurrently. Its programmable logic can implement encoders, pulse-width modulation, interpolation, and fieldbus framing in parallel, while DSP resources handle filters and transforms. The 285 available I/O provide connections for encoders, resolvers, sensors, actuators, and communications. A dual-processor architecture can place the FPGA in front of a host processor for deterministic timing, though motor-drive isolation, grounding, protection, and fail-safe behavior must remain separate from the digital FPGA subsystem.
推荐
Communications and Network Interface
The XC7A100T-L2FGG484E can implement protocol bridges, packet processors, and hardware-assisted network functions because its programmable resources support parallel data handling. The 101,440 logic cells, block-RAM capability, 285 I/O, and clock-management resources can support transmit and receive datapaths, CRC generation, FIFO management, and stream conversion. Using the FPGA for fixed-rate framing and the host processor for control-plane management can improve throughput and isolate timing-critical operations. External memory interface requirements, transceiver I/O standards, reference-clock topology, and board-level signal integrity must be verified against the device documentation before schematic capture.
推荐
Test and Measurement
The XC7A100T-L2FGG484E fits automated test equipment requiring parallel stimulus generation, response capture, timing checks, and protocol analysis. Its 285 I/O can connect instruments, fixtures, and digital interfaces, while the large logic-cell and DSP resources allow several test channels to share a common control architecture. Block RAM can buffer acquired samples, and programmable logic can implement real-time pattern generation or error detection. High-speed analog front ends still require separate amplifiers, converters, protection, and controlled-impedance routing. Exact acquisition timing, I/O voltage, and clock-jitter performance should be established through device-level simulation.
推荐
Embedded Signal Processing
The XC7A100T-L2FGG484E is well suited to embedded DSP front ends that must filter, transform, and classify sensor data in real time. Its DSP blocks and programmable logic can execute parallel FIR filters, correlation, FFT-related pipelines, and thresholding more predictably than a general-purpose software processor. The 1 V core supply is supported by multiple I/O and auxiliary supply domains, allowing integration with external memory and mixed-signal interfaces when voltage-bank rules are respected. Designers should budget DSP, block RAM, routing, and clock resources in the implementation tools because advertised logic-cell counts do not directly predict attainable clock frequency.
推荐
推荐产品汇总
工程参考数据: XC7A100T-L2FGG484E ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | XC7A100T-3FGG484E | XC7A100T-2FGG484C | XC7A100T-2FGG484I | XC7A100T-2FGG484C | XC7A100T-3FGG484E |
|---|---|---|---|---|---|---|
| Brand | AMD | AMD | AMD | AMD | AMD | AMD |
| Package | 484-pin FBGA (FGG484) | 484-pin FBGA (FGG484) | 484-pin FBGA (FGG484) | 484-pin FBGA (FGG484) | 484-pin FBGA (FGG484) | 484-pin FBGA (FGG484) |
| FPGA Family | Artix-7 | Artix-7 | Artix-7 | Artix-7 | Artix-7 | Artix-7 |
| Logic Cells | 101,440 cells | 101,440 cells | 101,440 cells | 101,440 cells | 101,440 cells | 101,440 cells |
| Configurable Logic Blocks | 7,925 CLBs | 7,925 CLBs | 7,925 CLBs | 7,925 CLBs | 7,925 CLBs | 7,925 CLBs |
| Input/Output Count | 285 I/O | 285 I/O | 285 I/O | 285 I/O | 285 I/O | 285 I/O |
| Process Technology | 28 nm CMOS | 28 nm CMOS | 28 nm CMOS | 28 nm CMOS | 28 nm CMOS | 28 nm CMOS |
| Core Supply Voltage | 1 V | 1 V | 1 V | 1 V | 1 V | 1 V |
| Speed Ordering | -2 ordering with L2E suffix | -3 ordering | -2 ordering | -2 ordering | -2 ordering | -3 ordering |
关键差异点
- Matches the exact target ordering code (对比 XC7A100T-2FGG484C)
- Higher listed operating frequency than the conventional -2 family variants (对比 XC7A100T-2FGG484I)
- Large logic and I/O capacity in a compact BGA (对比 XC7A100T-3FGG484E)
- Same-package consolidation across speed and suffix options (对比 XC7A100T-2FGG484C)
设计说明
Plan the FGG484 power tree around the device's 1 V core supply and all required I/O and auxiliary rails. Follow the manufacturer decoupling recommendations, place the smallest effective bypass capacitors directly at the relevant supply pins, and provide additional bulk energy near the regulator outputs. Separate sensitive analog or clock-supply paths from switching-converter stages where practical. Use the AMD power-estimation tools with actual toggle rates and utilization; do not size the supply from the 1,286 MHz family figure because actual power depends on clocking, logic activity, I/O standards, and configuration state.
Use AMD's Artix-7 package pinout files as the controlling source for all 484 package positions. Match bank assignments, VCCO requirements, differential-pair rules, configuration pins, and dedicated pins to the selected design before PCB routing. The 285 I/O figure does not imply that every listed position can be used as a general-purpose user I/O. Define a multilayer stack-up with continuous power and ground planes, controlled-impedance routing, and a BGA escape strategy that matches the fabricator's via and pad rules. Keep high-speed memory and configuration traces short and away from switching nodes.
Thermal performance must be evaluated at the expected switching activity and ambient temperature, not from logic-cell utilization alone. Provide copper planes beneath the BGA and sufficient top-side copper or heat-spreader area where the mechanical design permits. Use the manufacturer's power estimate to calculate junction temperature with the actual board thermal model. Keep high-current I/O and external-memory routing distributed where practical to avoid local hot spots. Validate the assembly through power cycling and temperature measurement, since configuration, I/O activity, and adjacent components can materially change the thermal result.
Do not treat sharing the FGG484 footprint as proof that every XC7A100T suffix is an unrestricted substitute. Confirm speed ordering, temperature grade, power limits, configuration features, and lifecycle intent in the AMD ordering table for the exact part number. When changing suffixes, regenerate constraints, verify the pin report, run timing analysis, and perform configuration testing. Also confirm whether legacy configuration data is reusable; a footprint-compatible device can still differ in configuration-security or operating-order characteristics that affect production deployment.
合规信息
The verified product listings identify RoHS-related category information but do not provide an explicit compliance declaration for this exact MPN. Automotive qualification is not applicable to the listed industrial FPGA ordering family unless the manufacturer documents a separate qualified grade.